3.7 Installing SATA Hard Drive on Top Side .............. 55 3.8 Installing PCI/PCIe Add-on Card ................56 3.9 Assembling Top Cover ....................60 3.10 Installing SATA Hard Drives at Front Panel ..........63 3.11 Installing SIM Card .................... 65 Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 3
4.7.1 Save Changes and Exit ..................95 4.7.2 Discard Changes and Exit ..................95 4.7.3 Save Changes and Reset ..................95 4.7.4 Discard Changes and Reset .................. 95 4.7.5 Save Changes ......................95 Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 4
6.5.1 PB-3000E-MEC-COM-M212 Set ................. 145 6.5.2 PB-3000E-MEC-USB Set ..................148 6.5.3 PB-3000E MEC-LAN Set ..................151 6.6 Installing External FAN ................... 154 6.7 Installing Internal FAN (For PB-32xx only) ............156 Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Product Warranty Statement Warranty Spectra products are warranted by Spectra GmbH & Co. KG to be free from defect in materials and workmanship starting from the date of purchase by the original purchaser. The actual warranty period of Spectra products vary with product categories. During the warranty period, we shall, at our option, either repair or replace any product that proves to be defective under normal operation.
Page 7
Before sending your product in, you will need to fill in a Spectra RMA Request Form and obtain a RMA number from us. Please go to www.spectra.de/RMA to fill in this form. Our staff is available at any time to provide you with the most friendly and immediate service.
Technical Support and Assistance 1. Visit the Spectra website at www.spectra.de where you can find the latest information about the product. 2. Contact our technical support team or sales representative for technical support if you need additional assistance. Please have following information ready before you call: ...
14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. 15. Equipment intended only for use in a RESTRICTED ACCESS AREA. Spectra GmbH & Co. KG User Manual sales@spectra.de...
1.1 Overview The Spectra PowerBox 3000E series is a powerful embedded computer and brings unrivalled performance. It has versatile functionalities and rich industrial I/O. And most importantly, it has one PCI/PCIe expansion capability (PowerBox 31E and PowerBox 32E). Equipped with CMI, CFM, MEC modular expansion, customization for additional I/O or other functionality to fulfill different applications couldn’t be easier.
Page 13
Rugged Reliability Against Rigorous Environments The Spectra PowerBox 3000E’s fanless and cableless industrial- grade design can withstand rigorous environments. Its unique thermal design supports an extended operating temperature range fom -40°C to 70°C. It has also passed stringent industry standards, including MIL-STD-810G military standard (pending) and EN50155 (EN 50121-3-2 only) for rolling stock environments.
Optional CMI modules for I/O expansion Optional CFM modules for ignition sensing & PoE Wide operating temperature -40°C to 70°C MIL-STD-810G military standard and EN50155 (EN 50121-3-2 only) Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
1x VGA Connector (1920 x 1200 @60Hz) Audio Audio Codec • Realtek® ALC888, High Definition Audio Line-out • 1x Line-out, Phone Jack 3.5mm Mic-in • 1x Mic-in, Phone Jack 3.5mm Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 19
(Support Smart Fan by BIOS) • Support Power Ignition Sensing Function with Delay Time Management and Power Ignition Sensing Selectable 12V/24V (With Optional CFM Module) Clear CMOS Switch • 1x Clear CMOS Switch Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 20
• Protection Type: shut down operating voltage, re-power on at the present level to recover Over Current Protection • Surge Protection • 3.84 kV (impedance 12 ohm 1.2/50us waveform) Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 21
Supports by project * Product Specifications and features are for reference only and are subject to change without prior notice. For more information, please refer to the latest product datasheet from our website. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Used to set up IGN function Used to connect USB 3.2 Gen2/3.2 Reset Button Gen1/3.0/2.0/1.1 device Used to reset the system HDMI Used to connect the system with HDMI monitor Spectra PowerBox 30E* Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 23
Spectra PowerBox 31E* Spectra PowerBox 32E* Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 24
Used to connect USB 2.0/1.1 device Universal I/O Bracket LAN1, LAN2 Used to customized I/O output Used to connect to local area network Spectra PowerBox 30E* Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 25
Spectra PowerBox 31E* Spectra PowerBox 32E* Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
ON (Default) ON (Default) COM1 Location Function DIP5 DIP6 0V(RI) ON (Default) ON (Default) COM2 SW2: Super CAP Switch Location Function DIP1 DIP2 Enabled ON (Default) Super ON (Default) Disabled Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 35
