Maintenance; Optional Accessories - Makita DTP131 Instruction Manual

Drilling capacity
Steel
High speed
Wood
Steel
Low speed
Wood
Screwdriver mode
CAUTION:
• Adjust the number on the LED display to the
proper torque level for your work.
• Make sure that the driver bit is inserted straight
in the screw head, or the screw and/or bit may
be damaged.
• Hold the tool firmly. When the clutch cuts in or
refastening, a sudden twisting force may occur
and it can twist your wrist.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually.
NOTE:
• This tool employs an electronic clutch. The tool
stops automatically when the clutch cuts in. To
keep operating, release the switch trigger once.
• When driving wood screws, predrill pilot holes
to make driving easier and to prevent splitting of
the workpiece. See the chart.
Nominal diameter of wood screw
(mm)
3.1
3.5
3.8
4.5
4.8
5.1
5.5
5.8
6.1
NOTE:
• See the following chart for the relation between
the number of torque setting and fastening
torque rate.
The fastening torque rate will be different
depends on materials. Make a test fastening to
get the desired torque before operation.
6.5 mm
12 mm
10 mm
21 mm
Recommended size of pilot hole
(mm)
2.0 - 2.2
2.2 - 2.5
2.5 - 2.8
2.9 - 3.2
3.1 - 3.4
3.3 - 3.6
3.7 - 3.9
4.0 - 4.2
4.2 - 4.4
Number
on LED
Display
Approx. 2.5 N m
1
(Approx. 25.5 kgf. cm)
Approx. 4.6 N m
3
(Approx. 46.9 kgf. cm)
Approx. 8.1 N m
5
(Approx. 82.6 kgf. cm)
Approx. 10.0 N m
7
(Approx. 102.0 kgf. cm)
Approx. 11.5 N m
9
(Approx. 117.3 kgf. cm)

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
the battery cartridge is removed before attempt-
ing to perform inspection or maintenance except
for the following troubleshooting related to the
light.
• Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks
may result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
• These accessories or attachments are recom-
mended for use with your Makita tool specified
in this manual. The use of any other accessories
or attachments might present a risk of injury to
persons. Only use accessory or attachment for
its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Screw bits
• Hook
• Plastic carrying case
• Makita genuine battery and charger
NOTE:
• Some items in the list may be included in the
tool package as standard accessories. They
may differ from country to country.
12 ENGLISH
Fastening torque rate
Low (1)
High (2)
.
Approx. 1.1 N m
(Approx. 11.2 kgf. cm)
.
Approx. 2.0 N m
(Approx. 20.4 kgf. cm)
.
Approx. 3.0 N m
(Approx. 30.6 kgf. cm)
.
Approx. 4.0 N m
(Approx. 40.8 kgf. cm)
.
Approx. 5.8 N m
(Approx. 59.1 kgf. cm)
.
.
.
.
.