Table of Contents
Related Manuals for CDA he6050ss
Summary of Contents for CDA he6050ss
- Page 1 Manual for Installation, Use and Maintenance Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu...
-
Page 2: Table Of Contents
Contents: Important Important Notes Using Your Hob Efficient Use Of Your Hob Care And Maintenance Fitting The Hob How To Install The Hob Mains Electricity Connection... -
Page 3: Important
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. - Page 4 CE Declarations of Conformity: This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical safety (LVD) and Electromagnetic interference compatibility (EMC). Parts intended to come into contact with food conform to EEC/89/109. IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
-
Page 5: Important Notes
Important Notes P lease note: • • E lectric hobs become hot and remain hot during and immediately after use. Do not touch the hob until it has been allowed to cool. • Keep children away from the appliance when in use. • Never use the hob top for storage. -
Page 6: Using Your Hob
Using Your Hob Fig.1 Electric hotplates: Control panel: 1. 180mm (FL) 1.5kW 5. (BR) 180mm Rapid hotplate control 2. 145mm (BL) 1.0kW 6. (BL) 145mm hotplate control 3. 180mm (BR) 2.0kW Rapid 7. (FL) 180mm hotplate control 4. 145mm (FR) 1.5kW Rapid 8. - Page 7 The ‘OFF’ position is indicated by the symbol ‘O’. The indicator will light when the hotplate is in use. When you have finished cooking, check to ensure that the hotplates are off and the indicator is not lit. Before using your hob for the first time, switch the hotplates on for a FEW SECONDS to burn off any grease left over from the manufacturing process.
-
Page 8: Efficient Use Of Your Hob
Efficient Use Of Your Hob The hob is equipped with hotplates of different sizes, designed to accommodate most shapes and sizes of pan. For best results, only use pans with flat bottoms and choose an appropriate hotplate depending on the size of the pan. The most efficient use of the hob is shown below, where the pan and hotplate are correctly chosen. -
Page 9: Care And Maintenance
Care and Maintenance The hob has a stainless steel surface, you should use a non-abrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. Stainless steel can be effectively cleaned by simply using a dilute solution of water and washing up liquid and drying to a shine with a clean cloth. - Page 10 IF YOUR HOB IS NOT WORKING: 1. Check that the mains supply has not been switched off. 2. Check that the fuse or circuit breaker has not blown/tripped.
-
Page 11: Fitting The Hob
Fitting The Hob Unpacking the hob: • Take care not to lose or mishandle any parts. Fitting position of the hob: This appliance must be installed a minimum of 50mm from any back wall and a minimum of 150mm away from any adjacent vertical surfaces, e.g. -
Page 12: How To Install The Hob
Notes: • D o not position this appliance above a refrigeration unit. The heat generated may cause the unit to fail. • T his appliance is designed to be installed into cabinet units capable of withstanding temperatures of 65°C above ambient or greater (typically 80-90°C). - Page 13 >61.5mm 477mm >600mm 560cm 557mm 185mm 185mm >165mm >165mm Fig.3 Fig.4 Fig.5 Fig.6...
-
Page 14: Mains Electricity Connection
Mains Electricity Connection Warning! this appliance must be earthed We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.T. and local regulations. This appliance is intended to be connected to fixed wiring and is not suitable for connection to a 13A plug or 13A supply. -
Page 15: Technical Data
• W hen installing this product we recommend you seek the help of another individual. TECHNICAL DATA: The table opposite shows the rated output of each hotplate: Mains electrical voltage: 230 - 240Vac, 50Hz Total rated electrical input: 6.0kW Hotplate Size Nominal Rating (kW) 180mm 145mm... - Page 16 Please contact our Customer Care Department for Service on the details below Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu...