Advertisement
Table of Contents
- 1 Table of Contents
- 2 Preparing the Fan Site
- 3 Getting Ready
- 4 Installing the Hanger Bracket
- 5 Assembling and Hanging the Fan
- 6 Wiring the Fan
- 7 Installing the Canopy and Canopy
- 8 Assembling the Blades
- 9 Completing Your Installation with or Without a Bowl Light Fixture
- 10 Operating and Cleaning Your
- 11 Troubleshooting
- Download this manual
For Your Records and
Warranty Assistance
For reference, also attach your receipt or a copy
of your receipt to the manual.
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
Form# 45065-01
200
©2009 Hunter Fan Co.
Type 2 Models
Type 2 Models
Type 2 Models
Owner's Guide and Installation Manual
Advertisement
Table of Contents
Related Manuals for Hunter 45065-01
Summary of Contents for Hunter 45065-01
- Page 1 For reference, also attach your receipt or a copy of your receipt to the manual. __________________________________________ Model Name __________________________________________ Model No. __________________________________________ Date Purchased __________________________________________ Where Purchased Form# 45065-01 ©2009 Hunter Fan Co. Type 2 Models Type 2 Models Type 2 Models Owner’s Guide and Installation Manual...
-
Page 2: Table Of Contents
Table Of Contents Preparing the Fan Site . . . . . . . . . . . . . . . . . 3 1 •... -
Page 3: Preparing The Fan Site
If you want to use an existing fan site, complete the following checklist to determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page. - Page 4 3-1. Attach a 2” x 4” support brace between two joists. Position it to allow you to recess the bottom of the outlet box a minimum of 1/16” into the ceiling. 3-2. Check the support brace to ensure it will support the full weight of the fan and light kit.
- Page 5 Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include instructions for all three Installer’s Choice mounting methods.
-
Page 6: Getting Ready
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •... -
Page 7: Installing The Hanger Bracket
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer 3” Screw 45065-01 • 11/05/09 • Hunter Fan Company Isolator Hanger Bracket Ceiling Peak Ceiling Peak... -
Page 8: Assembling And Hanging The Fan
3-1 – 3-3. For low profile mounting (ceilings less than 8 feet high), go to steps 3-6 – 3-9 on the next page. 3-1. To assemble fan to hang down from a flat or angled ceiling, place the canopy and canopy trim ring around the adapter so that they rest on the fan assembly. - Page 9 3-9. Align the screw holes in the washer with the holes in the adapter. Assemble securely with three #8-32 x 3/4” screws. 3-10. Raise the fan and place the hook on the hanger bracket through the round hole in the rim of the canopy.
-
Page 10: Wiring The Fan
4-3. Connect the bare or green ground wire (grounding) from the ceiling to the green ground wire (grounding) from the ceiling plate and the green ground wire from the fan or the green ground wire present on the low profile washer. -
Page 11: Installing The Canopy And Canopy
Should you need to remove the canopy trim ring, follow these steps: 1. Twist canopy trim ring counter clockwise until it releases from canopy. Step 5-5 45065-01 • 11/05/09 • Hunter Fan Company Steps 5-1 – 5-2 Canopy Step 5-4 Canopy Screw... -
Page 12: Assembling The Blades
Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. 6-2. Attach each blade to a blade iron using three blade assembly screws. -
Page 13: Completing Your Installation With Or Without A Bowl Light Fixture
7 • Completing Your Installation With or Without a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button. This feature gives you the option of installing the fan with OR without the included light fixture. - Page 14 Align the side screw holes in the upper and lower switch housings. Attach the lower switch housing to the upper switch housing with three housing assembly screws. 45065-01 • 11/05/09 • Hunter Fan Company Steps 7-6 – 7-7 Lower Switch...
- Page 15 7-8. First install B10 candelabra bulbs (60 Watt Maximum) into the sockets. 7-9. Thread the light and fan pull chains through the hole in the center of the glass bowl. Then, thread the light pull chain through the hole in the center of the cover plate.
- Page 16 7-19. Install the switch housing cap and plug button to the lower switch housing. 7-20. Once you have uninstalled the light fixture, continue with step 7-6. Male Dummy Terminal Female Dummy Terminal 45065-01 • 11/05/09 • Hunter Fan Company Lower Switch Step 7-14 Plug Button Housing Screw Step 7-19...
-
Page 17: Operating And Cleaning Your
8 • Operating and Cleaning Your Ceiling Fan 8-1. Turn on electrical power to the fan. 8-2. The fan pull chain controls power to the fan. The pull chain has five settings in sequence: High, Medium, Low, Serenity Speed, and Off. -
Page 18: Troubleshooting
2. Check to see if the blade is cracked. If so, replace all the blades. Problem: Excessive wobbling. 1. If your fan wobbles when operating, use the enclosed balancing kit and instructions to balance the fan. 2. Tighten all blade iron screws.