AT_ATX: AT / ATX Power Mode Switch Switch Definition Left AT Power Mode Right ATX Power Mode (Default) CLR_CMOS1: Clear BIOS Switch Definition 1-2 (Left) Normal Status (Default) 2-3 (Right) Clear BIOS Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 39
Do not apply power to this connector! This port is used to connect a SWITCH! FAN1: CPU Smart Fan Connector Connector Type: Terminal Block 1X4 4-pin, 3.5mm pitch Definition +12V FAN_IN FAN_PWR Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 40
DATA - DATA + DC_IN2: 3 PINs DC 9‐48V power input with power ignition connector Connector Type: Terminal Block 1x3 3-pin, 5.0mm pitch Definition +9~48VIN Ignition (IGN) 1 2 3 Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 41
75°C < System Temp Blinking Red Data activity Yellow HDD LED No activity GPIO activity Green GPIO LED No activity The TEMP LED is only available when IGN module is installed. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 42
Definition Steady Green 1 Gbps Network Link Steady Orange 100 Mbps Network Link 10 Mbps Network Link Act LED Status Definition Blinking Yellow Data Activity Steady Yellow No Activity Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
1. Turn over the unit to have the bottom side face up, loosen the 6 screws on the bottom cover and place them aside for later use. 2. Remove the bottom cover from the chassis. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 45
3. Unscrew the 2 screws at the rear bezel as indicated and place them aside for later use. 4. Loosen the 4 screws. Pull out the 4 latches as marked. 5. Lift up the unit vertically by holding the front and rear panel. Spectra GmbH & Co. KG User Manual sales@spectra.de...
6. Turn over the body of the unit and place it gently. 3.2 Installing CPU Locate the CPU socket. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 47
Align the notches on the CPU with protrusions on the socket. Hold the CPU by the edges and put on the CPU gently. Press down the socket lever to lock the CPU. Spectra GmbH & Co. KG User Manual sales@spectra.de...
4 screws. 3.3 Installing SO-DIMM 1. Turn the system to the bottom side. Unscrews the 4 screws and remove the bracket. 2. Locate two SO-DIMM sockets at the bottom. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 49
4. Press down the module until the retaining clips snap back in place. Upper socket Lower socket 5. Put the cover back and fix the cover with 4 screws. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
(a) Half Size Mini-PCIe Tilt a Mini PCIe card at a 45-degree angle and insert it to the socket until the golden finger connector of the card seated firmly. 45° Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 51
Press the card down and secure it with 2 screws. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
2. Tilt the M.2 M Key card at a 45-degree angle and insert it to the socket until the golden finger connector of the card seated firmly. 45° 3. Press the card down and secure it with the screw. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
1. Remove the antenna rubber cover on the rear panel. 2. Penetrate the antenna jack through the hole. 3. Put on the washer and fasten the nut of antenna jack. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 54
4. Assemble the antenna and antenna jack together. 5. Attach the RF connector of the cable’s another end onto the card. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
4 screws to assemble HDD and HDD bracket together. 3. Turn over the HDD bracket. Connect the HDD bracket to the SATA connector and fasten the 3 screws. Spectra GmbH & Co. KG User Manual sales@spectra.de...
3.8 Installing PCI/PCIe Add-on Card (For PB-31xx and PB-32xx only) The applicable riser cards for Spectra PowerBox 3000E series are listed in the following table. Model No. Description Compatible Model RSC-E16 Riser Card with 1 x PCIex16 Slot PowerBox-31xx RSC-PI...
Page 57
3. Assemble the riser card with extension bracket together and fasten with the 4 screws. 4. (1) Loosen the screw(s) to remove I/O bracket(s). (2) Loosen the screws halfway to allow the card retainer to be adjustable. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 58
5. (1) Insert PCI(e) add-on card to the slot. (2) Fasten the screw to secure it 6. (1) Push the card retainer forward to against the edge of the add-on card. (2) Fasten the screws to fix the card retainer. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 59
7. Locate the riser card slot on bottom side of system. 8. Install the module assembled in step 6 into the riser card slot, and fasten the 4 screws to secure Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
3.9 Assembling Top Cover 1. Make sure the notch on the chassis and the front bezel of the unit body are on the same side. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 61
2. Lift the body of the unit, make sure that the front and rear panels are in the chassis groves, and then assemble the body into the chassis. 3. Push into the 4 latches as indicated and fasten the 4 screws. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 62
4. Fasten the 2 screws at rear panel. 5. Be sure to align the grooves with front and rear panels. Put the bottom cover back on and fasten the 6 screws to fix the cover. Spectra GmbH & Co. KG User Manual sales@spectra.de...
