Leica ComGate10 User Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Leica ComGate10

User Manual

Monitoring

Solutions

Version 3.0

English

Table of Contents

Summary of Contents for Leica ComGate10

Page 1 Leica ComGate10 User Manual Monitoring Solutions Version 3.0 English...
Page 2 Please contact your local Leica Geosystems representative to transfer your sugges- tions. Leica Geosystems On the last page of this manual, you can find the address of Leica Geosystems head- Address Book quarters. For a list of regional contacts, please visit http://leica-geosystems.com/contact-us/sales_support.
Page 3 Add all products that you and your company own and explore your world of Leica Geosystems: View detailed information on your prod- ucts and update your products with the latest software and keep up- to-date with the latest documentation.
Page 4: Table Of Contents
Care and Transport Transport Storage Cleaning and Drying Technical Data General Technical Data Interfaces Cables to Connect Leica Sensors and External Devices to the ComGate10 Short Message Service (SMS) Conformity to National Regulations Software Licence Agreement Leica ComGate10, Table of Contents...
Page 5: Safety Directions
 Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner. Leica ComGate10, Safety Directions...
Page 6: Definition Of Use
• To ensure that it is used in accordance with the instructions. • To be familiar with local regulations relating to safety and accident prevention. • To inform Leica Geosystems immediately if the product and the application becomes unsafe. • To ensure that the national laws, regulations and conditions for the operation of the product are respected.
Page 7: Hazards Of Use
GNSS signal shading. 2) On metallic structures Protection is as described for non-metallic structures, but the air terminals can be connected directly to the conducting structure without the need for down conduc- tors. Leica ComGate10, Safety Directions...
Page 8 Dispose of the product appropriately in accordance with the national regulations in force in your country. Always prevent access to the product by unauthorised personnel. Product-specific treatment and waste management information can be received from your Leica Geosystems distributor. Leica ComGate10, Safety Directions...
Page 9: For The Ac Power Supply
Precautions: Handle power plug and cord with care. 1.5.3 Repairing of Products Only Leica Geosystems authorised service centres are entitled to repair these prod- WARNING ucts. Electromagnetic Compatibility EMC Description...
Page 10 Precautions: Use only the equipment and accessories recommended by Leica Geosystems. When combined with the product, they meet the strict requirements stipulated by the guide- lines and standards. When using computers or other electronic equipment, pay atten- tion to the information about electromagnetic compatibility provided by the manufac- turer.
Page 11: Fcc Statement, Applicable In U
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by Leica Geosystems for compliance WARNING could void the user's authority to operate the equipment.
Page 12: Description Of The System
Description of the System General Leica M-Com series • The ComGate10 provides the communication from the sensors in the field to the Internet by a mobile communication provider (GSM/UMTS/HSDPA/HSUPA/LTE and/or WLAN). • This product portfolio offers easy installation, reliable communication, connection of multiple sensors and external devices and increased mobility for periodic or short term monitoring systems.
Page 13: Software Concept
– for the connection to the Internet by Ethernet cable – for the connection of any other communication module The Leica ComGate10 contains two coupling relays which can be switched digitally, for example to connect warning devices like signal lamps or sirens. One of them can be used to switch the instrument off and on automatically.
Page 14: Power Concept
2.2.3 Power Concept Description The Leica ComGate10 works in the low voltage range 12–48 V DC.  • In order to prevent hazards to an operator or other persons and damage to prop- erty, follow the instructions in chapter "3 Operation" and be sure to observe the precautions in chapter "1 Safety Directions".
Page 15: System Components
USB-serial converter (RS232) d) Ethernet switch for local network e) Ethernet connector for connecting to the Internet f) Mini button to reset the ComGate10 g) Status LEDs h) Connector for first UMTS/LTE antenna i) Connector for second UMTS/LTE antenna (MIMO mode)
