Table of Contents
Advertisement
Available languages
Available languages
OBJ_DOKU-55444-001.fm Page 6 Tuesday, July 12, 2016 1:19 PM
6 | English
Product Features
The numbering of the product features refers to the illustra-
tion of the cordless worklight on the graphics page.
1 On/Off switch
2 Lock of the battery pack cover
3 Battery pack cover
4 Lamp head
5 Pedestal
6 Heat sink
7 Tripod mount 5/8"
8 Carrying handle
9 Screw for battery lid
10 Battery lid
11 Button cell (3 V lithium battery, CR 2032)
12 Battery pack*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Cordless Worklight
Article number
Rated voltage
Lighting duration, approx.
min/Ah
Permitted ambient
temperature
– during charging
– during operation* and
during storage
Recommended batteries
Recommended chargers
Degree of protection
Data transmission
®
Signal range
A) The signal range may vary greatly depending on external conditions,
including the receiving device used. The
icantly weaker inside closed rooms and through metallic barriers (e.g.
walls, shelving units, cases, etc.).
* Limited performance at temperatures <0 °C
** only for wireless charging batteries
*** applies only when battery pack cover is closed and locked
The colour rendition of illuminated objects can be distorted.
System Requirements
Mobile terminal device
Android 4.3 (and above)
(tablet, smartphone)
iOS 9 (and above)
1 609 92A 2SB | (12.7.16)
Assembly
Battery Charging (Accessory)
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the cordless worklight is switched off by means of a
protective circuit.
Do not continue to press the On/Off switch after the
To remove the battery 12, press the battery unlocking button
2 and pull the battery toward the rear out of the cordless
worklight. Do not exert any force when doing this.
Observe the notes for disposal.
GLI 18V-1900 C
Operation
3 601 D46 5..
V=
14.4
18
Initial Operation
40
50
Inserting the battery
Unlock the lock of the battery pack cover 2 and fold up the
battery pack cover 3.
°C
0...+45
Insert the charged battery 12 into lamp head 4 until it can be
felt to engage and faces flush against the lamp head 4.
°C
–20...+50
Close the battery pack cover 3 and then the lock of the battery
GBA 14,4
pack cover 2.
GBA 18 V ...
Make sure that the rubber lip is seated correctly when
GBA 18 V ...W
AL 18..
GAL 3680
GAL 18...W**
Changing the Button Cell(see figure B)
The cordless worklight is equipped with a CR2032 button cell
IP 64
so that it can be detected by the mobile terminal device even
(dustproof and
if no battery pack 12 is inserted.
splash-protected)***
To change the button cell, unlock the lock of the battery pack
cover 2 and fold up the battery pack cover 3. Unscrew the
® 4.1 (Low
screw of the battery lid 9 and take off the battery lid 10. Re-
Energy)
move the empty button cell and insert a new button cell.
A)
maximum 15 m
Make sure that the battery holder is not damaged when
removing the battery. Make sure that the plus pole of the
® range may be signif-
button cell faces upwards.
Remove the separating film between the button cell 11 and
the battery holder when using the tool for the first time.
Close the battery pack cover 3 and then the lock of the battery
pack cover 2.
Make sure that the rubber lip is seated correctly when
A warning will be displayed in the app before the button cell is
fully used up.
cordless worklight has been automatically switched
off. The battery can be damaged.
closing the battery pack cover. Otherwise protection
against dust and splash water will not be ensured.
closing the battery pack cover. Otherwise protection
against dust and splash water will not be ensured.
Bosch Power Tools
Advertisement
Table of Contents