1. Loosen the two screws to remove the cover plate of maintenance zone. 2. Loosen the screw to remove the HDD bay cover bracket. 3. Pull the rotating arm and pull the HDD bracket out of system. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 64
5. Align the HDD bracket with the entrance of HDD bay. Insert the HDD bracket and push it until the HDD connector is fully inserted into the SATA slot. 6. Place the rotating arm back and fasten the screw(s). Spectra GmbH & Co. KG User Manual sales@spectra.de...
2. Locate the SIM card slot at front side and insert a SIM card into a SIM slot with the gold contacts facing up. Please pay attention to the insert orientation as illustrated. 3. Fix the cover plate of maintenance zone by fastening the two screws. Spectra GmbH & Co. KG User Manual sales@spectra.de...
1. Loosen the two screws to remove the cover plate of maintenance zone. 2. Locate the removable CMOS Battery and loosen the screw. 3. Pull out the CMOS battery bracket with assistance of a tweezer. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 67
"-" side and pull the metal tab backwards to make the battery fully installed in the slot. 6. Insert the battery bracket firmly. 7. Fasten the screw. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 68
8. Fix the cover plate of maintenance zone by fastening the two screws. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
3.13 Installing Wall Mount Spectra PowerBox 3000E series offers wall mount kit that customers can install the system on the wall in a convenient and economical way. 1. The mounting holes are at the bottom side of the system. Use the provided 8 screws to fasten the bracket and the system together.
Page 70
2. Fasten the screws through the bracket mounting holes to mount the system onto the wall. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
3. Fasten the two screws to fix the phoenix contacts. In formal use, please use new Phoenix contacts and make sure the screws are tightened to avoid poor connection. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Then you can use the control keys to enter values and move from field to field within a sub-menu. If you want to return to the main menu, just press the <Esc >. Spectra GmbH & Co. KG User Manual sales@spectra.de...
4.2.1 System Date Set the date. Please use <Tab> to switch between date elements. 4.2.2 System Time Set the time. Please use <Tab> to switch between time elements. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
With virtualization, one computer system can function as multiple virtual systems. ■ Active Process Cores [All] Allows users to choose the number of active processor cores. Configuration options: [All] [1] [2] [3] [4] [5] Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Enables or disables for Hyper-Threading Technology. 4.3.2 Power & Performance ■ SKU Power Config [Auto] Allows users to choose the upper limit of CPU power. Configuration options: [Auto] [35W] 4.3.3 SATA Configuration Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Serial ATA Port 4 Port 4 [Enabled] Enables or disables SATA Port 4. Serial ATA Port 5 Port 5 [Enabled] Enables or disables SATA Port 5. 4.3.4 PCH-FW Configuration Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Allows users to enable or disable ME firmware image re-flash function. 4.3.5 Trusted Computing ■ Security Device Support [Enable] Allow users to enable or disable Security Device Support function. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
■ Physical Presence Spec Version [1.3] Allows users to select which mode Physical Presence Spec Version will operate. Configuration options: [1.2], [1.3] 4.3.6 ACPI Settings This item allows users to configure ACPI settings. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
4.3.7 F81866 Super IO Configuration The screen allows users to select options for the Super IO configuration, and change the value of the selected option. ■ Serial Port 1~4 Configuration Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
User can set a value in the range of 0 to 255. 4.3.8 Hardware Monitor These items display the current status of all monitored hardware devices/ components such as voltages and temperatures. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 82
Allows users to setting external smart fan parameters. ■ Internal Smart Fan Function [Enabled] Enables or disables internal smart fan function. ■ Internal Smart Fan Configuration Allows users to setting internal smart fan parameters. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
This item allows users to change the way to wake system from S5 state. [Fixed Time]: Set the specified time (HH:MM:SS) to wake system. [Dynamic Time]: Set the increase time from current time to wake system. 4.3.10 Serial Port Console Redirection Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Allows users to select which Output Interface to display under BIOS mode. The options shown in this item depend on the displays connected to the system. [EDP1]: VGA [HDMI1]: HDMI [DP2]: DP (Front Panel) [DP3]: DP (Rear Panel) 4.3.12 USB Configuration Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
■ USB Mass Storage Driver Support [Enabled] Enables or disables support for USB mass storage devices. 4.3.13 Network Stack Configuration ■ Network Stack [Disabled] Enables or disables UEFI Network Stack. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
[UEFI]: Enables UEFI option ROM only. [Legacy]: Enables legacy option ROM only. ■ Video [UEFI] Controls the execution of UEFI and Legacy Video option ROM. [Do not launch]: Disables option ROM execution. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
The screen allows users to select options for the NVMe configuration, and change the value of the selected option. If there is NVMe Device detected, the options will show as the NVMe Device is found. Spectra GmbH & Co. KG User Manual sales@spectra.de...
