Related Manuals for Fujitsu QFP-100P
Summary of Contents for Fujitsu QFP-100P
- Page 1 FUJITSU SEMICONDUCTOR SS01-26010-1E SUPPORT SYSTEM MC-8FX Family QFP-100P (0.65 mm pitch) HEADER BOARD MB2146-251 OPERATION MANUAL...
- Page 2 MC-8FX family. Before using MB2146-251, be sure to read this manual. Consult the Sales representatives or the Support representatives of Fujitsu Limited for mass-pro- duced MCUs and evaluation MCUs which correspond on MB2146-251. *1 : The lead pitch of package (FPT-100P-M06) is 0.65 mm and the body size is 14 mm × 20 mm.
- Page 3 (i.e., submersible repeater and artificial satellite). Please note that FUJITSU will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products.
-
Page 4: Product Outline
: MB2146-301, MB2146-303) which mounted an evaluation MCU in the F MC-8FX family of Fujitsu 8-bit microcontrollers to a user system. To build an F MC-8FX evaluation environment, combine three products as shown in Figure 1: the header board, MCU board, and BGM adapter (Model number : MB2146-09). -
Page 5: Checking The Delivered Product
2. Checking the Delivered Product Before using the MB2146-251, confirm that the following components are included in the box: • QFP-100P (0.65 mm pitch) Header board * • Screws for securing Header board (M2 × 10 mm, 0.4 mm pitch) • NQPACK100RB179 * •... - Page 6 4. Notes on Designing ■ Notes on designing printed circuit board for the user system When the header board is connected to the user system, the parts mounted around the NQPACK in the user system may be touched the header board if the height of the parts is tall. To prevent this, design the printed circuit board for the user system such that the components do not exceed the height shown in Figure 2.
- Page 7 ■ MCU footprint design notes Figure 3 shows the recommended footprint dimensions of the NQPACK mounted on the printed cir- cuit board for the user system. Take the footprint in Figure 3 into consideration as well as the footprint of the mass production MCU when designing the printed circuit board for the user system.
- Page 8 5. Procedure for Connecting to the User System ■ Connecting Please mount the supplied NQPACK on the user system before using the LQFP-100P (0.5 mm pitch) header board. 1. To connect the header board to the user system, match pin 1 indicated by the index mark (▲) on the NQPACK mounted on the user system with pin1 indicated by the index mark (angle cut lin- early at one place only in slik screen) on the header board and then insert it (See Figure 4) .
- Page 9 MCU board Evaluation MCU board Screws for securing Header board Header board YQSOCKET Connection at the time of shipment YQPACK NQPACK User system Figure 5 Connecting MCU board/header board to user system ■ Disconnection 1. Remove the MCU board from the header board. Detach the four corners slowly in sequence not to excessively force the junction with the NQPACK.
- Page 10 6. Mounting Mass Production MCUs ■ Mounting To mount a mass production MCU on the user system, use the supplied HQPACK (IC socket cover) (See Figure 6) . 1. To mount a mass production MCU on the user system, match the index mark (▲) on the NQ- PACK mounted on the user system with the index mark (●) on the mass production MCU.
-
Page 11: Product Specification
7. Product specification ■ General specification Table 3 lists the general specifications of the header board. Table 3 General specification Item Description 5 °C to 35 °C (operation) , 0 °C to 40 °C (storage) Operating temperature and storage temperature Operating humidity and storage humidity 20 % to 80 % (operation) , 20 % to 80 % (storage) Approximately 40 mm ×... - Page 12 ■ MCU board I/F connector(CN1/CN2/CN3) CN1 and CN2 are MCU board I/F connectors. CN3 is the incorrect insertion prevention socket of a MCU board. The pin assignment of the MCU board I/F connector CN1 is shown in Table 5, and the pin assignment of the MCU board I/F connector CN2 is shown in Table 6.
- Page 13 Table 6 Pin assignment of the MCU board I/F connector CN2 Connector Evaluation Connector Evaluation Connector Evaluation Signal Signal Signal MCU Pin MCU Pin MCU Pin name name name Numbers Numbers Numbers Numbers Numbers Numbers SEL0 SEL3 SEL4 SEL1 P04C AVcc3 −...
- Page 14 ■ User system I/F YQPACK (U1) The pin assignment of user system I/F YQPACK in a header board is shown in Table 7. Table 7 Pin assignment of the User system I/F YQPACK in header board Connector Connector Connector Signal name Signal name Signal name Pin Numbers...
- Page 15 SS01-26010-1E FUJITSU SEMICONDUCTOR • SUPPORT SYSTEM MC-8FX Family QFP-100P (0.65 mm pitch) HEADER BOARD MB2146-251 OPERATION MANUAL February 2006 the first edition Published FUJITSU LIMITED Electronic Devices Edited Business Promotion Dept.