Parts List - Central Machinery 95668 Set Up And Operating Instructions Manual

Part #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
19
20
21
22
23
26
27
28
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
44A
45
46
47
48
49
50
51
52
53
53A
54
55
56
57
58
SKU 95668 For technical questions, please call 1-800-444-3353

PARTS LIST

Description
Side Panel
Tie Bar
Rubber Foot
Philips Head Screw (M4-0.7x25)
Power Switch
Switch Lamella
Flat Washer (5mm)
Hex Nut (M4-0.7)
Carriage Bolt (M8-1.25 x 12)
Flat Washer (3/8")
Hex Nut (M8-1.25)
Philips Head Screw (M5-0.8 x 12)
Exterior Tooth Washer (5mm)
Hex Nut (M5-0.8)
Shelf
Electricity Label
Hex Nut (M8-1.25)
Flat Washer (3/8")
Strain Relief
Spindle Pulley Guard
Power Cord
Wire Cord
Flat Washer (3/8")
Hex Bolt (M8-1.25 x 12)
Table Leg
Hex Bolt (M8-1.25 x 25)
Hex Bolt (M12-1.75 x 30)
Lock Washer (12mm)
Table Support
Miter Block
Flat Washer (1/4")
Philips Head Screw (M4-0.7 x 6)
Self Tapping Screw (3.5 x 12mm)
Flat Washer (3/8")
Support Pole
Stud Bolt
Anti-Kickback Pin
Miter Bar
Aluminum Alloy Fence
Right Fence Lid
Left Fence Lid
Miter Gauge Body
Plastic Handle
Pointer
Self Tapping Screw (M3 x 15)
Tension Pin (2 x 16mm)
Carriage Bolt (M6-1 x 35)
Knob (M6-1.0)
Work Table
Table Insert (1-3/8" Hole)
Table Insert (1-3/4" Hole)
Carriage Bolt (M6-1 x 35)
Knob (M6-1.0)
Taper Pin (8 x 75mm)
Fence Body (Right)
Clamp Stud
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Part # Description
59 Fence Body (Left)
60 Fence
61 Lock Handle
62 Flat Washer (1/2")
63 Flat Washer (3/8")
64 Knob (M8-1.25)
65 Lock Washer (1/2")
66 Hex Bolt (M12-1.75 x 20)
67 Adjusting Screw Stud
68 Hand Knob
69 Roll Pin (3 x 20)
70 Philips Head Screw (M6-1 x 12)
71 Half Collar
72 Adjusting Shaft
73 Flat Washer (1/2")
74 Hex Nut (M12-1.75)
75 Hex Bolt (M8-1.25 x 12)
76 Flat Washer (3/8")
77 Hold Down Bar
78 Philips Head Screw (M4-0.7 x 10)
79 Hex Post
80 Hex Nut (M8-1.25)
81 Flat Washer (3/8")
82 Mounting Bracket
83 Hand Knob
84 Hex Nut (M4-0.7)
85 Ring Guard
86 Hex Bolt (M8-1.25 x 30)
87 Housing Bracket
88 Clamp Sleeve (Left)
89 Stuff Ring
90 Roll Pin (3 x 20mm)
91 Lock Bar
92 Hand Knob
93 Roll Pin (3 x 20mm)
94 Lock Nut
95 Hex Bolt (M12-1.75 x 30)
96 Upper Spindle Nut
97 Safety Washer
98 Rub Collar (1/2" x 1-3/16" x 3/16")
99 Rub Collar (1/2" x 1-3/16" x 1/4")
100 Rub Collar (1/2" x 1-3/16" x 3/8")
101 Cutter Spindle
102 Collet Nut
103 Collet
104 Collet
105 Spindle
106 Key (4 x 4 x 20mm)
107 Interior Retaining Ring (47mm)
108 Wave Washer (45mm)
109 Ball Bearing
110 Spindle Housing
111 Ball Bearing Sleeve
112 Ball Bearing
113 Spindle Pulley
114 Lower Spindle Nut
115 Bearing Cone
116 Coil Spring
117 Set Screw (M8-1.25 x 8)
118 Spring Collar
NOTE:
PAGE 27