Page 16: Cables
USB LED 006179_001 2.4.2 Cables Description This chapter describes cables to connect Leica instruments and external devices to the ComGate10.  All cables listed in this chapter are optional accessories.  All cables with a GEV-description can be ordered from Leica Geosystems.
Page 17 UC-232A adapter. Leica Nivel210 cable Interface cable GEV207 Cable features: • Interface: ComGate10 - Nivel210 • Transmission: Data and power • Type: Shielded • Length: 1.8 m • Wires: • Lemo pins: • Unterminated Leica ComGate10, Description of the System...
Page 18 • Transmission: Data • DB9 male to DB9 female. • Connect this data cable directly to a serial port of the ComGate10 using USB-to- serial converter (ATEN UC-232A). • Leica Geosystems delivers no RS232 cable. • Leica Geosystems delivers no RS232/485 converter. It is a product of ICP DAS Co.
Page 19 • Interface: ComGate10 - warning device • Connect the optional warning devices directly by standard cables to the ComGate10. The cables must be organised locally. • Only an appropriately trained and qualified specialist may install warning devices with a ComGate10.
Page 20: Operation
Refer to section "2.3 ComGate10 and available accessories" for more information. Unpack the ComGate10. Set up DynDNS To operate a ComGate10 over the Internet, a DynDNS account has to be available. account Refer to www.dyndns.com how to create an account. The following information must be available: •...
Page 21 Remove the cover of the SIM card slot.  The small screw of the SIM card slot must not fall into the ComGate10. In order to protect the ComGate10 from damage, the screw must be removed from the internal of the ComGate10 and the ComGate10 must be opened.
Page 22: Power Supply
During the procedure the power supply should not be connected to the main supply.  Connect the power supply to the power input of the ComGate10 by using the terminal block. Connect the black wire of the power supply to the first connector (VGND) of the terminal block.
Page 23 Configuration with Step Description the stand-alone Connect the LAN at the ComGate10 with a Ethernet cable to the PC/laptop. version of the Leica ComBox Manager Install the stand-alone version of the Leica ComBox Manager on the computer: Insert the Leica M-Com ComBox USB card into the notebook or desktop PC download the Leica ComBox Manager from myWorld.
Page 24 Configuration with Step Description the Leica GeoMoS Connect the LAN at the ComGate10 with a Ethernet cable to the PC/laptop. Monitor software Check if the PC/laptop can obtain an IP address automatically: Click Windows -> Start/Run. Type in ncpa.cpl and press Enter.
Page 25: Connections
The number of attached antennas can be configured over the web interface of the ComGate10. If only one antenna is used, it must be attached to WLAN1. However, for better diversity and thus better throughput and coverage, it is highly recommend using two antennas.
Page 26: Mounting
This product must be installed only by an appropriately trained and qualified specialist. WARNING  If the sensor and the ComGate10 are connected to the same power supply, then the voltage used to power the ComGate10 must fulfil the sensor specification. Do not connect higher voltage to the sensor than specified!
Page 27 Bared range of the sensor cable e) Terminal block f) Isolated screwdriver Refer to section "5.3 Cables to Connect Leica Sensors and External Devices to the ComGate10" for detailed information about how to connect each sensor cable with the terminal block (terminal block clamp assignment).
Page 28 853 396 14123_002 Setup with GMX910 GEV270 807 696 GMX910 842 779 722 411 GEV212 750 073 GMX910 842 779 GEV71 439 038 CT-AT467 853 397 GEV97 560 130 ATEN UC-232A GEV197 COMGT10LWEU 743 389 853 396 006187_002 Leica ComGate10, Operation...
Page 29 Setup with Nivel210 GEV270 (RS232) 807 696 NIVEL210 576 198 722 411 GEV207 748 489 NIVEL210 576 198 802 902 CT-AT467 853 397 GEV97 ATEN UC-232A 560 130 GEV204 COMGT10LWEU 748 335 853 396 GEV270 807 696 14126_002 Leica ComGate10, Operation...
Page 30 Power cable strip Terminal Terminal strip strip CAT6 cable CAT6 cable 14127_002 Setup with DTM STS GEV270 RS232 meteo 807 696 sensor 722 411 DTM STS RS232 GEV241 772 184 CT-AT467 853 397 GEV222 COMGT10LWEU 853 396 14129_002 Leica ComGate10, Operation...
