Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CDA 4Q4
Summary of Contents for CDA 4Q4
- Page 1 Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu...
- Page 2 Dear Customer Thank you for choosing one of our appliances, carefully designed and built by our specialist staff and thoroughly tested to satisfy your cooking requirements. We suggest that you read this Instruction Booklet so that you will understand fully how to operate your appliance. Please keep the booklet handy.
-
Page 3: Table Of Contents
Correct use of triple-ring burner ........ -
Page 4: Before Using For The First Time
BEFORE USING FOR THE FIRST TIME • Read the instructions carefully before installing and using the appliance • After unpacking the appliance, make sure it is not damaged. In case of doubt, do not use the appliance and contact your supplier or a qualified engineer. •... -
Page 5: Important Safeguards & Recommendations
IMPORTANT SAFEGUARDS & RECOMMENDATIONS • Do not carry out any cleaning or maintenance without first disconnecting the appli- ance from the electrical supply. • During and after use of the hob, certain parts will become very hot. Do not touch hot parts. -
Page 6: Features
Features Model: HVG 65 Model: 4Q Figure 1 Figure 2 Model: HVG 75 Figure 3... -
Page 7: Control Panel
CONTROL PANEL 5. Auxiliary burner control knob (1) 6. Rapid burner control knob (3) 7. Rear semirapid burner control knob (2) 8. Front semirapid burner control knob (2) 9. Rapid burner control knob (3) 10. Left semirapid burner control knob (2) 11. -
Page 8: Use Of The Hob
GAS BURNERS Gas flow to the burners is adjusted by turning the knob illustrated in fig. 5 which con- trols the safety valves. Turning the knob so that the indicator line points to the symbols printed on the panel achieves the following functions: ●... -
Page 9: Lighting The Burners
To re-light the burner, return the knob to the closed ● position, wait for at least 1 minute and then repeat the lighting procedure. If your local gas supply makes it difficult to light the burner with the knob set to maxi- mum, set the knob to minimum and repeat the operation. -
Page 10: Choice Of Burner
CHOICE OF BURNER The burner must be choosen according to the diameter of the pans and energy required. BURNER Auxiliary Semirapid Rapid Triple-ring Woks do not use pans with concave or convex bases (1) Front right Semirapid burner of models HVG 65, 4Q only. -
Page 11: Correct Use Of Triple-Ring Burner
The flat-bottomed pans are to be placed directly onto the pan-support. ✓ To use the WOK you need to place the proper stand (available as an accessory at extra cost) in order to avoid any faulty operation of the triple-ring burner (Figs. 8a - 8b). IMPORTANT: The special grille for wok pans (available as an accessory at extra cost) (fig. -
Page 12: Correct Use Of The Burners
Figure 9... -
Page 13: Cleaning And Maintenance
Cleaning and Maintenance GENERAL TIPS ✓ Before cleaning the hob switch it off and wait for it to cool down. ✓ Clean with a cloth, hot water and soap or liquid detergent. ✓ Do not use products which are abrasive, corrosive or chlorine based. ✓... -
Page 14: Control Knobs
ENAMELLED PARTS ✓ All the enamelled parts must be washed only with a sponge with soapy water or other non-abrasive products. ✓ Dry preferably with a soft cloth. ✓ If acid substances such as lemon juice, tomato conserve, vinegar etc. are left on the enamel for a long time they will etch it, making it opaque. -
Page 15: Burners And Grids
Check that the electrode “S” (figs. 11 and 14) is always clean to ensure trouble-free sparking. ✓ Check that the probe “T” (figs. 11 and 14) next to each burner is always clean to ensure correct operation of the safety valves. ✓... -
Page 16: Correct Positioning Of The Burners
The pan supports shall be level and must not rotate. Models with triple-ring burner: be sure not to fit the triple-ring burner pan support on the auxiliary, semi- rapid or rapid burners. The triple-ring burner pan support IS ONLY to be used on the triple-ring burner. - Page 17 MODELS WITH TRIPLE RING BURNER - CORRECT POSITIONING OF THE TRIPLE RING BURNER The triple ring burner must be correctly positioned (see fig. 14); the burner ribs must be fitted in their housing as shown by the arrow. The burner correctly positioned must not rotate (fig.
