Advertisement

Quick Links

Product P/N: 418771XGX
Surface Mounting
Hole
Hinge
NETWORK STATUS
POTS 1
POTS 2
TELEPHONE TROUBLESHOOTING
1. Identify the bad line.
2. Disconnect the plug from the appropriate POTS jack and plug
any working telephone into that jack.
If the telephone works, there is a problem inside the house.
If the telephone does not work, contact your service provider.
3. Remove the telephone and replace the plug into the POTS jack.
Security
4. Close the unit.
Screw
Hinge
Fiber Optic
Cable
Surface
Mounting
Hole
Ground
RF Drop
Power
Fiber Drop
Ground Drop
D
ESCRIPTION
®
The Total Access
 361 and 362 Single Family Unit (SFU) Optical Network 
Terminations (ONTs) are Gigabit Passive Optical Network (GPON) ONTs 
with RF Overlay. The Total Access 361 SFU ONT has 2 POTS, and 1 
Gigabit Ethernet interface. The Total Access 362 has 2 POTS, and 2 Gigabit 
Ethernet interfaces. The figure above illustrates the SFU ONT inner 
enclosure. GPON technology provides a consistent and common 
approach to advancing the public communications network using:
Traditional telephone service is Plain Old Telephone Service (POTS)
High speed data services
Video services 
The GPON network consists of an Optical Line Terminal (OLT) located at 
the central office and Optical Network Terminals (ONTs) located at the 
customer's premises. Between them lies the Optical Distribution Network 
(ODN) consisting of fibers and passive splitters or couplers.
In order to allow for the transmission of downstream and upstream traffic 
on one single fiber, different wavelengths are used for each direction. 
Downstream traffic uses 1490 nm, while upstream traffic is carried on 
1310 nm. For overlay RF TV distribution, a second downstream 
wavelength of 1550 nm is used.
Total Access 300 Series
GigE SFU GPON ONTs
with RF Overlay
Two-screw
Terminal
Bridges
TIP
RING
TIP
RING
POTS 1
TIP
RING
FXS 0/1
FXS 0/2
TIP
RING
POTS 2
TIP
RING
ETH 0/1
TIP
RING
ETH 0/2
ETH 1
ETH 2
ETH 0/1
ETH 0/2
TOTAL ACCESS 362 ONT
1187712G1
Ethernet
Connections
CLEI
TEL. NUMBER
12V , 1A
RF
Connection
Ethernet Drop
POTS Drop
Ground and Power
Drop Callout
This Job Aid covers the electronics modules (SFU ONT) and housings 
listed in the following table:
Total Access 361

Description

1187711G1
Total Access 361 SFU Electronics Module
4187711G12
Total Access 361 with Splice Housing
4187711G13
Total Access 361 with OptiTap Housing
Total Access 362
Description
1187712G1
Total Access 362 SFU Electronics Module
4187712G12
Total Access 362 with Splice Housing
4187712G13
Total Access 362 with OptiTap Housing
Total Access SFU
Description
Housings
1187770G1
Total Access ONT Splice Housing
1187771G1
Total Access ONT with OptiTap Housing
NOTE
The Total Access 361/362 SFU ONTs are only intended to be used with the
Corning Systems Model FNI‐NG series outdoor NID housing.
F
P
LED
RONT
ANEL
Label
Status
POWER
Off
Green
NETWORK
Off
STATUS
Green
Yellow
Red
POTS
Off
1 and 2
Green
2
Green Flashing
Yellow 
Red
ETH 1and 2
Off
Green
4
Yellow Flashing
I
NSTALLATION
NOTE
Refer to the Total Access 300 GigE SFU ONTs Installation Guide 
(P/N 6418771XGX‐5) for complete information on installing these units.
After unpacking the SFU ONT, inspect it for damage. If damage is noted, 
file a claim with the carrier and then contact ADTRAN. For more infor‐
mation, refer to the warranty.
Issue Date: March 2010
Document P/N: 6418771XGX-22B
S
Description
No power
Power is On
Administratively Shut Down
Normal
Test in progress
Fault Condition 
Administratively Shut Down
Off Hook
Ringing
Test mode
Fault
Link is down: no activity or 
Administratively Shut Down
10/100/1000 Link is up
TX or RX activity
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 418771 G Series and is the answer not in the manual?

