Advertisement

AR4xS-MF
AR1xS-MF
AR10S-MF AR11S-MF AR40S-
MF AR41S-MF
Installation and Mounting
Version 6.0
Siemens AB
Security Products

Advertisement

Table of Contents
loading

Summary of Contents for Siemens AR4 S-MF Series

  • Page 1 AR4xS-MF AR1xS-MF AR10S-MF AR11S-MF AR40S- MF AR41S-MF Installation and Mounting Version 6.0 Siemens AB Security Products...
  • Page 2 Data and design subject to change without notice. / Supply subject to availability. © 2013 Copyright by Siemens AB We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.
  • Page 3: Table Of Contents

    Content 1 Introduction 2 Technical data 3 Safety regulations 3.1 Standards and guidelines 4 Reader components 5 Mounting and connecting 5.1 Surface mounted reader 5.2 Surface mounted reader with cables fed from outside 5.3 Back box mounted reader 5.4 Back box mounted reader with adapter plate 5.5 Connecting the cables 5.6 Disassembling the reader 6 Default settings...
  • Page 4: Introduction

    They can be cleaned with most kind of domestic detergents. All readers have a multicolour light frame. The AR40S-MF and AR41S-MF also have a keypad and a high contrast display. *) Only valid for SiPass integrated MP2.65 – or later Siemens AB 2013-09-30 Security Products...
  • Page 5: Technical Data

    CE according to R&TT and EMC Directives Directives * Only applicable for surface mounted readers. Back box mounted readers are specified from -10°C to +55°C. ** Only applicable for surface mounted readers. Back box mounted readers are specified to IP3X. Siemens AB 2013-09-30 Security Products...
  • Page 6: Safety Regulations

    3.1 Standards and guidelines European directives Siemens Security Products hereby declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC on Electromagnetic Compatibility (EMC). The EC Declaration of Conformity is available from your Siemens sales office or: Siemens AB Englundavägen 7...
  • Page 7: Reader Components

    4 Reader components 1. Hinge 6. Screw for removal from wall tamper protection 2. Base 7 Front 3. Cord gasket 8. Back box plate 4. Knock outs x 4 9. Adapter plate (AR11S-MF, AR41S-MF) Tamper base Siemens AB 2013-09-30 Security Products...
  • Page 8 4   Reader components 1. Screws for back box plate 2. Connector 3. Opening tool – please note that this is a symbolic depiction of the opening tool 4. Extension cable (AR11S-MF, AR41S-MF) Siemens AB 2013-09-30 Security Products...
  • Page 9: Mounting And Connecting

    For connecting the cables to the reader, please refer to: Connecting the cables [ > 15]. Siemens AB 2013-09-30 Security Products...
  • Page 10: Surface Mounted Reader

    3. In case that the removal from wall tamper protection is required, fix the screw into the hole under the tamper base. Ensure to not use excessive force since this can damage the tamper base. 4. Continue to follow the instructionsConnecting the cables [ > 15]. Siemens AB 2013-09-30 Security Products...
  • Page 11: Surface Mounted Reader With Cables Fed From Outside

    4. Hammer the screw driver handle. This will create enough pressure to crack the exact area of the base which will release the knock out. 5. Tilt the knock out with the screwdriver. 6. Pull the knock out away from the base. Siemens AB 2013-09-30 Security Products...
  • Page 12 9. Feed the cables through the opening and reinsert the cord gasket. Proceed to the instructions for Connecting the cables [ > 15]. It is recommended to seal the gap which the knock out creates. Please note that a reader with a removed knock out is not IP 55. Siemens AB 2013-09-30 Security Products...
  • Page 13: Back Box Mounted Reader

    Use only the screws included in the packet for the lower part of the base since those ensure that the reader front will fit perfectly to be securely fitted over the back box. 3. Continue to follow the instructions for Connecting the cables [ > 15] Siemens AB 2013-09-30 Security Products...
  • Page 14: Back Box Mounted Reader With Adapter Plate

    3. Continue to follow the instructions for Connecting the cables [ > 15] The adapter plate is to be used for square back boxes which measure 70 mm x 70 mm. The adapter plate is used for common UK square boxes. Siemens AB 2013-09-30 Security Products...
  • Page 15: Connecting The Cables

    But if it is an intermediate reader on the bus, the jumper must be removed (or placed in OFF position). 5. Place the front of the reader with an angle to the hinges at the top of the base. Siemens AB 2013-09-30 Security Products...
  • Page 16 5   Mounting and connecting 6. Fold the front down until the snap lock confirms a secure attachment. Siemens AB 2013-09-30 Security Products...
  • Page 17: Disassembling The Reader

    2. Push gently and lift the front of the base. To remove the connector: 1. Insert the opening tool as indicated on the picture. 2. Push down gently and tilt the connector away from the base. Siemens AB 2013-09-30 Security Products...
  • Page 18: Default Settings

    Configuration Card Creation Tool (3CT), which enables for required settings to be used for the card readers. For further information, please contact the supplier of this reader. The readers use FreeRTOS. For further information, please visit www.freertos.org. Siemens AB 2013-09-30 Security Products...
  • Page 19: Connecting Card Reader To Sipass Integrated

    Please note that a new card reader will always get the next free bus address. Should a card reader with bus address 5 be removed and a new card reader be installed, the new card reader will get address 5. Siemens AB 2013-09-30 Security Products...
  • Page 20: Disposal

    It is a precondition for reuse and recycling of used electrical and electronic equipment. For more detailed information about dis- posal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. Siemens AB 2013-09-30 Security Products...
  • Page 21 Scale 1:1 Units: mm 12.5 42.5...
  • Page 22 Issued by Siemens AB Industry Sector Security Products International Headquarter © 2013 Copyright by Siemens AB Englundavägen 7 Data and design subject to change without notice. SE-171 24 Solna Supply subject to availability. Tel. +46 8 629 0300 www.siemens.com/securityproducts Document Nr...

This manual is also suitable for:

Ar1 s-mf seriesAr10s-mfAr11s-mfAr40smfAr41s-mf

Table of Contents