Advertisement
Quick Links
NRS Installation Manual
Standard / EU Spec.
Chair Mount Type
KAZE
(AY-KFPLU AY-NRS1 is shown.)
Installer: Read through this installation manual to ensure proper installation.
Leave this manual to the owner after installation completed.
Owner: Keep this manual in a safe place for your future reference.
OTO
(AY-OLL AY-NRS1 is shown.)
Separate Type
(AY-NRS2B-W is shown.)
Advertisement
Related Manuals for Takara Belmont KAZE AY-KFPLU AY-NRS1
Summary of Contents for Takara Belmont KAZE AY-KFPLU AY-NRS1
- Page 1 NRS Installation Manual Standard / EU Spec. Chair Mount Type KAZE (AY-OLL AY-NRS1 is shown.) (AY-KFPLU AY-NRS1 is shown.) Separate Type (AY-NRS2B-W is shown.) Installer: Read through this installation manual to ensure proper installation. Leave this manual to the owner after installation completed. Owner: Keep this manual in a safe place for your future reference.
-
Page 2: Before Installation
Definition of markings These markings indicate important information to avoid personal injuries, or property damages against you or your customers by using this product correctly. All instructions are important for safety operation. Please be sure to observe them. CAUTION This mark warns the user that "improper use may cause personal injuries or material damages". -
Page 3: Requirements For Use
Requirements for Use Requirements for hot/cold water supply • Drinking water (Non-drinkable well water, or water including sand or rust are not approved for use.) Water for use • If the water hardness is 80 ppm or more, treat the water with a water softener in order to prevent scale clogging of the equipment. - Page 4 Packing Material (Standard spec.) Shampoo unit side Cover set Base cover • Shampoo unit • Stop valve Rear cover Front cover Chair mount frame Chair mount (Not provided for separate type) frame cover (For chair mount type only) Set of screws for cover •...
- Page 5 Packing Material (EU spec.) Shampoo unit side Cover set • Shampoo unit Base cover • Stop valve Rear cover Front cover Chair mount frame (Not provided for separate type) Chair mount frame cover (For chair mount type only) Set of screws for cover •...
-
Page 6: Anchoring Procedure
Installing Shampoo Unit (Standard spec.) Marking Lay the accessory pattern paper on the floor at the installation position referring to the raising positions of cold/hot water supply pipes and tape the pattern paper. Mark the floor with a pencil at the positions of the shampoo unit base and the screw holes. Remove the pattern paper. - Page 7 Attaching the chair mount frame cover and frame receiver cover. Attach the chair mount frame cover on the chair mount frame. Chair mount frame cover Place the frame receiver cover on the chair mount frame and press it firmly to the end. Notes in moving the shampoo unit •...
- Page 8 Mounting Chair (Standard spec.) Attaching to the chair mount frame. Place the chair on the chair mount frame with aligning the centers of the mount pipes (4 pipes) in the back of the chair with the lines on the side of the chair mount bracket of the chair mount frame.
- Page 9 Installing Shampoo Unit (EU spec.) Marking Lay the accessory pattern paper on the floor as a template at the installation position referring to the raising positions of cold/hot water supply pipes and tape the pattern paper. Trace the positions of the shampoo unit base and the screw holes onto the floor. Remove the pattern paper.
- Page 10 Fixing the shampoo unit. Attach the shampoo unit to the base bracket securely. Detach the four screws on the shampoo unit. Attach the chair mount frame to the shampoo unit. Then fix the shampoo unit temporarily with the screws detached in Fix the chair mount frame on the floor at the marked position with the chair mount frame packing inserted.
- Page 11 Mounting Chair (EU spec.) Attaching to the chair mount frame. Place the chair on the chair mount frame with aligning the centers of the mount pipes (4 pipes) in the back of the chair with the lines on the side of the chair mount bracket of the chair mount frame.
- Page 12 Plumbing (Standard / EU spec.) Attaching the flexible pipe. Clean the piping area of plumbing refuses such as dust, sand and oil first. Attach the stop valves to the cold water supply pipe and the hot water supply pipe. And then attach the flexible pipes together with the accessory packing rings to the stop valves.
- Page 13 Attaching Covers Attaching the base cover. Attaching the rear cover. Attach the base cover to the unit and fix it with Attach the bottom of the rear cover to the unit two screws. first. Then fix the rear cover with two screws to allow the mixing hose to pass through the rear cover hole.
- Page 14 Plumbing Drawing (Standard spec.) Chair Mount Type KAZE Center of piping (295) (1180) 1340 (with U-footrest) 1480 (with W-footrest) * The dimension in parentheses is a reference value. (AY-KFPLW AY-NRS1 is shown.)
- Page 15 Center of pipe (1180) 1515 (with leg rest) * The dimension in parentheses is a reference value. (AY-OLL AY-NRS1 is shown.) * The distance between the end of the leg rest and the wall or the furniture shall be at least 650 mm.
- Page 16 Separate type Center of piping (AY-NRS2 is shown.)
- Page 17 Plumbing Drawing (EU spec.) Chair Mount Type KAZE Mount bracket Center of pipe (295) (1200) 1360 (with U-footrest) 1500 (with W-footrest) * The dimension in parentheses is a reference value. (AD-KFPLW AY-NRS1 is shown.)
- Page 18 Mount Center of pipe bracket (1200) 1535 (with leg rest) * The dimension in parentheses is a reference value. (AD-OLL AY-NRS1 is shown.) * The distance between the end of the leg rest and the wall or the furniture shall be at least 650 mm.
- Page 19 Separate type Center of piping ( AY- NR S 2 i s sh own .)
-
Page 20: Checking After Installation
After Installation (Standard / EU spec.) Checking after installation. Check the following points. CAUTION In order to prevent accidents during operation, be sure to check that All bolts and screws, etc. are attached. The shampoo unit and chair are securely attached. If there is a slack in the shampoo unit or the chair, check if the bolts at the attaching portions are fastened tightly. - Page 21 Layout Drawing (Standard spec.) Notes on the floor finished with tiles or glass In the case where the floor is finished with tiles etc., screwing bolts into the floor when installing the shampoo unit may cause a crack on the floor surface. Change the material of the floor of the installation position to plywood, mortar, etc.
- Page 22 Layout Drawing (EU spec.) NRS EU SPEC FULL-SCALE PATTERN PAPER The designed piping position shows the standard piping position. Distance to the wall or the furniture, etc.: Min. 760 mm (including working space 600 mm) Distance to the wall or the furniture, etc.: Min.
- Page 23 MEMO...
- Page 24 Memo TAKARA BELMONT CORPORA TION 1-1, Higashi-shinsaibashi 2-Chome ,Chuo-ku,Osaka,J apan TEL. : (06) 6213-5945 TELEF AX : (06) 6212-3680 Pr inted in J apan 0508. BAEA44A0 05.10...