Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Milesight UF51
Summary of Contents for Milesight UF51
- Page 1 5G CPE UF51 Quick Start Guide...
- Page 2 The related documents are available on Milesight website: https://www.milesight-iot.com Declaration of Conformity UF51 are in conformity with the essential requirements and other relevant provisions of the CE, FCC, and RoHS. © 2011-2022 Xiamen Milesight IoT Co., Ltd. All rights reserved.
- Page 3 Revision History Date Doc Version Description July 28, 2021 V 1.0 Initial version Update cellular pictures Dec. 1, 2021 V 1.1...
-
Page 4: Table Of Contents
Contents 1. Packing List................................5 2. Hardware Introduction............................6 2.1 Overview................................6 2.2 Dimensions..............................6 2.3 Serial & IO & Power Pinouts......................... 7 2.4 LED Indicators..............................7 2.5 Reset Button..............................8 3. Power Supply................................9 4. Hardware Installation............................10 4.1 SIM Card Installation...........................10 4.2 Waterproof Cover &... -
Page 5: Packing List
1. Packing List Before you begin to install the UF51, please check the package contents to verify that you have received the items below. 1 × 8-Pin Pluggable 1 × UF51 1 × Ethernet Cable 1 × PoE Injector Terminal 1 ×... -
Page 6: Hardware Introduction
2. Hardware Introduction 2.1 Overview LED Indicator Area STATUS: Power & System Indicator 5G: Cellular Indicator Waterproof Connector SIM Slot Reset Button Vent Plug LAN2 Port Bracket Mounting Screws Serial & IO & Power Interface LAN1/WAN Port (PoE PD) 2.2 Dimensions (mm) -
Page 7: Serial & Io & Power Pinouts
2.3 Serial & IO & Power Pinouts RS232 Power Description /RS485 Digital Input Ground Negative Positive (9-48V) Common Ground Digital Output RS232-RXD RXD/B RS485-B RS232-TXD TXD/A RS485-A 2.4 LED Indicators Indication Status Description The power is switched off Power & Orange Static: The system is startup STATUS... -
Page 8: Reset Button
2.5 Reset Button Description Function STATUS & 5G LED Action Static Press and hold the reset button for more than 5 seconds. Reset Static → Blinking Release the button and wait. The device resets to factory default. Off → Static Green... -
Page 9: Power Supply
Both power supplies can’t be used at the same time. PoE Supply: Follow the below picture to provide power supply via PoE injector. Besides, UF51 can also be powered by PoE switch. DC Supply: Connect the DC power cable to terminal block, then connect the terminal block to DC... -
Page 10: Hardware Installation
4.2 Waterproof Cover & Ethernet Cable Installation If you need to use UF51 outdoors, the waterproof cover and cable gland should be installed under the bottom of the device. A. Install the rubber ring into the bottom of the device. Note that the round part needs to face the gap of bottom when installing, otherwise it may cause waterlogged. -
Page 11: Device Installation
Bottom cover can be fixed with the device via the wiring behind the cover. 4.3 Device Installation UF51 supports multiple installation methods like desktop, wall mounting, pole mounting, etc. Before you start, make sure that your SIM card has been inserted and all cables have been installed. -
Page 12: Pole Mounting
Note: The connecting lines of adjacent points are at right angles. B. Drill four holes with a depth of 32 mm by using your drill with a 6 mm drill bit on the positions you marked previously on the wall. C. -
Page 14: Log In The Web Gui
5. Log in the Web GUI UF51 provides web-based configuration interface for management. If this is the first time you configure the device, please use the default settings below: IP Address: 192.168.1.1 Username: admin Password: password 5.1 Wireless Access A. Enable Wireless Network Connection on your computer and search for access point “Router_******” to connect it. -
Page 15: Wired Access
5.2 Wired Access Connect PC to LAN port of UF51 directly. The following steps are based on Windows 10 operating system for your reference. A. Go to “Control Panel” → “Network and Internet” → “Network and Sharing Center”, then click “Ethernet”... - Page 16 C. Open a Web browser on your PC (Chrome is recommended), type in the IP address 192.168.1.1, and press Enter on your keyboard. D. Enter the username, password, and click "Login". If you enter the username or password incorrectly more than 5 times, the login page will be locked for 10 minutes.
- Page 17 F. After you login the Web GUI, you can view system information and perform configuration on the device.
-
Page 18: Network Configuration
6. Network Configuration This chapter explains how to connect UF51 to network via WAN connection, Wi-Fi or cellular. 6.1 Ethernet WAN Configuration A. Go to “Network > Interface > WAN” to select connection type and configure WAN parameters, click “Save & Apply” button to make the changes take effect. - Page 19 B. Go to “Network > Interface > Link Failover” to enable Cellular and rise link priority. C. Click to configure ICMP ping detection information.
-
Page 20: Wi-Fi Configuration
SIM has dialed up successfully. E. Open your preferred browser on PC, then type any available web address into address bar and see if it is able to visit Internet via UF51. 6.3 Wi-Fi Configuration A. - Page 21 D. Go to “Network” → “Interface” → “Link Failover” to enable WLAN. E. Go to “Status”→”WLAN” to check Wi-Fi status. If it shows “Connected”, it means the device connects to Wi-Fi successfully. [END]...
Need help?
Do you have a question about the UF51 and is the answer not in the manual?
Questions and answers