4.4 Chipset Setup This section allows you to configure chipset related settings according to user’s preference. 4.4.1 System Agent (SA) Configuration Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 89
[Auto], it will detect by BIOS. Configuration options: [Auto] [Disabled] [Enabled] ■ VT-d [Enabled] This item allows users to enable or disable Intel® Virtualization Technology for Directed I/O (VT-d) function. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
PCI Express Root Port [Enabled] Allows you to enable or disable the PCI Express Port. PCIe Speed [Auto] Allows you to select PCI Express interface speed. Configuration options: [Auto] [Gen1] [Gen2] [Gen3]. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 91
Allows you to enable or disable the PCI Express Port. PCIe Speed [Auto] Allows you to select PCI Express interface speed. Configuration options: [Auto] [Gen1] [Gen2] [Gen3]. ■ HD Audio Configuration HD Audio [Enabled] Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 92
(G3 state). [Always on]: Enters to power on state. [Always off]: Enters to power off state. [Keep last state]: Enters to the last power state before a power failure. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Allows users to select the power-on state for keyboard NumLock. 4.6.3 Quiet Boot [Disabled] Allows users to enable or disable Quiet Boot function. 4.6.4 Fast Boot [Disabled] Allows users to enable or disable Fast Boot function. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
This item allows users to save the changes done so far as user defaults. 4.7.9 Restore User Defaults This item allows users to restore the user defaults to all the options. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 98
Following is an example to enable configuration and to disable configuration by using debug. -o 4e 87 -o 4e 87 (enable configuration) -o 4e aa (disable configuration) 5.1.1.4 Relative Registers To program the F81866A configuration registers, see the following configuration procedures. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 99
Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 100
Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 101
Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 102
// Set (bit 0~7) = 0 to select GP 70~77 as Input mode. <Input Value> WriteByte(AddrPort, 0x82) // Select configuration register 82h ReadByte(DataPort, Value) // Read bit 0~7 (0xFx)= GP70 ~77 as High. <Leave the Extended Function Mode> WriteByte(AddrPort, 0xAA) Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 103
5.1.1.5.3 Control of GP70 to GP77 & GP30 to GP37 (DI1 ~ DI16) #define AddrPort 0x4E #define DataPort 0x4F <Enter the Extended Function Mode> WriteByte(AddrPort, 0x87) WriteByte(AddrPort, 0x87) // Must write twice to entering Extended mode Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 104
// Read bit 0~7(0xFx)= GP70~77 as High <input Value> WriteByte(AddrPort, 0xC2) // Select configuration register C2h ReadByte(DataPort, Value) // Read bit 0~7(0xFx)= GP30~37 as High <Leave the Extended Function Mode> WriteByte(AddrPort, 0xAA) Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 105
// Set (bit 0~7) = 1 to select GP 40~47 as Output mode <Output Value> WriteByte(AddrPort, 0x89) // Select configuration register 89h WriteByte(DataPort, Value) // Set bit 0~7=(0/1) to output GP 80~87 as Low or High <Output Value> Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 106
// Select configuration register 60h (High Byte address) WriteByte(DataPort, (0x0A)) WriteByte(AddrPort, 0x61) // Select configuration register 61h (Low Byte address) WriteByte(DataPort, (0x00)) <Leave the Extended Function Mode> WriteByte(AddrPort, 0xAA) default GPIO Port base address is 0xA00h Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 109
(0xA09) 5.1.1.8 DIO I/O Port Address (Default Address 0xA00) Pin Definition Data Bits Digital Input I/O Port Address 0xA03 Pin Definition Data Bits Digital Output I/O Port Address 0xA02 Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 110
DI13 DI12 DI11 DI10 Data Bits Digital Input I/O Port Address 0xA09 Pin Definition DO16 DO15 DO14 DO13 DO12 DO11 DO10 Data Bits Digital Output I/O Port Address 0xA010 Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
DO Signal have to pull up resistor to XCOM+ for external device, the ‐ resistance will affect the pull up current Signal High Level: Pull up resistor to XCOM+ ‐ Signal Low Level: = XCOM- ‐ Sink Current: 1A (Max) ‐ Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Following is examples to enable configuration and to disable configuration by using debug. Example to enable configuration: -o 4e 87 -o 4e 87 Example to disable configuration: -o 4e aa Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 116