-
Page 18: Tips For Installation
Tips installation... -
Page 19: Location
✓ The appliance may be installed in a kitchen, Kitchen/diner or a bed sitting room, but not in a room or space containing a bath or a shower. ✓ The appliance must not be installed in a bed-sitting room of less than 20 m ✓... -
Page 20: Technical Information For The Installer
TECHNICAL INFORMATION FOR THE INSTALLER In order to install the cooktop into the kitchen fixture, a hole with the dimensions shown in fig. 19 has to be made, bearing in mind the following: ✓ Within the unit, between the bottom of the cooktop and the upper surface of a shelf there must be a clearance of at least 30 mm. - Page 21 HVG 65 - 4Q : 54 mm from top of countertop : at least 60 mm between the back side of the cut-out and the back of the countertop. INSTALLING THE SEPARATOR BELOW THE BASE OF THE COOKTOP It is recommended that a 30 mm clear- ance be left between to base of the cooktop and the separator.
-
Page 22: Fastening The Cooktop
FASTENING THE COOKTOP Each cooktop is provided with an installation kit including brackets and screws for fas- tening the cooktop to benches from 30 to 40 mm thick.The kit includes two "F" type brackets (for the front of the cooktop), two "R" type brackets (for the rear of the cook- top) and four self-threading screws "S"... -
Page 23: Ventilation Requirements
Ventilation requirements ✓ The appliance should be installed into a room or space with an air supply in accor- dance with BS 5440-2: 2000. ✓ For rooms with a volume of less than 5 m area will be required. ✓ For rooms with a volume of between 5 m 50 cm free area will be required unless the room has a door which opens directly to... -
Page 24: Gas Supply Requirements
Gas supply requirements IMPORTANT NOTE This appliance is supplied for use on NATURAL GAS or LPG (check the gas regulation label attached on the appliance). ✓ Appliances supplied for use on NATURAL GAS: they are adjusted for this gas only and cannot be used on any other gas (LPG) without modification. -
Page 25: Gas Connection
Propane gas a supply pressure of 37 mbar is required. The installation must conform to the relevant British Standards. CDA are not legally able to provide any assistance in the installation of gas appliances except to Corgi registered installers. Any Corgi registered fitter requiring help must pro- vide name, address and registration number. - Page 26 GAS CONNECTOR The fitting (fig. 23) is made up of: ✓ 1 nut “A” ✓ 1 elbow fitting “C” ✓ gasket “F” CONNECTION TO THE GAS SUPPLY ✓ Be careful when flexible pipes are used that they do not come into contact with moving parts.
-
Page 27: Conversion To Natural Gas Or Lpg
Conversion to Natural Gas or LPG REPLACING THE BURNER INJECTORS If the NATURAL GAS/LPG conversion kit is not supplied with the appliance this kit can be purchased by contacting the After-Sales Service. Choose the injectors to be replaced according to the table on next page. - Page 28 Table for the choice of the Injectors Cat: 2H3+ BURNER Auxiliary (A) Semirapid (SR) Rapid (R) Triple ring (TR) G30/G31 NOMINAL REDUCED POWER POWER 28-30/37 mbar Ø injecteur [Hs - kW] [Hs - kW] [1/100 mm] 1,00 0,30 1,75 0,45...
-
Page 29: Minimum Burner Setting Adjustment
MINIMUM BURNER SETTING ADJUSTMENT Check whether the flame spreads to all burner ports when the burner is lit with the gas tap set to the minimum position. If some ports do not light, increase the minimum gas rate setting. Check whether the burner remains lit... -
Page 30: Electrical Connection
IMPORTANT: The appliance must be installed by a qualified technician accord- ing with the current local regulations and in compliance with the manufac- turer instructions. Incorrect installation may be dangerous and the manufacturer can not be held responsible. Warning! This appliance must be earthed A properly earthed three pin plug (fused at 3 amps, to BS 1362 ASTA approved) must be used. - Page 31 SECTION OF THE SUPPLY CABLE - TYPE “H05V2V2-F” resistant to temperatures of 90°C WARNING: If the power supply cable is damaged, it must be replaced only by an authorised service agent in order to avoid a hazard. 230 VAC 50/60 Hz 3 x 0,75 mm ✓...
-
Page 32: Appliance Servicing
Appliance servicing CDA provide a quality and effective after-sales service to cover all your servicing needs. Please attach your receipt to this page for safekeeping. Please help us to help you by having the following information available when booking a service-call: 1. -
Page 33: Guarantee
CDA and the labour will be charged at the commercial rate applicable at the time of repair. - Page 36 Cod. 1103126 - ß4 Gas on glass cooktops Group Ltd Harby Road Langar Nottingham NG13 9HY ● ● ● ● VAT No : 528 7168 19 Registered in England : 2621460 ●...