Hitachi L300P Series Service Manual page 7

Function Mode
Code Function name
s t
A061 1 frequency maximum limiter
nd
A261 2 frequency maximum limiter
s t
A062 1 frequency minimum limiter
nd
A262 2 frequency minimum limiter
A063 Jump frequency1
A064 Jump frequency Width 1
A065 Jump frequency2
A066 Jump frequency Width 2
A067 Jump frequency3
A068 Jump frequency Width 3
A069 Acceleration stop frequency
A070 Acceleration stop time
A071 PID selection
A072 PID-P gain
A073 PID-I gain
A074 PID-D gain
A075 PID scale
A076 PID feedback selection
A081 AVR selection
A082 Motor voltage selection
A085 Operation mode selection
Energy-saving response-
A086
accuracy adjustment
A092 Acceleration time2
nd
A292 Acceleration time2(2
rd
A392 Acceleration time2(3
A093 Deceleration time2
nd
A293 Deceleration time2(2
rd
A393 Deceleration time2(3
nd
A094 2 stage adjustable selection
nd
2 stage adjustable
A294
nd
selection(2 motor)
nd
A095 2 acceleration frequency
nd
2 acceleration
A295
nd
frequency(2 motor)
nd
A096 2 deceleration frequency
nd
2 deceleration frequency
A296
nd
(2 motor)
A097 Acceleration pattern selection
A098 Deceleration pattern selection
A101 OI start
A102 OI end
A103 OI start rate
A104 OI end rate
A105 OI start selection
A111 O2 start
A112 O2 end
A113 O2 start rate
A114 O2 end rate
A131 Acceleration curve constant
A132 Deceleration curve constant
b001 Retry selection
Allowable under-voltage power
b002
failure time
b003 Retry wait time
Instantaneous power failure/
b004
under-voltage trip during stop
Instantaneous power failure/
b005
under-voltage retry time
selection
b006 Open-phase selection
b007 Frequency setting to match
s t
0.00, 1 frequency lower limitter - maximum frequency(Hz)
nd
0.00, 2 frequency lower limiter-2
0.00, start frequency-maximum frequency(Hz)
0.00, start frequency-2
00(feedback : OI)/01(feedback : O)
00(ON always)/01(OFF always)/02(OFF on decelerating)
200/215/220/230/240,
00(normal operation)/01(energy-saving operation)/02(Fuzzy)
0.01-99.99/100.0-999.9/1000.-3600.(s)
motor) 0.01-99.99/100.0-999.9/1000.-3600.(s)
motor) 0.01-99.99/100.0-999.9/1000.-3600.(s)
0.01-99.99/100.0-999.9/1000.-3600.(s)
motor) 0.01-99.99/100.0-999.9/1000.-3600.(s)
motor) 0.01-99.99/100.0-999.9/1000.-3600.(s)
00(change with 2CH terminal)/01(change with setting)
00(change with 2CH terminal)/01(change with setting)
00(straight line)/01(S-curve)/02(U-curve)/03(reverse U-curve)
00(straight line)/01(S-curve)/02(U-curve)/03(reverse U-curve)
00(external start frequency)/01(0Hz)
-400.--100./-99.9-0.00-99.9/100.-400.(Hz)
-400.--100./-99.9-0.00-99.9/100.-400.(Hz)
01(small swelling)-10(large swelling)
01(small swelling-10(large swelling)
00(trip)/01(0Hz start)/02(start after equal frequency)/
03(trip after equaling frequency and deceleration stop)
00(invalid/01(valid)/02(invalid during stop and deceleration by stop
SJ300 Setting range
nd
setting maximum frequency(Hz)
nd
setting maximum frequency(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-10.00(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-10.00(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-10.00(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-60.0(s)
00(invalid)/01(valid)
0.2-5.0
0.0-3600.(s)
0.00-100.0(s)
0.01-99.99(%)
380/400/415/440/460/480
0.0-100.0
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.-100. (%)
0.-100. (%)
-100. - 100. (%)
-100. - 100. (%)
0.3-1.0(s)
0.3-100.(s)
command)
00(16 times)/01(free)
00(invalid)/01(valid)
0.00-99.99/100.0-400.0(Hz)
1- 4
Initial data
Note
-FE/-FU/-F
0.00
0.00
0.00
0.00
0.00
0.50
0.00
0.50
0.00
0.50
0.00
0.0
00
1.0
1.0
0.00
1.00
00
00/00/02
(230/400)/
(230/460)/
(200/400)
00
50.0
15.00
15.00
15.00
15.00
15.00
15.00
00
00
0.00
0.00
0.00
0.00
00
00
0.00
0.00
20.
100.
01
0.00
0.00
-100.
100.
02
02
00
1.0
1.0
00
00
00
0.00