Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Marson MR16
Summary of Contents for Marson MR16
- Page 1 MR16 User’s Manual V1.1 MR16 Fixed UHF Reader User’s Manual...
-
Page 2: Table Of Contents
MR16 User’s Manual V1.1 Table of Content Chapter 1 Product Intro ..............3 1.1 Intro ................... 3 1.2 Interface ..................4 1.3 Accessory List ................6 1.4 Device installation..............7 1.5 GPIO Designation..............8 Chapter 2 UHF demo ................9 2.1 Operating Interface .............. -
Page 3: Chapter 1 Product Intro
MR16 User’s Manual V1.1 Chapter 1 Product Intro 1.1 Intro MR16 is a high-performance eight-channel fixed UHF reader which adopted Android 9.0 operating system. The core chip adopts Impinj R2000 module with 8 channels and it supports RS232, RJ45 and HDMI ports. -
Page 4: Interface
MR16 User’s Manual V1.1 1.2 Interface Pic.1-1... - Page 5 MR16 User’s Manual V1.1 12V 5000mA Power Supply HDMI GPIO (Support 2 path input photocoupler and 2 path output photocoupler with isolation.) UHF antenna port, SMA female*8 USB port, used to connect mouse and others, touch-screen function supported. Dial *#*#555666#*#* to enter engineer mode.
-
Page 6: Accessory List
MR16 User’s Manual V1.1 1.3 Accessory List Item Remark MR16 reader, 12V power adaptor & Power Cable Out of Box UHF antenna, 6dBi, 9dBi, 12dBi etc. (Optional) Sold Separately Feeder line, SMA male side connects with device, Not included. interface on other side needs match with antenna. -
Page 7: Device Installation
MR16 User’s Manual V1.1 1.4 Device installation MR16 reader adopts Android operating system, it can be connected with Internet through RJ45, WIFI and 4G etc. And connect with monitor through HDMI cable. Developer could use USB cable to connect device with PC for developing application, device could also be connected with PC through serial port cable. -
Page 8: Gpio Designation
MR16 User’s Manual V1.1 1.5 GPIO Designation IO1+ IO1- IO2+ IO2- IO3- IO3+ IO4- IO4+ Input Input Input Input port: Output Output Output Output port: port: port: optocoupl port: port: port: port: optocoup optocoup optocoup er 2 input optocoup optocoupl... -
Page 9: Chapter 2 Uhf Demo
MR16 User’s Manual V1.1 Chapter 2 UHF demo 2.1 Operating Interface Pic.4-1... - Page 10 MR16 User’s Manual V1.1 Connect monitor through HDMI cable and long-press power button for 3 seconds to switch on device. Click demo_uhf icon to enter demo as Pic.4-1, UHF module will initiate as Pic.4-2, if there is no error messages show up, then initiation process has been successfully finished.
-
Page 11: Chapter 3 Uhf Tag Scanning
MR16 User’s Manual V1.1 Chapter 3 UHF tag scanning Click SCAN on top of navigation bar to enter tags reading page. 3.1 Auto Scanning Select “Auto”, then click “Start” button to start tags scanning circularly, the information such as EPC or TID, Count, RSSI and Ant. - Page 12 MR16 User’s Manual V1.1 Pic.5-2...
-
Page 13: Single Scanning
MR16 User’s Manual V1.1 3.2 Single Scanning Select “Single” button and click “Start” to start scanning tag, EPC or TID, Count, RSSI and Ant.number will display on right side, as Pic.5- Pic.5-3... -
Page 14: Read Uhf Tag
MR16 User’s Manual V1.1 3.3 Read UHF Tag Click “READ” on top of navigation bar to enter page of tag reading. User could read data of 4 areas, RESERVED, EPC, TID and USER, setup address and data length, default password is “00000000”, click “Read”... - Page 15 MR16 User’s Manual V1.1 Comment: user could filter tags by setup address, data length and data in EPC, TID and USER areas, select “Enable” button to switch on filter function in Pic.6-2. Pic.6-2...
-
Page 16: Write Tag
MR16 User’s Manual V1.1 3.4 Write Tag Click “WRITE” on top of navigation bar to enter tag writing page. User could write data in RESERVED, EPC, TID and USER areas, setup start address and data length, input access password and data(hex), click “Write Data”... -
Page 17: Lock Tag
MR16 User’s Manual V1.1 3.5 Lock Tag Click “LOCK” on top of navigation bar to enter tag locking page. Input access password( DONOT input default password.), then click column of “Lock Code”, it will display window for selecting different methods of locking, click “OK” to generate lock code automatically, then click “Lock”... - Page 18 MR16 User’s Manual V1.1 Pic.8-2...
-
Page 19: Kill Tag
MR16 User’s Manual V1.1 3.6 Kill Tag Click “KILL” on top of navigation bar to enter operating page. Input access password (DONOT input default password.), click “Kill” button to destroy tags in Pic.9-1. Comment: user could filter tag by setup address, data length and data for selecting EPC, TID or USER area. -
Page 20: Uhf Module Version
MR16 User’s Manual V1.1 3.7 UHF Module Version Click 3 dots on top right of application and click “About” in list to check version of UHF module in Pic.10-1. Pic.10-1... -
Page 21: Module Temperature
MR16 User’s Manual V1.1 3.8 Module Temperature Click 3 dots on top right of application, click “Module temperature” in list to check UHF module temperature in Pic.11-1. Pic.11-1... -
Page 22: Chapter 4 Config
MR16 User’s Manual V1.1 Chapter 4 Config Click “CONFIG” on top of navigation bar to enter setup page. 4.1 Working mode User could setup different frequency band for different countries, as Pic.12-1, click “Set Frequency” to confirm frequency band. Click “Get Frequency”... -
Page 23: Output Power
MR16 User’s Manual V1.1 4.2 Output Power User could select different output power from 5 to 30dBm in Pic.12-2, click “Set Power” to confirm setup. Click “Get Power” to get current output power. Pic.12-2... -
Page 24: R2000 Settings
MR16 User’s Manual V1.1 4.3 R2000 settings Select ANT1-ANT8 to setup antenna, selected antenna will start functioning, unselected antenna will in OFF in Pic.12-3. Click “Set Antenna” to confirm setup, “Get Antenna” to check current antenna status. Pic.12-3... -
Page 25: Protocol
MR16 User’s Manual V1.1 4.4 Protocol There are two protocols can be selected in Pic.12-4, click “Set Protocol” to confirm. Pic.12-4... -
Page 26: Rf Link
MR16 User’s Manual V1.1 4.5 RF link There are four parameters can be selected in this parameter, as Pic.12-5. Click “Set link parameter” to confirm, click “Get link parameters” to check current RF link parameters. Pic.12-5... -
Page 27: Qt Tag
MR16 User’s Manual V1.1 4.6 QT Tag Select “Set QTPara” to switch ON and OFF hidden areas of QT tag, click “Get QTPara” to check current status. Pic.12-6... -
Page 28: Open Tagfocus
MR16 User’s Manual V1.1 4.7 Open tagFocus Select ON/OFF of tagFocus in Pic.12-6. 4.8 Open FastID Select ON/OFF of “Open the EPC and TID” in Pic.12-6. 4.9 Open EPC and TID Select ON/OFF of “Open the EPC and TID” in Pic.12-6.