Before The First Use - Vitek VT-1761 Manual Instruction

ENGLISH
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY. ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.

BEFORE THE FIRST USE

After unit transportation or storage at low tem-
perature keep it for at least three hours at room
temperature before switching on.
There may be water spots in the air humidifier, this
is normal, as the unit has undergone factory qual-
ity control.
Unpack the unit, remove any stickers and pack-
–
age materials that can prevent unit operation.
Check the unit for damages. In case of damages
do not switch the unit on.
Remove the water tank (4) and remove a trans-
–
porting plastic part (pic. 1).
A protective transport gasket is installed under
–
the movable float (4) in the process chamber (9).
Lift the water tank (2) and remove the float (4)
–
soft transport gasket (fig. 1). Then install the
water tank (2) back on the unit body (7).
Before plugging the unit in make sure that your
–
home mains voltage corresponds to the unit
operating voltage.
Notes:
Use the humidifier at the room temperature
–
from +10° С to +40° С, and relative humidity less
than 80%.
Water temperature should not exceed +40°С.
–
Installing batteries in the remote control (RC)
•
Open the RC battery compartment lid and insert
a CR2025 battery, strictly following the polarity.
• Install the battery compartment lid back to its
place.
Note: The unit can be supplied with the battery
installed in the RC battery compartment. In this
case if there is an isolation insert in the RC battery
compartment, remove the insert.
Battery replacement
•
Open the battery compartment lid, replace the
old battery with a new one, strictly following the
polarity, then close the battery compartment lid.
OPERATING BUTTONS AND INDICATION
Notes:
the operation mode buttons on the control panel
–
(10) are touch-sensitive, touch the button to
switch the necessary operation mode on.
every pressing of the buttons is confirmed with
–
a sound signal.
On/off button (15) «
Touch the button (15) to switch the unit on and
touch the button again to switch the unit off.
Timer setting button (14) «
Set the timer operation time by consequently
–
touching the button (14), the corresponding
indicators (13) will light up on the control panel
(10) in the following order:
2Ч - 2 hours;
4Ч - 4 hours;
8Ч - 8 hours.
To switch the timer off consequently press the
–
button (14) until the indicators (13) on the con-
trol panel (10) go out.
Mist release intensity control button/«night»
mode on/off button (16) «
You can select the intensity of the mist release
–
by consequently touching the button (16), the
corresponding indicators (11) will light up on the
control panel (10) in the following order:
I - low intensity;
II - medium intensity;
III - high intensity.
Notes: the medium mist release intensity (II) will
be set automatically when the unit is switched on
for the first time.
Night mode
To turn the «night» mode on touch the «
–
ton (16) for 5 seconds, the indicators (11, 12, 13)
on the control panel (10) will go out.
To turn the «night» mode off touch the button
–
(16) for 5 seconds again.
Notes: the unit in the «night» mode will operate with
the set mist release intensity, and the indicators (11,
12, 13) and the sound signals will not disturb you
during sleep.
Remote control (RC)
The operation mode buttons on the RC duplicate
buttons on the control panel (10).
On/off button (17) «
Press the button (17) to turn the unit on, press the
button (17) again to turn the unit off.
Mist release intensity control button (18) «
Set the desired mist release intensity in accordance
with the recommendations above by consequently
pressing the button (18).
Timer setting button (19) «
Set the timer operation time in accordance with the
recommendations above by consequently pressing
the button (19).
4
»
»
»
» but-
»
»
»