To program the F81866A configuration registers, see the following configuration procedures. Following is an example to Select GPIO device by LDN(index 07h) using debug. -o 4e 07 -o 4f 06 Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 117
Because we need to set bit0 to 1 for GPIO10 output , thus made the new value to 01 . Second step,write the new value 01 to set bit0 with output mode -o 4e e0 -o 4f 01 Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 118
Second step: write the new value 01 to set bit0 for control output -o 4e e1 -o 4f 01 ( Note, the bit0 (GPIO10) can be set 0 or 1 ) Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 119
WriteByte(AddrPort, 0xE1) // Select configuration register E1h WriteByte(DataPort, Value | 0x01 ) // Set (bit 0) =1 to output GPIP10 as High <Leave the Extended Function Mode> WriteByte(AddrPort, 0xAA) Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 120
// Must write twice to enter Extended mode <Select Logic Device> WriteByte(AddrPort, 0x07) WriteByte(dataPort, 0x06) // Select logic device 06h WriteByte(AddrPort, 0x60) // Select configuration register 60h (High Byte address) WriteByte(DataPort, (0x0A)) Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
I/O Port data register address = Base address + 7 = 0xA07 = LED (Base address +7) (0xA07) 5.4 GPIO LED Status Definition GPIO LED Type Status LED Color GPIO activity Green GPIO LED No activity Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Default setting of Pin1 to Pin4 is OFF / OFF / OFF / OFF. 24V_12V_1:IGN Module Voltage Mode Setting Switch 12V / 24V Car Battery Switch Switch Definition Left 12V Car Battery Input Right 24V Car Battery Input (Default) Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
2. Attach the PB-LAN bracket, and fasten the 2 hex nuts to fix it as indicated. 3. Locate the connector(s) of PB-LAN module on top side of system. BTB_FH2 BTB_FH4 Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
PB-300E-LAN-M12 Set Loosen the 2 hex nuts from back side of front bezel. Remove the front bezel. Attach the PB-LAN-M12 bracket, and fasten the 2 hex nuts to fix it as indicated. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 129
5. Penetrate the PB-LAN-M12 ports through the holes on the bracket. Insert the CMI module vertically into the female connector on system’s mainboard until it’s connected firmly and fasten 4 screws to fix it. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Fasten the four hex rings to fix the cover plate. 6.2.3 PB-3000E-LAN-XM12 Set Hex washers M12 I/O bracket Hex rings Rubber rings Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 131
2. Loosen the 2 hex nuts from back side of front bezel. Remove the front bezel. 3. Locate the connector(s) of PB-LAN-M12 module on top side of system. BTB_FH2 BTB_FH4 Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 132
4 screws to fix it. 4. Attach the assembled M12 I/O bracket on to the system, and fasten the hex nuts to fix it. 5. Put on the rubber rings to the four M12 LAN ports. Spectra GmbH & Co. KG User Manual sales@spectra.de...
When entering BIOS, get to Chipset > PCH-IO Configuration page, and change the [BTB_FH2 Mode Selection] setting from default mode [4x1] to mode [1x4]. Loosen the 2 hex nuts from back side of front bezel. Remove the front bezel. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 134
Locate the chip place on the PB-3000E-10GLAN module marked by red square. Paste the thermal pad on it carefully. Before putting on the heatsink (in the next step), please make sure the protective film on the Thermal Pad has been removed! Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 135
4 screws to fix it. Paste the thermal pad onto the heatsink carefully. Before assembling the system’s chassis cover, please make sure the transparent protective films on the Thermal Pads have been removed! Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
1. Loosen the 2 hex nuts from back side of front bezel. Remove the front bezel. 2. Attach the PB-3000E-DIO bracket, and fasten the 2 hex nuts to fix it as indicated. 3. Locate the connector(s) of PB-3000E-DIO module on top side of system. Spectra GmbH & Co. KG User Manual sales@spectra.de...
2. Locate the connector(s) of the PB-3000E-COM module on the top side of the system. Choose one connector to install the module. PowerBox 3000E series supports one PB-3000E-COM module installed on the system at most. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 138
2 screws to fix it. 4. Attach the PB-3000E-COM bracket, and fasten the 2 hex nuts to fix it as indicated. 5. Fasten the 8 D-Sub jack screws to fix the module. Spectra GmbH & Co. KG User Manual sales@spectra.de...
