Subscribe to Our Youtube Channel
Related Manuals for Pulsar Blue Power PSBS 5012E
Summary of Contents for Pulsar Blue Power PSBS 5012E
- Page 1 PSBS 5012E v.1.1 PSBS 13,8V/5A/65Ah/OC Buffer switch mode power supply unit with technical outputs. EN** Edition: 7 from 03.11.2016 Supercedes edition: 6 from 01.06.2016...
-
Page 2: Table Of Contents
BLUE POWER www.pulsar.pl PSBS5012E PSU features: uninterruptible power supply DC 13,8V/5A PSU technical output indicating PSU failure – OC type battery housing: 65Ah/12V LoB technical output indicating low battery voltage supply voltage AC 230V – OC type ... -
Page 3: Block Diagram
BLUE POWER www.pulsar.pl PSBS5012E OPTIONAL POWER SUPPLY CONFIGURATIONS: (visualization available at www.pulsar.pl) PSBS 5012E Battery 65Ah. 1. Buffer power supply PSBS 13,8V/relay module MPSBS/65Ah - PSBS 5012E + MPSBS + 65Ah 2. Buffer power supply PSBS 13,8V/4x1A/65Ah - PSBS 5012E + LB4 4x1A (AWZ575 or AWZ576) + 65Ah 3. - Page 4 BLUE POWER www.pulsar.pl PSBS5012E 1.3 Description of components and power supply terminals (Table 1, Fig.2). Table 1. Components of the Power supply PCB (Printed Circuit Board) (see Fig. 2). Component Description Jumper – configuration of discharged battery disconnection system (UVP) ...
-
Page 5: Technical Parameters
BLUE POWER www.pulsar.pl PSBS5012E Table 2. Components of the PSU (See Fig. 3). Component no. Description Isolation transformer Printed Circuit Board (see Table 1, Fig. 2) TAMPER; micro switch of tamper protection (NC) fuse in the power supply circuit 230V, T3,15A / 250V... - Page 6 BLUE POWER www.pulsar.pl PSBS5012E replacement) Automatic return 110-150% of the PSU power, manual restart (failure Overload protection OLP requires the disconnection of the DC output) Battery circuit protection SCP and reverse T6,3A- current limitation, the F melting fuse (failure polarity connection...
-
Page 7: Installation
BLUE POWER www.pulsar.pl PSBS5012E Table 6. Operation parameters . Environmental class Operating temperature -10ºC...+40ºC Storing temperature -20ºC...+60ºC Relative humidity 20%...90%, no condensation Vibrations during operation unacceptable Surges during operation unacceptable Direct insolation unacceptable Vibrations and surges during transport According to the PN-83/T-42106 standard 2. -
Page 8: Power Supply Operation Indication
BLUE POWER www.pulsar.pl PSBS5012E The shock protection circuit shall be done with a particular care: the yellow and green wire coat of the power cable should be connected to the terminal marked with the PE symbol. Operation of the PSU without the properly made and fully operational... -
Page 9: Technical Outputs
BLUE POWER www.pulsar.pl PSBS5012E 3.2 Technical outputs. The PSU has three indication outputs: EPS - technical output indicating 230V AC power failure. The output indicates 230V AC power failure. Under normal status – with the 230V AC supply on, the output is shorted to ground GND. -
Page 10: Service And Operation
BLUE POWER www.pulsar.pl PSBS5012E 4. Service and operation. 4.1 Overload or short-circuit of the power supply output (SCP activation). The AUX output of the PSU is protected against short-circuit by PTC polymer fuse. If the power supply load current exceeds Imax. (110% ÷ 150% @ 25°C of the PSU power), automatic disconnection of the output voltage, indicated by switching off the green LED, takes place. - Page 11 CAUTION! The power supply unit is adapted for cooperation with the sealed lead-acid batteries (SLA). After the operation period they must not be thrown but recycled according to the applicable law. Pulsar Siedlec 150, 32-744 Łapczyca, Poland Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50 E-mail: biuro@pulsar.pl, sales@pulsar.pl http:// www.pulsar.pl, www.zasilacze.pl...
Need help?
Do you have a question about the Blue Power PSBS 5012E and is the answer not in the manual?
Questions and answers