Page 1
All manuals and user guides at all-guides.com EX-CD3 CD/TUNER/AMPLIFIER NOTES PC boards shown are viewed from parts side. The parts with no reference number or parts number in the exploded views are not supplied. As regards the resistors and capacitors, refer to the circuit diagrams contained in this manual.
All manuals and user guides at all-guides.com CONTENTS SPECIFICATIONS................. . 2 IC PIN FUNCTION .
Page 3
All manuals and user guides at all-guides.com IC36 PIN FUNCTION (IC : BVITMP87PM78F)(AMP) PIN No. NAME DESCRIPTION POWER SUPPLY (+5V) 1, 25 BUS for CD CLOCK HREQ BUS for CD CHIP ENABLE SLQCLK RESET for CD SLQIN MUTE for CD SINGLE SLQOUT DATA EUROPE VERSION RDS DATA CONTROL PORT...
Page 4
All manuals and user guides at all-guides.com IC 66 PIN FUNCTION (IC : BVITMP87PM78F)(CD) PIN No. NAME DESCRIPTION POWER SUPPLY (+5V) 1, 25 BUS for CD DATA BUS 0 BUS for CD DATA BUS 1 BUS for CD DATA BUS 2 BUS for CD DATA BUS 3 BUS for CD CLOCK...
Page 5
All manuals and user guides at all-guides.com PIN ASSIGNMENTS (TOP VIEW) PIN BLOCK DIAGRAM SERVICE MANUAL...
Page 6
All manuals and user guides at all-guides.com IC11 (TUNER) LA1836M BLOCK DIAGRAM TDA7318D IC23(INPUT) LC4966 SERVICE MANUAL...
Page 7
All manuals and user guides at all-guides.com ALIGNMENT INSTRUCTIONS EQUIPMENT NEEDED: AM Signal Generator FM Signal Generator Oscilloscope VTVM(AC, DC) Test loop antenna (AW Adjustment) Dummy antenna (FM Adjustment) Stereo signal modulator Frequency counter Distortion analyser IMPORTANT 1. Check power-source voltage. 2.
All manuals and user guides at all-guides.com MEASUREMENTS AND ADJUSTMENTS 1. FM, AM TRACKING VOLTAGE ADJUSTMENTS (FM, AM) DC VOLTMETER ......CONNECT TO TEST POINT TP1 and GND Band Frequency Adjust for Adjustment 87.50MHz 1.5V 530KHz T404 2. AM RF ADJUSTMENT Signal Generator ......
Page 9
All manuals and user guides at all-guides.com 4. FM MONO DISTORTION ADJUSTMENT DC VOLT METER ......Connect to TP1(-), TP2(+) Through the choke coll (100 H) Signal Generator......Connect to FM ANT Jack (FM IN) through the dummy. Distortion Meter ......Connect to the output. Frequency Adjust for Adjustment...
All manuals and user guides at all-guides.com TA2092N (POWER DRIVER) PIN No. NAME DESCRIPTION Power GND Connected to substrate. PW GND pin are connected inside. Inverted output for CH1 OUT (-) 1 Supply terminal of output stage for CH1 Supply terminal of output stage are not connected to other channel terminal. Non-inverted output for CH1 OUT (+) 1 Input for CH1.
Page 11
All manuals and user guides at all-guides.com TA2109F (RF/DIGITAL SERVOR) PIN No. NAME DESCRIPTION REMARK Power supply input terminal Main beam I-V amp input terminal Connected to pin diode A,C Main beam I-V amp input terminal Connected to pin diode B,D Sub beam I-V amp input termianl Connected to pin diode F Sub beam I-V amp input termianl...
Page 12
All manuals and user guides at all-guides.com SERVICE MANUAL...
Page 13
All manuals and user guides at all-guides.com SERVICE MANUAL...
Page 14
All manuals and user guides at all-guides.com SERVICE MANUAL...
Page 15
All manuals and user guides at all-guides.com SERVICE MANUAL...
Page 16
All manuals and user guides at all-guides.com SERVICE MANUAL...
Page 17
All manuals and user guides at all-guides.com SERVICE MANUAL...
Page 18
All manuals and user guides at all-guides.com...
Page 19
All manuals and user guides at all-guides.com...