Page 31 Converter Power cable TP meteo sensor RS485 837 816 14130_002 Setup with warning devices a) ComGate10 b) Cable c) Warning device 006192_002  Only an appropriately trained and qualified specialist may install warning devices with a ComGate10. Leica ComGate10, Operation...
Page 32 Power supply for instrument  • Instrument can be switched off/on automatically. • Bridge to DO2 has to be set up. • Use GeoMoS, Leica ComBox Manager or SMS for switching the instru- ment. • Switch box will be obsolete. Leica ComGate10, Operation...
Page 33: Led Indicators On Comgate10
LED Indicators on ComGate10 Description of the The ComGate10 has Light Emitting Diode indicators. They indicate the basic instru- LEDs ment status. LED Status Status of the instrument Status LED The ComGate10 is busy due to startup, software or configuration update.
Page 34: Care And Transport
Cleaning and Drying General In general ensure that no dirt (dust, mud, water, and so on) gets into the ComGate10. Product and acces- • Use only a clean, soft, lint-free cloth for cleaning. If necessary, moisten the cloth sories with water or pure alcohol.
Page 35: Technical Data
• DTM STS RS232 meteo sensors • TP meteo sensor RS485 • Geotechnical Sensors in combination with Campbell Dataloggers. • Warning devices, for example signal lamps or sirens. The ComGate10 contains two coupling relays. Both coupling relays can be switched digitally to connect warning devices.
Page 36: Interfaces
USB 2.0 host port. Can be used as USB device server or for software/ configuration updates. Front Ethernet port. To connect the ComGate10 to another device, for example WebCam or PC. Can be used as LAN or WAN interface. Front Ethernet port.
Page 37 3-wire RS-232 (TXD, RXD, GND) Baud rate 300, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 Data bits 7 bit, 8 bit Parity none, odd, even Stop bits 1, 2 Software flow control None, XON/XOFF Hardware flow control None Leica ComGate10, Technical Data...
Page 38 12–48 V DC V GND Power Ground 12–48 V DC RS232, non-isolated RS232, non-isolated RS232, non-isolated Dry contact relay normally open Dry contact relay normally open Dry contact relay normally closed Dry contact relay normally closed Leica ComGate10, Technical Data...
Page 39: Cables To Connect Leica Sensors And External Devices To The Comgate10
Name Description DI1− DI1+ DI2− DI2+ Cables to Connect Leica Sensors and External Devices to the ComGate10 Leica TPS1000/ Interface cable Connector pin Wire colour Sensor signal Terminal block TPS1100/ TPS1200 GEV241 assignment clamp assign- sensor cable ment Power in...
Page 40 006220_001 Interface cable 006221_001 Leica Nivel210 Interface cable Connector pin Wire colour Sensor signal Terminal block sensor cable GEV207 assignment clamp assign- ment Green Data in Blue Data out Power in Black Ground V GND 006216_001 Leica ComGate10, Technical Data...
Page 41 RS485 assignment on RS232/485 converter White Ground (GND) (B) GND Black Power in (+Vcc) (R) +Vs Blue RS485A Data+ TP-MeteoSeonsor-RS485 Yellow RS485B Data− Internet network RJ45 cable connection cable 006227_001 USB-to-serial (ATEN USB-to-serial converter UC-232A) 006228_001 Leica ComGate10, Technical Data...
Page 42: Short Message Service (Sms)
Short Message Service (SMS) Description Use SMS to control the wireless router of the ComGate10. Send an SMS to the phone number of the SIM card in the ComGate10. Valid commands Command Description status An SMS with the following information is returned: •...
Page 43: Conformity To National Regulations
• FCC Part 15, 22 and 24 (applicable in US) national regulations • Hereby, Leica Geosystems AG, declares that the product Leica ComGate10 is in compliance with the essential requirements and other relevant provisions of Direc- tive 1999/5/EC. The declaration of conformity can be consulted at http://www.leica-geosystems.com/ce.
Page 44: Software Licence Agreement
Leica Geosystems. Such software is protected by copyright and other laws and its use is defined and regulated by the Leica Geosystems Software Licence Agreement, which covers aspects such as, but not limited to, Scope of the Licence, Warranty, Intellectual Property Rights, Limitation of Liability, Exclusion of other Assurances, Governing Law and Place of Jurisdiction.
Page 46 816902-3.0.0en Original text Published in Switzerland © 2017 Leica Geosystems AG, Heerbrugg, Switzerland Leica Geosystems AG Heinrich-Wild-Strasse CH-9435 Heerbrugg Switzerland Phone +41 71 727 31 31 www.leica-geosystems.com...

This manual is also suitable for:

Comgt10lweu