Page 1
Keep this manual in a safe place for future reference FREE FLOAT STEAM TRAPS JH3S-B/JH5SL-B/JH5SH-B JH3S-B JH5SL-B JH5SH-B Manufacturer 881 Nagasuna, Noguchi, Kakogawa, Hyogo 675-8511, Japan Te l : [81]-(0)79-422-1122 Fax: [81]-(0)79-422-0112 Copyright (C) 2021 by TLV CO., LTD. All rights reserved.
1 MPa = 10.197 kg/cm , 1 bar = 0.1 MPa For products with special specifications or with options not included in this manual, contact TLV for instructions. The contents of this manual are subject to change without notice.
Be sure to use only the recommended components when repairing the product, and NEVER attempt to modify the product in any way. Failure to observe these precautions may result in damage to the product or burns or other injury due to malfunction or the discharge of fluids. Use only under conditions in which no freeze-up will occur.
Page 4
3. Configuration JH3S-B JH5SL-B JH5SH-B !5 !4 !5 !4 @4 @5 Screwed Socket Weld Description M R F Description M R F Description M R F Body Screen Cover Bolt Cover Snap Ring Cover Nut Float Air Vent Screen Connector...
5. Proper Installation • Installation, inspection, maintenance, repairs, disassembly, adjustment CAUTION and valve opening/closing should be carried out only by trained maintenance personnel. • Take measures to prevent people from coming into direct contact with product outlets. • Install for use under conditions in which no freeze-up will occur. •...
Screen(s) Check for deformation, damage, oil film or water inside Float Check for rust, scale, oil film, wear or damage Orifice Opening Tightening Torque and Distance across Flats JH3S-B JH5SL-B JH5SH-B Part & No. (lbf . ft) (lbf . ft) (lbf .
Page 8
Disassembly/Reassembly (to reassemble, follow procedures in reverse) JH5SL-B Part & No. JH3S-B During Disassembly During Reassembly JH5SH-B Coat threads with anti-seize and Drain Plug 25 Use a wrench to remove tighten to the proper torque Remove gasket and clean Replace with a new gasket, coat...
Page 9
8. Instructions for Plug / Holder Disassembly and Reassembly The seal on the threaded plugs/holders found on TLV products is formed by a flat metal gasket. There are various installation orientations for the gaskets, such as horizontal, diagonal and downward, and the gasket may be pinched in the thread recesses during assembly.
(When conducting a visual inspection, flash steam is sometimes mistaken for steam leakage. For this reason, the use of a steam trap diagnostic instrument such as TLV TrapMan is highly recommended.) Flash Steam...
Page 11
Subject to the limitations set forth below, TLV Corporation, a North Carolina corporation (“TLV”) warrants that products which are sold by it, TLV CO., LTD., a Japanese corporation (“TLVJ”) or TLV International, Inc., a Japanese corporation (“TII”), (hereinafter the “Products”) are designed and manufactured by TLVJ, conform to the specifications published by TLV for the corresponding part numbers (the “Specifications”) and are free from defective workmanship and materials.
Page 12
WARRANTY NOT NEGATED HEREBY, AND ANY IMPLIED WARRANTY NOT NEGATED HEREBY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, DO NOT COVER, AND NEITHER TLV, TII NOR TLVJ WILL IN ANY EVENT BE LIABLE FOR, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO LOST PROFITS, THE COST OF DISASSEMBLY AND SHIPMENT OF THE DEFECTIVE PRODUCT, INJURY TO OTHER PROPERTY, DAMAGE TO BUYER’S OR THE FIRST...
Need help?
Do you have a question about the JH3S-B and is the answer not in the manual?
Questions and answers