2. Locate the connector(s) of the PB-3000E-iCOM module on the top side of the system. Choose one connector to install the module. PowerBox 3000E series supports one PB-3000E-ICOM module installed on the system at most. 3. Penetrate the COM ports of the PB-3000E-iCOM module through the holes on the bracket. Insert the CMI module vertically into the female connector on system’s mainboard until it’s connected...
Page 140
4. Attach the PB-3000E-iCOM bracket, and fasten the 2 hex nuts to fix it as indicated. 5. Fasten the 8 D-Sub jack screws to fix the module. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
1. Penetrate the PB-3000E-LAN-M12 ports through the holes on the bracket. Insert the CMI module vertically into the female connector on system’s mainboard until it’s connected firmly and fasten 4 copper pillars to fix PB-3000E-LAN-M12 module. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 142
2 thermal pads onto the heatsink carefully. Before putting on the heatsink (in the next step), please make sure the protective films on the Thermal Pads have been removed! Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 143
Thermal Pad has been removed! Once the steps are finished, after system power on, PoE LED (on PB-3000E-LAN or PB-3000E- LAN-M12 module) will light blue as shown below. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Insert the connector of IGN module to the female connector on system motherboard. (Make sure all the pins of IGN module’s connector are firmly connected.) Fasten the two screws to secure the power ignition board. Spectra GmbH & Co. KG User Manual sales@spectra.de...
1. Loosen the 2 screws on the cover plate and then remove it. 2. Attach the MEC-COM brackets, and fasten the 4 screws to fix it as indicated. 3. Locate the Mini PCIe socket(s) on the bottom side of the system. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 146
45° 5. Press the card down and secure it with 2 screws. 6. Remove the 4 D-Sub jack screws from the COM ports. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 147
7. Connect the other end of the wire to the Mini PCIe card as indicated. 8. Attach the COM ports onto the back side of the cover plates, and then fasten the 4 D-Sub jack screws to secure the COM ports. Spectra GmbH & Co. KG User Manual sales@spectra.de...
1. Loosen the 2 screws on the cover plate and then remove it. 2. Attach the MEC-USB bracket, and fasten the 2 screws to fix it as indicated. 3. Locate the Mini PCIe socket(s) on the bottom side of the system. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 149
4. Tilt the Mini PCIe card at a 45-degree angle and insert it to the socket until the golden finger connector of the card seated firmly. 45° 5. Press the card down and secure it with 2 screws. 6. Connect the attached wire to the USB board. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 150
7. Connect the other end of the wire to the Mini PCIe card as indicated. 8. Attach the USB board onto the back side of the cover plate, and then fasten the two screws to secure the module. Spectra GmbH & Co. KG User Manual sales@spectra.de...
1. Loosen the 2 screws on the cover plate and then remove it. 2. Attach the MEC-LAN bracket, and fasten the 2 screws to fix it as indicated. 3. Locate the Mini PCIe socket(s) on the bottom side of the system. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 152
4. Tilt the Mini PCIe card at a 45-degree angle and insert it to the socket until the golden finger connector of the card seated firmly. 45° 5. Press the card down and secure it with 2 screws. 6. Connect the attached wires to the LAN board. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 153
7. Connect the wires to the Mini PCIe card as indicated. 8. Attach the LAN board onto the back side of the cover plate, and then fasten the two screws to secure the module. Spectra GmbH & Co. KG User Manual sales@spectra.de...
1. Prepare an external fan. Loosen the 2 screws halfway on mounting frame before attempting to install it. 2. Slide the FAN into the middle groove of chassis as illustrated. Tighten the 2 screws to fix it onto chassis. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Page 155
3. Move the fan to the center of chassis. Tighten the 2 screws marked on photo to secure it. 4. Connect the FAN cable to external fan power connector at rear panel. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Unscrew 6 screws to remove 3 I/O brackets from rear panel. Insert the fan connector to the power connector (power4). Attach the FAN from back side of rear panel, and then fasten the 4 screws to fix it. Spectra GmbH & Co. KG User Manual sales@spectra.de...
Page 157
User can use cable ties to tie the wire from the cut holes as indicated. Spectra GmbH & Co. KG User Manual sales@spectra.de Spectra PowerBox 3000E...
Need help?
Do you have a question about the PowerBox 3000E Series and is the answer not in the manual?
Questions and answers