All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by BB 0567 TV Service...
EN 2 LC4.8A AA Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Index of this chapter: Dimensions (WxHxD cm) : 110.5 x 61 x 9.7 (37”) : 124 x 68 x 10.4 (42”) 1.1 Technical Specifications 1.2 Connection Overview...
Page 3
Technical Specifications, Connections, and Chassis Overview LC4.8A AA EN 3 Rd - Video Pr 0.7 V / 75 ohm 11 - n.c. 12 - DDC_SDA DDC data 13 - H-sync 0 - 5 V Cinch: CVI-1 Audio - In 14 - V-sync...
Page 4
EN 4 LC4.8A AA Technical Specifications, Connections, and Chassis Overview Chassis Overview LCD PANEL AUDIO STANDBY PANEL POWER SUPPLY SMALL PANEL SIGNAL BOARD SIDE CONTROL BOARD SIDE I/O PANEL LED PANEL F_15420_028.eps 100605 Figure 1-5 Chassis overview...
Safety Instructions, Warnings, and Notes LC4.8A AA EN 5 2. Safety Instructions, Warnings, and Notes Index of this chapter: Notes 2.1 Safety Instructions 2.2 Warnings 2.3.1 General 2.3 Notes • Measure the voltages and waveforms with regard to the Safety Instructions chassis (= tuner) ground (H), or hot ground (I), depending on the tested area of circuitry.
Page 6
For the repair of such sets nothing changes. Philips CE is producing lead-free sets (PBF) from 1.1.2005 onwards. In case of doubt whether the board is lead-free or not (or with...
Directions for Use LC4.8A AA EN 7 3. Directions for Use You can download this information from the following websites: http://www.philips.com/support http://www.p4c.philips.com...
EN 8 LC4.8A AA Mechanical Instructions 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing • Figures below can deviate slightly from the actual situation, 4.2 Service Positions due to the different set executions. 4.3 Assy/Panel Removal •...
Page 9
Mechanical Instructions LC4.8A AA EN 9 The aluminium stands (order code 3122 785 90480) can be 4.3.2 Side I/O Panel mounted with the back cover removed or still left on. So, the stand can be used to store products or to do measurements. It...
Page 10
EN 10 LC4.8A AA Mechanical Instructions 4.3.3 LED Panel 4.3.5 SSB Board Cover Shield F_15420_036.eps 070605 Figure 4-6 LED panel 1. Remove the fixation screws (1) and take the panel out of its brackets. F_15420_038.eps 2. Disconnect the cable (2) from the panel.
Page 11
Mechanical Instructions LC4.8A AA EN 11 4.3.7 Power Supply Panel 4.3.8 Class D Audio Amplifier/STBY Power Supply Panel F_15420_042.eps 070605 Figure 4-12 Class D audio amplifier/STBY power supply panel 1. Disconnect all cables (1) from the panel. 2. Remove the fixation screws (2) from the panel.
Page 13
Mechanical Instructions LC4.8A AA EN 13 To remove the LCD-panel, carry out the following steps: Set Re-assembly 1. Disconnect the cables (1) from the “L” and the “R” loudspeakers and remove the cables from their cable To re-assemble the whole set, execute all processes in reverse clamps (1, see Figure “L”...
EN 14 LC4.8A AA Service Modes, Error Codes, and Fault Finding 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: How to Enter 5.1 Test Points To enter SDM, use one of the following methods: 5.2 Service Modes •...
Page 15
Service Modes, Error Codes, and Fault Finding LC4.8A AA EN 15 How to Navigate Menu Explanation Use one of the following methods: 1. LLLLL. This represents the run timer. The run timer counts • When you press the MENU button on the remote control, normal operation hours, but does not count standby hours.
Page 16
EN 16 LC4.8A AA Service Modes, Error Codes, and Fault Finding How to Store SAM Settings 8. Displays the detected Audio (e.g. stereo/mono). To store the settings changed in SAM mode, leave the top level 9. Displays the picture setting information.
