Related Manuals for Marson MT1227
Summary of Contents for Marson MT1227
- Page 1 2D Wireless Barcode Reader Quick Guide 2D Wireless Barcode Reader Quick Guide (Rev1) P/N: 8013-0056000...
- Page 2 FCC WARNING STATEMENT WARNING AND CAUTION This equipment has been tested and found to comply with the limits for a Class B digital 1. Take any metals into contact with the terminals in connectors. device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 2.
-
Page 3: Specifications
OUT OF THE BOX INTRODUCTION Micro USB port Trigger Button (w/ Protective Cover) LED Indicator (1) iOS Hotkey Button (2) Delete Button Exit Window 2D Wireless SPECIFICATIONS Barcode Reader Quick Guide Light source 625nm red LED Scan rate 60 frames/sec Sensor 752 x 480 CMOS sensor Resolution... -
Page 4: Led Indication
BEEPER INDICATION GETTING STARTED Single long beep Power up Single beep Good read Single short beep The scanner reads a Code39 of ASCII in configuration procedure Two beeps i. Wireless connection ii. The scanner successfully reads a configuration barcode ... - Page 5 INTERFACE INTERFACE There are 5 interfaces for data transmission/collection: . E043$ *.E043$* BT HID 1. BT HID - Emulates a Bluetooth HID keyboard that transmits each barcode data to the host after decode. (See page 9) 2. BT SPP - Emulates a Bluetooth SPP device that transmits .
-
Page 6: Getting Connected
GETTING CONNECTED PINCODE SETUP There are two modes of wireless communication: . E043$ STEP 1 . E032$ [ Recommanded ] *.E043$* *.E032$* BT mode - HID Pincode Start 1. Press the trigger for 1 second to activate the scanner. 2. Scan [DISCONNECT] STEP 2 3. -
Page 7: Numeric Bar Codes
NUMERIC BARCODES *.31* *.36* *.32* *.37* *.33* *.38* *.34* *.39* *.35* *.30* - 11 - - 12 -... - Page 8 SMARTPHONE/TABLET CONNECTION SMARTPHONE/TABLET TOUCH KEYBOARD Getting Connected - iOS & Android Touch Keyboard - iOS iOS Hotkey Button 1. Press the trigger for 1 second to power up the scanner. 2. Scan below configuration barcode to clear last pairing record. .
- Page 9 POWER OFF TIMEOUT BINARY CHECK CHARACTER The timeout of inactivity before auto power-off. . E029$ *.e029$* Variable Timeout ENABLE . B030$ *.B030$* . E030$ SET MINUTE *.e030$* (Range: 00 ~ 60) DISABLE . B029$ *.B029$* SET SECOND Once enabled, a checksum will be added to the end of each data to conduct Xor calculation.
- Page 10 GENERAL SETTINGS READING MODE . A001$ . F002$ TRIGGER DEFAULT . P023$ . F005$ ABORT CONTINUOUS . A007$ . F006$ *.F006$* CHECK CONTINUOUS VERSION AUTO OFF BEEPER VIBRATOR . F012$ . D035$ *.D035$* VIBRATOR OFF BEEP OFF . F018$ . D034$ *.D034$* BEEP ON VIBRATOR ON...
- Page 11 KEYBOARD LAYOUT . C009$ . C010$ ENGLISH JAPAN (USA) (106 key) . C018$ . C025$ ENGLISH CANADIAN (UK) (FRENCH) . C034$ . C012$ CANADIAN FRENCH (TRADITIONAL) . C029$ . C011$ GERMAN NORWEGIAN . C026$ . C014$ ITALIAN SWEDISH . C031$ .
- Page 12 KEYBOARD LAYOUT . C017$ . C030$ CZECH BELGIAN (QWERTY) (AZERTY) . C022$ . C028$ CZECH DUTCH (QWERTZ) . C021$ . C027$ HUNGARIAN DANISH (QWERTZ) . C024$ . C032$ HUNGARIAN SLOVAK (101 KEY) . C033$ . C016$ SWISS BRAZILIAN (GERMAN) (PORTUGUESE) .
-
Page 13: Data Matrix
ENABLE SYMBOLOGIES . N017$ . A002$ ENABLE IATA ALL CODE . N010$ . L010$ GS1 DATABAR UK PLESSEY . G021$ . L001$ *.G021$* PDF417 . N001$ . G025$ *.G025$* INDUSTRIAL QR CODE 2 OF 5 . G027$ . M010$ *.G027$* MATRIX MICRO QR 2 OF 5... -
Page 14: Memory Mode
TERMINATOR MEMORY MODE . D012$ . C035$ *.c035$* Memory Mode . D011$ After scanning the above barcode, the scanner will be able to collect barcode data off-line. The barcode data will be stored in the format of: < Date >, < Time >, < Barcode Data > < CR > To retrieve stored data, please connect the scanner to the host with cable, . - Page 15 MEMORY MODE MEMORY MODE . R011$ . R006$ *.R006$* *.R011$* SET DATE DATA FORMAT The default Data Format is <Date>, <Time>, <Barcode Data> Example: To set Date to 2014-08-01 (Year-Month-Day): below are the codes for each item: 1. Scan [Set Date] 2.
- Page 16 MEMORY MODE MEMORY MODE . R008$ . R009$ *.R008$* *.R009$* DATE FORMAT TIME FORMAT The default Date Format is DD/MM/YYYY (Code = 09), below The default Time Format is HH:MM:SS (Code = 01), below is full list of available formats and their setup codes: are available formats and their setup codes: Code Format...
- Page 17 QR Code PDF417 DataMatrix - 31 - - 32 -...