Page 3
Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include instructions for all three Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer 3” Screw 45032-01 • 11/05/08 • Hunter Fan Company Isolator Hanger Bracket Ceiling Peak Ceiling Peak...
3-1 – 3-3. For low profile mounting (ceilings less than 8 feet high), go to steps 3-6 – 3-9 on the next page. 3-1. To assemble fan to hang down from a flat or angled ceiling, place the canopy and canopy trim ring around the adapter so that they rest on the fan assembly.
Page 7
3-9. Align the screw holes in the washer with the holes in the adapter. Assemble securely with three #8-32 x 3/4” screws. 3-10. Raise the fan and place the hook on the hanger bracket through the round hole in the rim of the canopy.
4-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 45032-01 • 11/05/08 • Hunter Fan Company 4 •Wiring the Fan Wire...
Should you need to remove the canopy trim ring, follow these steps: 1. Twist canopy trim ring counter clockwise until it releases from canopy. Step 5-5 45032-01 • 11/05/08 • Hunter Fan Company Steps 5-1 – 5-2 Canopy Step 5-4 Canopy Screw...
Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. 6-2. Attach each blade to a blade iron using three blade assembly screws.
7 • Completing Your Installation With or Without a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button. This feature gives you the option of installing the fan with OR without the included light fixture.
Page 12
190 Watts. Exceeding that limit or the marked limit on this product may result in fire hazard or improper operation. 45032-01 • 11/05/08 • Hunter Fan Company Steps 7-6 – 7-7 Lower Switch Housing...
Page 13
7-9. If the fandangle is attached to the extra pull chain, remove it now. 7-10. Thread the fan pull chain through the hole in the metal disc. Then, thread the fan pull chain through the hole in the center of the glass bowl.
Page 14
7-21. Install the switch housing cap and plug button to the lower switch housing. 7-22. Once you have uninstalled the light fixture, continue with step 7-6. Male Dummy Terminal Female Dummy Terminal 45032-01 • 11/05/08 • Hunter Fan Company Lower Switch Step 7-18 Plug Button Housing Step 7-21...
8 • Operating and Cleaning Your Ceiling Fan 8-1. Turn on electrical power to the fan. 8-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low and Off. • Pull the chain slowly to change settings.
Problem: Lights dim when turned on or do not turn on 1. Check to make sure the wattage and type of light bulbs installed match the specifications on the light socket. 45032-01 • 11/05/08 • Hunter Fan Company 9 • Troubleshooting If you need parts or service assistance, please call 888-830-1326 or visit us at our Web site at http://www.hunterfan.com.