Hitachi L300P Series Service Manual page 10

Function mode
Code Function name
b034 RUN time/Power ON time level
b035 Operation direction restrict
b036 Start reduced voltage
b037 Display selection
b040 Torque limit mode selection
Torque limit level 1 setting
b041
(Forward-driving at
4 quadrant mode)
Torque limit level 2 setting
b042 (Reverse-regenerating at
4 quadrant mode)
Torque limit level 3 setting
b043 (Reverse-driving at
4 quadrant mode)
Torque limit level 4 setting
b044 (Forward-regenerating at
4 quadrant mode)
b045 Torque LAD-STOP selection
Reverse run prevention
b046
selection
Selection of non-stop
b050
function at instantaneous
power failure
Start voltage of non-stop
b051
function setting
OV LAD-STOP level of non-
b052
stop function setting
Deceleration time of non-
b053
stop function setting
Deceleration frequency widt h
b054
of non-stop function setting
b080 AM adjustment
b081 FM adjustment
b082 Start frequency adjustment
b083 Carrier frequency setting
b084 Initialize mode
b085 Country code for initialization
Frequency scalar conversion
b086
factor
b087 STOP key enable
Resume on FRS cancellation
b088
mode
b090 BRD usage ratio
b091 Stop mode selection
b092 Cooling fan control
b095 BRD selection
b096 BRD ON level
b098 Thermistor selection
b099 Thermistor error level
b120 Braking control selection
Waiting time for releasing
b121
braking conformation
b122 Waiting time for acceleration
b123 Waiting time for stop
Waiting time for
b124
conformation
b125 Releasing frequency
b126 Releasing current
C091 Debug mode selection
C101 UP/DWN selection
C102 Reset selection
Reset f frequency matching
C103
selection
Overload advance
C111
level
C121 O zero adjustment
C122 OI zero adjustment
C123 O2 zero adjustment
(Note) < > indicate the setting range of 75 to 150kW
0.-9999./1000-6553(10000-65530)hr
00(Reverse is valid)/01(Only forward)/02(Only reverse)
00(Start reduced voltage time small)-06(Start reduced voltage time large)
00(all display)/01(each function display)/02(User setting / main setting)
00(4 quadrant mode)/01(Terminal operation)/
02(Analog input)/03(Option1)/04(Option2)
0.-200.(%)/no(Invalid) <0.-180.(%)/no(Invalid)>
0.-200.(%)/no(Invalid) <0.-180.(%)/no(Invalid)>
0.-200.(%)/no(Invalid) <0.-180.(%)/no(Invalid)>
0.-200.(%)/no(Invalid) <0.-180.(%)/no(Invalid)>
0.01-99.99/100.0-999.9/1000.-3600.(s)
0.5-15.0(kHz) Derating enable, <0-10kHz>
00(Trip history clear)/01(Data initialization)/
02(Trip history clear + data initialization)
00(Interior)/01(EC)/02(USA)
00(0Hz start)/01(Start f-equaling)
00(deceleration stop)/01(Free-run stop)
01(ON during run, After power ON, then for 5 minutes on stop is implied.)
00(invalid)/01(valid<invalid during stop>)/02(valid<valid during stop>)
00(invalid)/01(Positive temperature coefficient enable)/02 (NTC enable)
signal
0.00-99.99/100.0-400.0(Hz)
0.00*rated current-2.00*rated current(A)
00(No display)/01(Display)
00(No frequency data)/01(Keep frequency data)
00(Trip cancel during ON)/01(Trip cancel during OFF)/
02(Valid only during trip<Cancel during ON>)
00(0Hz start)/01(Start f-equaling)
notice
0.-9999./1000-6553(10000-65530)
0.-9999./1000-6553(10000-65530)
0.-9999./1000-6553(10000-65530)
SJ300 Setting range
00(Invalid)/01(Valid)
00(Invalid)/01(Valid)
00(Invalid)/01(Valid)
0.0-1000.(V)
0.0-1000.(V)
0.00-10.00(Hz)
0. - 255.
0. - 255.
0.10-9.99(Hz)
0.1-99.9
00(valid)/01(invalid)
0.0-100.0(%)
00(Always ON)/
330-380/660-760(V)
0. - 9999. ( ohm)
00(Invalid)/01(valid)
0.00-5.00(s)
0.00-5.00(s)
0.00-5.00(s)
0.00-5.00(s)
0.0-2.0*rated current(A)
1- 7
Initial data
Note
-FE/-FU/-F
0.
00
06
00
00
150.
150.
150.
150.
00
00
00
0.0
0.0
1.00
0.00
180
60
0.50
5.0 <3.0>
00
01/02/00
1.0
00
00
0.0
00
00
00
360/720
00
3000.
00
0.00
0.00
0.00
0.00
0.00
Rated
current of
inverter
00
00
00
00
Inverter
rated
current
Set on
forwarding
Set on
forwarding
Set on
forwarding