Table of Contents
Advertisement
For Your Records and
Warranty Assistance
For reference, also attach your receipt or a copy
of your receipt to the manual.
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
Form# 45062-01
20090701
©2009 Hunter Fan Co.
Type 3 Models
Type 3 Models
Type 3 Models
Owner's Guide and Installation Manual
Advertisement
Table of Contents
Related Manuals for Hunter 45062-01
Summary of Contents for Hunter 45062-01
- Page 1 For reference, also attach your receipt or a copy of your receipt to the manual. __________________________________________ Model Name __________________________________________ Model No. __________________________________________ Date Purchased __________________________________________ Where Purchased Form# 45062-01 20090701 ©2009 Hunter Fan Co. Type 3 Models Type 3 Models Type 3 Models Owner’s Guide and Installation Manual...
-
Page 2: Table Of Contents
5 • Wiring the Fan . . . . . . . . . . . . . . . . . . - Page 3 Understanding Mounting and Installer’ s Choice® Hunter’s patented 2-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of two ways, depending on ceiling height and your preference: Standard or Angled mounting. The steps in this manual include instructions for both Installer’s Choice mounting methods.
-
Page 4: Getting Ready
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •... -
Page 5: Installing The Hanger Bracket
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer 3” Screw 45062-01 • 07/01/09 • Hunter Fan Company Isolator Hanger Bracket Ceiling Peak Ceiling Peak... -
Page 6: Assembling And Hanging The Fan
You can assemble your fan for standard or angled mounting as shown in steps 3-1 – 3-3. 3-1. To assemble fan to hang down from a flat or angled ceiling, insert the downrod through the canopy, adapter cover grommet, adapter cover, and canopy trim ring. (The adapter cover and adapter cover grommet may already be attached to make one piece.) -
Page 7: Setting The Remote Transmitter And Receiver
4-3. Install the included 9-volt battery into the transmitter. CAUTION: The remote control device complies with part 15 of the FCC rules. Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment. -
Page 8: Wiring The Fan
Small Wire Connector 45062-01 • 07/01/09 • Hunter Fan Company 5 • Wiring the Fan 5-1. Before attempting installation, make sure the power is still off. 5-2. To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. -
Page 9: Installing The Canopy And Canopy
Should you need to remove the canopy trim ring, follow these steps: 1. Twist canopy trim ring counter clockwise until it releases from canopy. Step 6-5 45062-01 • 07/01/09 • Hunter Fan Company Steps 6-1 – 6-2 Canopy Step 6-4 Canopy Screw... -
Page 10: Light Fixture
7 • Completing Your Installation With a Light Fixture Your Hunter fan comes with an integrated light fixture assembly. WARNING: Use only the light fixture supplied with this fan model. 7-1. To attach the light kit top housing, partially install two housing assembly screws into the light kit mounting plate. - Page 11 7-7. Lift the globe up to the light kit top housing. Align the three bolts on the globe with the three slots in the light kit top housing. 7-8. Rotate the globe clockwise until tight. 45062-01 • 07/01/09 • Hunter Fan Company Spring Clamp Steps 7-5 – 7-6 Slot...
-
Page 12: Mounting The Holder
8-4. You can mount the remote holder to any toggle switch plate with the screws already in the switch plate. Or, you can simply mount the remote holder on the wall. 45062-01 • 07/01/09 • Hunter Fan Company Fan Speed High Fan Speed Steps 8-1 –... -
Page 13: Ceiling Fan
Clean wood finish blades with a furniture polishing cloth. Occasionally, apply a light coat of furniture polish for added protection and beauty. Clean painted and high-gloss blades in the same manner as the fan finish. 45062-01 • 07/01/09 • Hunter Fan Company... -
Page 14: Troubleshooting
Problem: Lights dim when turned on or do not turn on 1. Check to make sure the wattage and type of light bulbs installed match the specifications on the light socket. 45062-01 • 07/01/09 • Hunter Fan Company 10 • Troubleshooting If you need parts or service assistance, please call...