Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Jet XACTA
Summary of Contents for Jet XACTA
- Page 1 Assembly Instructions and Parts Manual ® XACTA Commercial Fence & Rails (50” Rip) for JTAS-12-DX Table Saw 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708955Z Ph.: 800-274-6848 Revision B1 02/2019 www.jettools.com Copyright © 2014 JET...
-
Page 2: Warranty And Service
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever. -
Page 3: Table Of Contents
6.12 Cursor Adjustment ..........................10 7.0 Replacement Parts ............................11 7.1.1 XACTA Fence Rail Assembly – Exploded View ..................11 7.1.2 XACTA Fence Rail Assembly – Parts List ..................... 11 7.2.1 XACTA Fence Assembly – Exploded View ................... 12 ... -
Page 4: Safety Warnings
18. Provide for adequate space surrounding work Do not use the table saw for other than its area and non-glare, overhead lighting. intended use. If used for other purposes, JET 19. Keep the floor around the machine clean and disclaims any real or implied warranty and free of scrap material, oil and grease. -
Page 5: About This Manual
Your fence has been designed and constructed to provide consistent, long-term operation if used in accordance with the instructions as set forth in this document. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 6: Specifications
Paint finish ..............................powder coat The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 7: Setup And Assembly
#3 cross point screwdriver 7/16” wrench 1/2" wrench Combination square & straight edge 1/4” hex key 3/16” hex key 6.2 Shipping contents XACTA Fence II Front rail Back rail Guide tube Black plastic end covers Owner’s manual Warranty registration card... -
Page 8: Switch Installation
The front rail must be low enough to clear the miter gauge slot, and parallel to the table top: Place an adjustable square on the table as shown in Figure 3. 37. Check height of front rail at several locations along the surface of the saw table. -
Page 9: Xacta Fence
(A, B, Figure 9). Figure 9 Figure 6 If adjustment is necessary: 6.7 XACTA Fence 45. Unlock fence. Screw knob into threaded handle on fence, as 46. Raise or lower two nylon adjustment screws shown in Figure 7. -
Page 10: Clamping Pressure
59. Make a test cut and confirm the adjustment is 6.10 Clamping Pressure correct. The XACTA Fence has been adjusted by the Note: If the cursor does not have enough travel to manufacturer to lock securely when lock handle is give the correct measurement, loosen guide rail pushed down. -
Page 11: Replacement Parts
Index No Part No Description Size ....708956Z ....XACTA Rail Assembly 50” (index # 1-13)............1 1 ....XF12DX-201 ..... Front Rail ....................... 1 2 ....TS-081F081 ....Flat Head Screw ............1/4”-20 × 1-1/2” ..... 7 3 .... -
Page 12: Xacta Fence Assembly - Exploded View
Index No Part No Description Size ....708955Z ....XACTA Commercial Fence 40” (index # 1-29) ..........1 1 ....XF12DX-101N ... Left Side Plate ....................1 2 ....XF12DX-102 ..... Fence Body Assembly ................... 1 3 ....XF2-103 ....Tube Cover ....................1 4 ....
Need help?
Do you have a question about the XACTA and is the answer not in the manual?
Questions and answers