Maintenance And Service - Bosch GLI 18V-1900 C Professional Original Instructions Manual

OBJ_DOKU-55444-001.fm Page 7 Tuesday, July 12, 2016 1:19 PM
Standing Up
Carefully fold out the pedestal and place the cordless work-
light on the floor. Ensure that it has a firm footing.
Fastening to the tripod
You can use the tripod mount 7 to screw the cordless work-
light onto a tripod.
Tighten the 5/8" screw. Ensure that the tripod has a firm
footing.
Swivelling the Lamp Head (see figure A)
The lamp head is attached to the handle. The lamp head can
be set to five positions using the handle.
Switching On and Off
To start the cordless worklight, press the On/Off switch 1.
To switch off the cordless worklight, press the On/Off switch
1 again.
To save energy, only switch the cordless worklight on when
using it.
Adjusting the Brightness
Press the On/Off switch 1 briefly to switch on the cordless
worklight at maximum brightness. To adjust the brightness in
2 stages, hold down the On/Off switch 1 until the required
brightness is obtained.
Temperature Dependent Overload Protection
When exceeding the allowable heat-sink temperature of
60 °C, the cordless worklight switches off. Allow the cordless
worklight to cool down, then switch the cordless worklight on
again.
Control via App
The cordless worklight is equipped with a
which enables wireless data transfer to certain mobile termi-
nal devices which have a
phone, tablet).
In order to control the cordless worklight via
will need the "Bosch Toolbox" app. Download the app from
the corresponding app store (Apple App Store, Google Play
Store).
Then select the "Floodlight" subitem in the app. The display of
your mobile terminal device will show you all subsequent
steps required to connect the cordless worklight to the termi-
nal device.
The following information will be available when a connection
has been established with the mobile terminal device: remote
control, time control, combining multiple cordless worklights
in one group.
Working Advice
Shortly before the cordless worklight switches off because of
an empty battery, it will flash 3 times and shine with reduced
brightness.
Bosch Power Tools
Troubleshooting – Causes and Corrective Measures
Cause
A Bluetooth connection cannot be established with the
cordless worklight.
The cordless worklight is not
emitting a Bluetooth signal.
The cordless worklight cannot be switched on after
wireless charging.
The inductively chargeable
battery pack has to be re-ini-
tialised.

Maintenance and Service

Maintenance and Cleaning
The light source cannot be replaced. If the light source is de-
fective, the entire cordless worklight has to be replaced.
When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.
The cordless worklight is maintenance-free and contains no
components that must be replaced or maintained.
To avoid damage, clean the plastic lens of the cordless work-
light only with a dry, soft cloth. Do not use cleaning agents or
solvent.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
® module
www.bosch-pt.com
Bosch's application service team will gladly answer questions
® interface (e.g. smart-
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
®, you
include the 10-digit article number given on the nameplate of
the product.
People's Republic of China
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: 4008268484
Fax: (0571) 87774502
E-Mail: contact.ptcn@cn.bosch.com
www.bosch-pt.com.cn
HK and Macau Special Administrative Regions
Robert Bosch Hong Kong Co. Ltd.
21st Floor, 625 King's Road
North Point, Hong Kong
Customer Service Hotline: +852 2101 0235
Fax: +852 2590 9762
E-Mail: info@hk.bosch.com
www.bosch-pt.com.hk
English | 7
Corrective Measure
Remove the button cell 11
and battery pack 12 for 10
seconds.
Remove the battery pack 12
for 10 seconds.
1 609 92A 2SB | (12.7.16)