Table of Contents
Advertisement
Remove the water tank, fill with fresh water up to the
2.
"MAX" mark and insert fully in the tank recess.
→ "Filling the water tank", Page 19
Press
until the required power level is reached.
3.
a The display shows the selected steam setting.
Use the rotary selector to set the required cooking
4.
time.
You can also adjust the cooking time first and then
the steam setting.
Press
to start.
5.
a The arrow for
goes out and the symbol without
the arrow lights up.
lights up,
a
a The temperature display lights up completely.
a The cooking time counts down on the display. The
amount of time a tankful of water will last varies de-
pending on the steam setting.
Notes
¡ When the time has elapsed, a signal sounds.
¡ If the water tank runs out of water while the appli-
ance is in operation, the appliance is paused and
the arrow of the water tank symbol flashes. Fill
the water tank with fresh water up to the "MAX"
mark and press
¡ You can use
to change the steam setting at any
time when the appliance is in operation.
¡ After cooking with steam, wipe out the drip trough
and the cooking compartment.
→ "After using steam operation", Page 20
11.3 Steam combined operation
With some types of heating, you can switch on the
steam function. When you cook with added steam, the
appliance introduces steam into the cooking compart-
ment at various intervals and with varying degrees of
intensity. This gives you a better cooking result.
Your food
¡ becomes crispy on the outside.
¡ develops a glossy surface.
¡ is succulent and tender on the inside.
¡ only undergoes a minimal reduction in volume.
Steam combined operation can be used with the
following functions:
Microwave
¡
Full-surface grill
¡
Centre-area grill
¡
Setting the steam combined operation
Switch on microwave mode in addition to a type of
heating.
Set the function selector to a combinable type of
1.
heating.
a The display shows a default value for the temperat-
ure.
Use the rotary selector to set the required setting
2.
Press
until the required setting is selected on the
3.
display.
a The water tank symbol appears on the display.
Fill the water tank.
4.
Press
to start.
5.
a The cooking time counts down and the operation
starts.
a You can see the cooking time counting down.
to resume operation.
lights up.
a
a Once the cooking time has elapsed, the appliance
stops the operation and a signal sounds.
Notes
¡ If the water tank is empty, the appliance continues
to operate but without added steam. Nothing ap-
pears on the display.
¡ Opening the appliance door affects the cooking res-
ult. Always keep the appliance door closed when
cooking.
Changing the steam setting
Press
until the required setting appears on the
▶
display.
Note: Repeatedly pressing this switches through the
settings, from the highest to the lowest setting. After
the lowest setting, the steam function is deactivated.
Press again to activate the steam function, starting at
the highest setting.
11.4 Pausing the operation
Press
or open the appliance door.
1.
a The appliance stops the operation.
flashes.
a
Close the appliance door.
2.
Press
.
3.
a The appliance continues the operation.
lights up.
a
11.5 Stopping operation
You can stop operation at any time.
Turn the function selector to the off position.
▶
The fan may continue to run after operation has
been paused or stopped.
a The appliance stops any ongoing functions.
11.6 Filling the water tank
The water tank is located to the right behind the tank
cover, below the appliance door. Before starting an op-
eration with steam, open the tank cover and fill the wa-
ter tank with water.
WARNING ‒ Risk of fire!
Due to the hot surfaces, vapours from flammable li-
quids may catch fire in the cooking compartment (ex-
plosion). The appliance door may spring open. Hot
steam and jets of flame may escape.
Do not pour flammable liquids (e.g. alcoholic drinks)
▶
into the water tank.
Only fill the water tank with water or with the descal-
▶
ing solution we have recommended.
WARNING ‒ Risk of burns!
The water tank may heat up while the appliance is in
operation.
Wait until the water tank has cooled down from the
▶
previous operation.
Remove the water tank from the tank recess.
▶
Requirement: The water hardness must be set cor-
rectly.
→ "Setting the water hardness", Page 13
Steam en
19
Advertisement
Table of Contents
