Do you have a question about the H Series and is the answer not in the manual?
Questions and answers
Ron Griffin
August 6, 2025
We would like to purchase on Net 30 days account, as we are looking to get some items from your company. Please let us know the necessary steps and documentation required to set up the account. If you require any further information or have specific requirements for the account application, we would be happy to provide it promptly.
We look forward in hearing from you.
Best Regards
Ron Griffin
Purchasing Manager
SAFETY PRODUCT INC
KSL-H by KEELER CONTENTS INDICATIONS FOR USE ..................3 SAFETY ......................... 3 PHOTOTOXICITY ..........................3 WARNINGS AND CAUTIONS ......................4 CONTRAINDICATION ........................5 CLEANING AND DISINFECTION INSTRUCTIONS ............ 5 NAMES OF CONTROLS AND COMPONENTS ............6 ASSEMBLY ......................8 TABLE TOP AND BASE ASSEMBLY PROCEDURE ................8 ILLUMINATION TOWER ASSEMBLY PROCEDURE ................9...
Page 4
Use-by date Serial number Catalogue number Medical device Translation The Keeler Slit Lamp is designed and built in conformity with Directive 93/42/EEC, Regulation (EU) 2017/745 and ISO 13485 Medical Devices Quality Management Systems. Classifi cation: CE: Class I FDA: Class II The information contained within this manual must not be reproduced in whole or part without the manufacturer’s...
Brief description of the instrument This Keeler Slit Lamp can either be mounted onto a custom table top supplied by Keeler or can be mounted on a third parties table top (refraction unit) by suitably trained technicians. The Keeler Slit Lamp consists of 5 assemblies; illumination tower; observation system; XYZ translation base;...
Please note that the proper and safe functioning of our instruments is only guaranteed if both the instruments and their accessories are exclusively from Keeler Ltd. The use of other accessories may result in increased electromagnetic emissions or reduced electromagnetic immunity of the device and may lead to incorrect operation.
• Ensure the instrument or instrument table is placed on a level and stable surface. • Use only genuine Keeler approved parts and accessories or device safety and performance may be compromised. • Shut down after every use. In case the dust cover is used: risk of overheating.
KSL-H by KEELER 3. Surfaces must be carefully hand-dried using a clean non-shedding cloth. 4. Safely dispose of used cleaning materials. 4. NAMES OF CONTROLS AND COMPONENTS Headrest Assembly 1. Fixation light cable 2. Main lamp cable (4 pin socket) 3.
Page 9
KSL-H by KEELER 24. Joystick control (X Y Z movement) 25. Illumination control rheostat 26. Axle 27. Runner covers 28. R type tonometer mounting hole 29. Yellow fi lter knob (up = out) 30. Lock for securing magnifi cation body 31.
The refraction stand, combi unit or table leg must be IEC 60601-1 compliant. If you are fitting or have fitted your Slit Lamp to a medical or Keeler table leg / base ensure it is situated on a firm and level floor.
KSL-H by KEELER Runners 5.2 ILLUMINATION TOWER ASSEMBLY PROCEDURE 1. Remove the hex bolt (a) from the base of the Illumination tower, and then place the illumination tower on the Slit Lamp base with the base notch (b) and pin (c) aligned.
5.4 FITTING APPLANATION TONOMETERS, T TYPE AND R TYPES Keeler Applanation Tonometer (T-TYPE) 1. Position the guide plate in the tonometer / test bar support hole on the slit lamp.
Right eye Left eye Applanation Tonometer ‘Keeler Fixed’ (R-TYPE) This instrument is for those who wish the tonometer to remain permanently on the slit lamp. 5. Mount the plate for the tonometer onto the microscope body using the securing screw.
Parts of the slit lamp coming in to contact with the patient should be cleaned in accordance with these instructions prior to the examination. Keeler recommends the use of disposable hygienic chinrest tissues on the chinrest before the patients place their chin on it.
KSL-H by KEELER 3. Switch on the illumination, making sure the rheostat (25) is set to a low level to minimise the patient’s exposure to light hazard. 4. Rotate the joystick (24) until the light beam is at eye level.
The maintenance outlined below should only be carried out once the main power cable has been disconnected. If you have any problems that are not covered by the procedures described below, contact Keeler Ltd or your local supplier. 7.1 LED SYSTEMS LED’s typically have a life exceeding 10,000 hours of continuous use and therefore can be...
KSL-H by KEELER In the unlikely event of an LED failure please contact Keeler or your local distributor for guidance on the replacement procedure. 7.2 REGULARLY INSPECT THE DEVICE FOR DAMAGE OR DIRT Routinely clean as per section 3 on page 5 cleaning instructions.
There are no user serviceable parts in this instrument. Any servicing or repairs should only be carried out by Keeler Ltd. or by suitably trained and authorised distributors. Service manuals will be available to authorised Keeler service centres and Keeler trained service personnel.
9.2 ELECTROMAGNETIC IMMUNITY Guidance and manufacturer’s declaration – electromagnetic immunity The Keeler Slit Lamp is intended for use in the electromagnetic environment specified below. The customer or user should ensure that it is used in such an environment. Immunity test...
To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the Keeler Slit Lamp is used exceeds the applicable RF compliance level above, the Keeler Slit Lamp should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as re-orientating or relocating the Keeler Slit Lamp.
KSL-H by KEELER Rated maximum output Separation distance according to frequency of power of transmitter (W) transmitter (m) 150 kHz to 80MHz 80MHz to 800MHz 800MHz to 2.7GHz d = 1.2√ p d = 1.2√ p d = 2.3√ p 0.01...
Page 22
KSL-H by KEELER Base travel 25mm Z-axis, 107mm X-axis, 110mm Y axis Horizontal fine adjustment 12mm Table top dimensions 405 x 500mm Fixation lamp Light source LED output power 160K (+/-20%) Weight, packed (approx.) Slit Lamp with chinrest 20.0Kg, 75 x 54 x 45cm W x D x H Table top with PSU &...
Page 23
KSL-H by KEELER Environmental Conditions: 1060 hPa °C °C 800 hPa Shock (without packing) 10 g, duration 6 ms STORAGE CONDITIONS 1060 hPa °C °C 700 hPa TRANSPORT CONDITIONS 1060 hPa °C °C 500 hPa Vibration, sinusoidal 10 Hz to 500 Hz: 0.5g...
3020-P-7000 Keeler KAT T-Type 2414-P-2030 Applanation Tonometer Keeler KAT R-Type 2414-P-2040 Applanation Tonometer Keeler D-KAT T-Type Digital Keeler 2414-P-2032 Applanation Tonometer Keeler D-KAT R-Type Digital Keeler 2414-P-2042 Applanation Tonometer 11. PACKAGING AND DISPOSAL INFORMATION Disposal of old electrical and electronic equipment This symbol on the product or on its packaging and instructions indicates that this product shall not be treated as household waste.
Page 26
Contact Manufacturer Keeler Limited Clewer Hill Road Windsor Berkshire SL4 4AA UK Freephone 0800 521251 Tel +44 (0) 1753 857177 Fax +44 (0) 1753 827145 USA Sales Office China Office Keeler USA Halma China Group 3222 Phoenixville Pike 名称:沃迈(上海)机电有 Building #50 限公司...
Need help?
Do you have a question about the H Series and is the answer not in the manual?
Questions and answers
We would like to purchase on Net 30 days account, as we are looking to get some items from your company. Please let us know the necessary steps and documentation required to set up the account. If you require any further information or have specific requirements for the account application, we would be happy to provide it promptly. We look forward in hearing from you. Best Regards Ron Griffin Purchasing Manager SAFETY PRODUCT INC