Questions and answers

Summary of Contents for ADTRAN 418771 G Series

  • Page 1 Off Hook Ethernet interfaces. The figure above illustrates the SFU ONT inner  Green Flashing Ringing enclosure. GPON technology provides a consistent and common  Yellow  Test mode approach to advancing the public communications network using: Fault ♦ Traditional telephone service is Plain Old Telephone Service (POTS) ETH 1and 2 Link is down: no activity or  ♦ Administratively Shut Down High speed data services ♦ Green 10/100/1000 Link is up Video services  Yellow Flashing TX or RX activity The GPON network consists of an Optical Line Terminal (OLT) located at  the central office and Optical Network Terminals (ONTs) located at the  NSTALLATION customer’s premises. Between them lies the Optical Distribution Network  (ODN) consisting of fibers and passive splitters or couplers. NOTE In order to allow for the transmission of downstream and upstream traffic  on one single fiber, different wavelengths are used for each direction.  Refer to the Total Access 300 GigE SFU ONTs Installation Guide  Downstream traffic uses 1490 nm, while upstream traffic is carried on  (P/N 6418771XGX‐5) for complete information on installing these units. 1310 nm. For overlay RF TV distribution, a second downstream  wavelength of 1550 nm is used. After unpacking the SFU ONT, inspect it for damage. If damage is noted,  file a claim with the carrier and then contact ADTRAN. For more infor‐ mation, refer to the warranty.
  • Page 2 Required Tools and Supplies Multi Grounded Neutral (MGN) of the customer premises. Ensure  the wire is free of any sharp bends. Standard technician tools and those listed below are required for  5. Attach the ground wire to the side of the subscriber’s premises with  installing the SFU ONT: stainless steel half moon clamps or tie‐wrap the ground wire to the  ♦ Carpenter’s level riser conduit of the Buried Fiber Drop.  ♦ 3/32” screw driver for connecting SFU ONT power 6. Clean the MGN connector with emery cloth to insure a stable  ♦ connection. 5/32” hex tamper proof bit ♦ 7. Attach the ground wire from the SFU ONT to the MGN connector  RJ‐45/RJ‐11 crimper with the appropriate UL approved ground clamp/fitting. ♦ A telephony/data communication test set 8. Coat the connection with a metal corrosion preventative. ♦ PON power meter with wavelength filtering 9. Attach a Warning Ground Tag to this grounding connection. ♦ Fiberscope or videoscope ♦ Two #10 screws and appropriate surface anchors for mounting the  SFU ONT ♦ Assorted tie wraps for securing cabling and wiring ♦...
  • Page 3 Route OptiTap Fiber Drop Cable Pin 1 Refer to the illustration on the following page for fiber installations: Low Battery 1. Place the OptiTap fiber drop in the same rubber grommet channel  Battery Missing as the ground cable. The ground cable should be “below” the Opti‐ Pin 7 Replace Battery Tap fiber.  On Battery Signal Return 2. Connect the OptiTap fiber. 12V Return 3. Place the OptiTap connector in the cut‐out in the housing. +12VDC 4. Connect the fiber cable to the connector on the bottom of the  Power/Alarm UPS Power Electronics Module. Connector Connector 5. Route the cable so that when the Electronics Module is closed, the  (Note: Refer to the sticker on the bottom of the Power/Alarm Connector if needed) fiber is not pinched.
  • Page 4 From within the U.S. 1.800.726.8663 From outside the U.S. +1 256.963.8716 Warranty: ADTRAN will replace or repair this product within the warranty period if it does not PRICING AND AVAILABILITY 1.800.827.0807 meet its published specifications or fails while in service. Warranty information can...

Table of Contents