Setting Up Your Digital Picture Frame; Remote Control; Using Your Digital Picture Frame - Dynex DX-DPF9 User Manual

Setting up your digital picture frame

# Item
6
DOWN /ROTATE
button
7
PREV button
8
NEXT button

Remote control

1
2
3
Digital Picture Frame
# Button
1 MENU
2
PREV
3 COPY/DEL.
4 EXIT
5 ZOOM
6
UP
7 PLAY/PAUSE/MODE Press to confirm a selection,
8
NEXT
9
DOWN /ROTATE
10 SLIDE SHOW
Setting up the remote control
Note
: Pull the plastic tab sticking out of the remote control. It protects the
battery. The remote control cannot work unless it is removed.
To install or replace the remote control battery:
1 Hold the remote control with the control buttons facing
downward.
Description
Press to navigate the on-screen menus
or to rotate a photo.
Press to navigate the on-screen menus
or to view the previous photo.
Press to navigate the on-screen menus
or to view the next photo.
4
5
6
7
8
9
10
Action
Press to enter the Setup Menu.
Press to move the cursor to the
left or to access the previous
photo.
Press to copy a photo into frame
memory or to delete a photo
from the frame.
Press to return to the Main menu
or to enter the card selection
screen when the Main Menu is
displayed.
Press to enlarge the displayed
photo by 100%, 117%, 133%,
150%, or 200%.
Press to move the cursor up.
pause a slide show, or change
modes (Slide Show, Browse,
Thumbnail).
Press to go to the next photo.
Press to navigate the on-screen
menus or to rotate a photo.
Press to enter Slide Show mode.
2 While pressing down on the ridged area of the battery cover, pull
the tray out.
3 Remove the old battery, if necessary.
4 Place a CR2025 lithium battery on the tray with the positive + end
facing toward you.
5 Close the tray.
Setting up your digital picture
frame
To set up your digital picture frame:
1 Extend the stand from the back of your digital picture frame.
2 Rotate the stand to position your frame either vertically or
horizontally.
3 Place your digital picture frame on a flat surface.
4 Plug one end of the AC power adapter into your digital picture
frame.
5 Plug the other end of the AC power adapter into a wall outlet.
6 Insert a memory card or USB device into the appropriate slot.
Note
: The card only fits in one direction. Do not force it. The card should fit
snugly when correctly inserted.
7 Press the power button on the top of your digital picture
frame to turn it on.

Using your digital picture frame

To turn on your frame and select a photo:
1 Press on the top of your digital picture frame, the
POWER
frame turns on.
2 Insert a card into one of the card slots or insert a USB memory
device into the USB slot. The photos display automatically.
3 Press EXIT. The Main Menu opens.
4 Press EXIT again to enter the Card Selection screen, then press the
PREV r NEXT
o
5 Press PLAY/PAUSE/MODE
displays photos, based on the Transition Mode settings.
6 Press PLAY/PAUSE/MODE
Your frame displays a single picture.
7 Press PREV r NEXT
o
8 Press PLAY/PAUSE/MODE
mode. The thumbnail images appear on the screen in a table.
9 Press PREV NEXT
,
thumbnail, then press PLAY/PAUSE/MODE
picture.
To copy photos to your frame:
1 Press POWER on the top of your digital picture frame, the
frame turns on.
2 If your frame is in slide show mode, press EXIT. The Main Menu
opens. If the Main Menu is already open, go to the next step.
button to select the card you want.
to enter the Slide Show mode. This
again to enter the Browse mode.
to select a photo.
a third time to enter Thumbnail
UP or DOWN to select a
, ,
to show the
3