New Holland 6010 Service Manual page 23

Valve lift
Tiner - Internal Exhaust Gas Recirculation(EGR)
Intake opening (After BDC, during exhaust stroke)
Intake valve closing (Before TDC, during Exhaust stroke)
'Tiner' cam lobe lift
Intake valve lift (tiner)
Valve springs
Number per valve
Free length
Length loaded at 26.1 - 28.9 kg
Length loaded at 51.2 - 56.5 kg
Valve timing
Intake opening (before top dead centre)
Intake closing (after bottom dead centre)
Exhaust opening (before bottom dead centre)
Exhaust closing (after top dead centre)
Valve inserts
Valve guide OD
Valve guide oversize
Valve guide interference fit in housing cylinder head
Valve guide fitted ID after reaming
Valve stem clearance in guide
Maximum wear clearance .
Maximum valve stem eccentricity over one revolution with stylus on
sealing face
Crank gear
Crankshaft- Bearings
Main journal diameter
Main journal undersize
Main bearing wall thickness
Main bearing undersize
Main journal clearance in bearings
maximum wear clearance
Crank pin diameter
Crank pin undersize
Big end bearing wall thickness
Big end bearing undersize
Crank pin clearance in big end bearing
maximum wear clearance
Crankshaft thrust washer thickness
Thrust washer oversize
Width of main bearing housing over thrust washers
Length of corresponding main journal
Crankshaft end float
maximum wear end float
Maximum main journal and crank pin ovality or taper after grinding
Maximum main journal and crankpin ovality or taper due to wear or
taper due to wear
Maximum main journal misalignment
Crankshaft resting on end journals
Maximum misalignment of crank pins relative to main journals(in
either direction)
Tolerance from outer crankpin edge to crank‐shaft center line
Engine - Engine and crankcase
47969433 28/11/2016
10.1 [10.001] / 4
10.445 mm
3 °
61 °
1.076 mm
1.908 mm
1 mm
44.6 mm
34 mm
23.8 mm
15 °
45 °
56 °
26 °
13.933 - 14.016 mm
0.2 mm
0.005 - 0.050 mm
8.023 - 8.043 mm
0.023 - 0.058 mm (for intake valve)
0.033 - 0.068 mm (for exhaust valve)
0.13 mm
0.03 mm
79.791 - 79.810 mm
0.254‐ ‐ ‐ 0.508‐ ‐ ‐ 0.762‐ ‐ ‐ 1.016 mm
2.168 - 2.178 mm
0.254‐ ‐ ‐ 0.508‐ ‐ ‐ 0.762‐ ‐ ‐ 1.016 mm
0.034 - 0.103 mm
0.180 mm
63.725 - 63.744 mm
0.254‐ ‐ ‐ 0.508‐ ‐ ‐ 0.762‐ ‐ ‐ 1.016 mm
1.805 - 1.815 mm
0.254‐ ‐ ‐ 0.508‐ ‐ ‐ 0.762‐ ‐ ‐ 1.016 mm
0.033 - 0.087 mm
0.180 mm
3.378 - 3.429 mm
0.127‐ ‐ ‐ 0.254‐ ‐ ‐ 0.508 mm
31.766 - 31.918 mm
32.000 - 32.100 mm
0.082 - 0.334 mm
0.40 mm
0.01 mm
0.05 mm
0.10 mm
0.25 mm
±0.10 mm