ADTRAN Total Access 300 Series Installation And Maintenance Manual

Note: Safety Cover has been
removed for illustration purposes.
Splice Tray
Fiber
Cable
Support
Clamp
Strength
Member
(Red)
Fiber In
Ground
Note:
When using the NID Housing,
ground the unit using the Ground
Lug attached to the Mounting Plate.
D
ESCRIPTION
The Total Access® 300 Series Small Business Unit (SBU) Active Ethernet
Optical Network Terminals (ONT) are Gigabit Passive Optical Network
ONTs. This Job Aid describes the Installation of the Total Access 372E
Active Ethernet Small Business Unit ONT (P/N 1287723G1).
The ONTs support the following:

Eight POTS ports

Four DS1 circuit emulated T1 interfaces (for PBX application)

Two Gigabit Ethernet interfaces

Active Ethernet interface
The figure above illustrates the ONT inner enclosure for the Total Access
372E.
NOTE
The Electronics Module Safety Cover and Fiber Tray Cover have been
removed to show additional details.
Optical technology provides a consistent and common approach to
advancing the public communications network using:

Plain Old Telephone Service (POTS)

High speed data and video services

PBX services
A E
CTIVE THERNET
Active Ethernet uses Ethernet components that are 802.3ah
compliant. Active Ethernet provides dedicated bandwidth based on
individual subscriber requirements that are applicable to both
Total Access 300 Series
Active Ethernet
Small Business Unit
Note: The RJ-11 POTS
ports are used for test
purposes only.
Tip (Green)
TOTAL ACCESS 372E
1287723G1
Ring (Red)
TELEPHONE TROUBLESHOOTING:
1. Identify the bad line (POTS 1-8).
2. Plug any working phone into
the appropriate jack.
If the telephone works, the unit
is functioning normally.
If the telephone does not work,
contact your service provider.
3. Remove the telephone from the
POTS jack.
Fiber Jumper
Cable (Yellow)
DS1
Connection (Red)
Ethernet
Connection (White)
Active Ethernet
Connecton
Note: Cable color is for
clarity purposes only.
Power
residential and business applications. Because Active Ethernet is pure
IP, no transition protocol is required.
The ONT and OLT employ bi-directional Small Form-factor
Pluggable (SFP) connectors for data transmission. To allow for trans-
mission of downstream and upstream traffic on a single fiber,
different wavelengths are used for each direction. Downstream traffic
uses 1490 nm, while Upstream traffic uses 1310 nm.
Using SFPs that are swappable depending on the application, using SFP-
based optics that are specific to the transmit and receive requirement (10
to 80 kilometers). Refer to the Total Access 300 Series Active Ethernet Small
Business Unit ONT Installation and Maintenance Guide
(P/N 612877SBAONT-5).
This Job Aid covers the electronics module and housings listed in the
following table:
Total Access 300 Description
1287723G1 Total Access 372E SBU Active Ethernet Electronics Module
1187774G1 Standard Business Unit Model 774 Housing
1187775G1 Standard Business Unit Model 775 OptiTap Housing
NOTE
The Total Access 372 SBU ONT is only intended to be used with the
Corning Systems Model FNI-NG series outdoor NID housing listed
above.
F P LED
RONT ANEL
Label Status
PWR Off

Green

NET Green

Yellow

Red

VOICE Off

1 – 8
Green

2 Green Flashing
DS1  Off
1 – 4
Green

Yellow

Alarm

ETHERNET Off

1 – 2
Green

4 Yellow Flashing
I
NSTALLATION
NOTE
Refer to the Total Access 300 Series SBU ONT Installation and Maintenance
Guide (P/N 612877SBGONT-5) for complete information on installing
these units both with, and without the NID Housing.
jobAid
Issue Date: July 2012
Document P/N: 612877SBAONT-22A
S
Description
No power
Power is On
OLT has activated the ONT
OLT is discovering and ranging the
ONT
The OLT has shut down ONT
Fiber is disconnected, or GPON
interface is down
At least one port is Off Hook
At least one port is Ringing
Fiber is disconnected, or GPON
interface is down
Link is up
Link in test mode
Fault
Link is down, no activity, or Admin-
istratively Shut Down
10/100/1000 Link is up
TX or RX activity
1