Page 17
UART SERVICE CONNECTOR CONNECTOR Service Tools 5.4.1 ComPair Introduction ComPair (Computer Aided Repair) is a service tool for Philips I 2 C Power Consumer Electronics products. ComPair is a further 9V DC development on the European DST (service remote control), E_06532_021.eps 180804 which allows faster and more accurate diagnostics.
Page 18
EN 18 LC4.8A AA Service Modes, Error Codes, and Fault Finding • Starter kit ComPair32/SearchMan32 software and 5.5.1 How to Read the Error Buffer ComPair interface (excl. transformer): 3122 785 90450. • ComPair interface (excl. transformer): 4822 727 21631. You can read the error buffer in 3 ways: •...
Page 19
Service Modes, Error Codes, and Fault Finding LC4.8A AA EN 19 5.5.3 Error Codes The Blinking LED Procedure In case of non-intermittent faults, write down the errors present Using this procedure, you can make the contents of the error in the error buffer and clear the error buffer before you begin buffer visible via the front LED.
Page 20
EN 20 LC4.8A AA Service Modes, Error Codes, and Fault Finding Table 5-3 NVM Default values (option bit settings through NVM Editor in SAM Mode) Byte Nr. Bit Feature/Mode Description Byte 0 0 QSS (LSB) Mode of quasi split sound amplifier...
Page 21
Service Modes, Error Codes, and Fault Finding LC4.8A AA EN 21 Byte Nr. Bit Feature/Mode Description Byte 4 0 Signal Strength Signal Strength Switch in MK2 178(dec) 1 LPG 2 DVD TRAY LOCK Lock/Unlock DVD tray 3 SCRSAVER MODE Screen saver mode...
Page 22
EN 22 LC4.8A AA Service Modes, Error Codes, and Fault Finding 5.7.3 Tuner and IF 5.7.5 Power Supply No Picture in RF Mode, but there is a Noise Raster In case the power supply does not work, check (apart from the 1.
Alignments LC4.8A AA EN 87 8. Alignments Index of this chapter: 8.1 General Alignment Conditions 8.2 Hardware Alignments 8.3 Software Alignments Note: Figures below can deviate slightly from the actual situation, due to the different set executions. General: The Service Default Mode (SDM) and Service Alignment Mode (SAM) are described in chapter 5.
Page 88
EN 88 LC4.8A AA Alignments 8.3.1 SAM Menu 00035 LC4XAP1 1.15/S4XPVX 1.23 ERR 0 0 0 0 0 OP 000 057 140 032 120 128 000 . OP1 . Delta Cool Red . OP2 . Delta Cool Green -1 . OP3 .
Page 89
Alignments LC4.8A AA EN 89 8.3.4 ADC Gain and Grey Scale Alignment & Panel Size Settings Caution: • Do not change the NVM settings without understanding the function of each setting, because The table below shows a number of NVM settings used for incorrect NVM settings may seriously hamper the each model of TV set.
Page 90
EN 90 LC4.8A AA Alignments 8.3.5 Sound the NVM editor. For further settings, see also the table “ADC Gain and Grey scale alignment” elsewhere in this manual. • For NICAM sets: see paragraph 8.3.3. • For other sets: No adjustments needed for sound.
Page 91
Alignments LC4.8A AA EN 91 Table 8-3 Option codes in detail, at bit level Option byte & bit table for restoring the TV set to its original Factory Default settings via the NVM Editor in the SAM menu Description of feature/option to be switched ON or OFF...
EN 92 LC4.8A AA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets Index of this chapter: “Block diagram”) shows the Pixel Plus architecture; the 9.1 Introduction architectures of the other models (that are not discussed in this 9.2 Block Diagram...
Page 93
Table 9-1 Models and picture quality Tuner and IF Model Picture quality A Philips UV1316E/1318SD/TEDE9 Tuner is used in the TV board. The SIF signals are decoded by the Hercules. Tuning 37PF7320/69 /79 / 93 /98 Pixel Plus is done via I...
