Basic Operation - Gaggenau AC250121 User Manual And Installation Instructions

To cancel the setting, press ⁠ .
8 Basic operation
8.1 Switching on the appliance
Requirement: Align the remote control as precisely as
possible to the infrared receiver for the LED display.
Press to switch on the appliance.
▶
a The appliance starts at fan setting 2.
a The LED for the set fan setting lights up in the LED
display.
8.2 Switching off the appliance
Switch the appliance off when you are not using it.
Press to switch the appliance off.
▶
a The appliance switches off. Any functions currently
in progress are cancelled.
8.3 Selecting a fan setting
Press or ⁠ .
▶
a The LED for the set fan setting lights up in the LED
display.
8.4 Switching on intensive mode
If particularly strong odours or vapours develop, you
can use intensive mode.
so oft drücken, bis in der LED-Anzeige die LED 4
1.
für die Intensivstufe 1 leuchtet.
so oft drücken, bis in der LED-Anzeige die LED 5
2.
für die Intensivstufe 2 leuchtet.
a After approx. 6 minutes, the appliance automatically
switches to fan setting 3.
8.5 Switching off intensive mode
To select a fan setting of your choice, press
▶
8.6 Switching on intermittent ventilation
With interval ventilation, the ventilation switches on for
approx. 6 minutes every hour.
Note: In the Home Connect app, you can set the time
and fan setting individually.
Press ⁠ .
▶
a In the LED display, LED 6 flashes continuously, the
LED for the selected fan setting lights up on the ap-
pliance.
a As soon as the ventilation time ends, the LED for
the fan setting you have selected goes out. LED 6
continues to flash.
8.7 Switching off interval ventilation
Press ⁠ .
▶
1
Depending on the appliance specifications
a A signal tone sounds as soon as the selected set-
ting is saved.
8.8 Switch on automatic mode
The optimum fan setting is set automatically using a
sensor.
Press ⁠ .
▶
a In the LED display, LED 6 lights up for automatic
mode.
8.9 Switch off automatic mode
Press ⁠ .
▶
a The appliance switches to the fan setting that was
previously set.
a The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a Automatic mode runs for a maximum of four hours.
8.10 Intermittent ventilation
With interval ventilation, the ventilation system switches
on and off in the selected setting for the selected time.
Note: This function is only available via a mobile device
with the Home Connect app.
If the interval ventilation is switched on, LED 6 continu-
ously flashes in the LED display for the interval ventila-
tion and the LED for the selected fan setting lights up.
As soon as the ventilation time ends, the LED for the
fan setting you have selected goes out. LED 6 contin-
ues to flash.
8.11 Sensor control
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
⁠ .
pending on the setting of the sensor sensitivity, the op-
timum fan setting is automatically switched on.
If the sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
¡ Default setting: Fan setting 3
¡ Lowest setting: Fan setting 1
¡ Highest setting: Fan setting 5
8.12 Setting the sensor control
Requirement: The appliance is switched off.
Press and hold
1.
2. Press
To cancel the setting, press ⁠ .
To save the setting, press and hold
3.
prox. 3 seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
1
and for approx. 3 seconds.
or to change the setting.
Basic operation en
1
1
1
and for ap-
31