Page 94
EN 94 LC4.8A AA Circuit Descriptions, Abbreviation List, and IC Data Sheets Video: TV Part (Diagrams B1, B2, and B3) Figure 9-3 Block diagram video processing...
Page 95
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.8A AA EN 95 The video processing is completely handled by the Hercules Comb filter. Such a signal must be bypassed. Notch mode • IF demodulator. is not even an option since e.g. in double window, one part •...
Page 96
EN 96 LC4.8A AA Circuit Descriptions, Abbreviation List, and IC Data Sheets about a “Field Comb Filter”. Field Comb filters are only for PAL The offset block receives the motion dependant 2D/3D Comb of commercial interest. filtered signal as input. The black level of the luminance signal Field Comb filters show also problems on vertical colour is restored and the result is output.
Page 97
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.8A AA EN 97 9.6.3 Noise Reduction and Noise Estimator Video: Scaler Part (Diagram B7, B8 and B9) The noise reduction function is a sophisticated successor of the The Genesis gm1501 Scaler is a dual channel graphics and...
Page 98
EN 98 LC4.8A AA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.7.1 Teletext Path Audio Processing In Pixel Plus and Digital Crystal Clear models, which have an Hercules ADC (B18) and Columbus 3D combfilter (B19), the digital input of the scaler is used for the digital video signal (Columbus...
Page 99
106 P0.0/ I2SDI/O Lip Sync I2SDI/O Monitor Controller. 107 P1.3/ T1 PC-TV_LED P1.3 • On-chip 80C51 micro-controller from Philips Semiconductor UOCIII (Hercules) series. 108 P1.6/ SCL Each micro-controller has it own I C bus which hosts its own 109 P1.7/ SDA internal devices.
EN 100 LC4.8A AA Circuit Descriptions, Abbreviation List, and IC Data Sheets • LED. This signal is used as an indication for the Standby, 9.10 Abbreviation List Remote and Error Indicator. Region diversity: – During protection mode, the LED blinks and the set is...
Page 101
(Y/C) are reproduced LATAM LATin AMerica RGBHV Red, Green, Blue, Horizontal sync, LC04 Philips chassis name for LCD TV 2004 and Vertical sync project Read Only Memory Liquid Crystal Display Service Alignment Mode Light Emitting Diode; A semiconductor...
Page 102
Sound right SCART1 out SNDR-SC2-IN Sound right SCART2 out SNDR-SC2-OUT Sound right SCART2 out SOPS Self Oscillating Power Supply S/PDIF Sony Philips Digital InterFace; This is a consumer interface used to transfer digital audio SRAM Static RAM STBY STandBY SVHS...
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.8A AA EN 103 9.11 IC Data Sheets This section shows the internal block diagrams and pin layouts of ICs that are drawn as "black boxes" in the electrical diagrams (with the exception of "memory" and "logic" ICs).
Page 104
EN 104 LC4.8A AA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.11.2 Diagram B19, Type T6TU5XB (IC7M00, Columbus) Figure 1 Package outline (top view) WEB/ UVA0 UVA2 UVA4 UVA6 UVA8 SEL656 TST1 HREF DAVB /Di0 /Di2 /Di4 /Di6 /Di8...
Page 105
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.8A AA EN 105 9.11.3 Diagram B7+B8+B9, Type GM1501 (IC7401, Genesis) Block Diagram Parallel 2-wire IF/external Serial I/F JTAG GPIO micro Infra-red Rx Pulse Width Interface X186 External ndwid Modulator Micro- ROM I/F...
Page 106
EN 106 LC4.8A AA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.11.4 Diagram B12, Type S9993CT (IC7D03, HDMI Panellink), Reserved Block Diagram RESET# CSDA Registers Slave CSCL DSDA ---------------- Configuration Slave DSCL Logic Block Aux Data Logic HDCP HDCP...