Table of Contents
Advertisement
Programmable room thermostat settings
When the Holiday function is set, via this program, the function
will become active at midnight of the day set and inactive at
midnight on the last day set.
During the holiday period the hot water and CH functions are
off and will return to normal operation at the end of the holiday
period. The Frost symbol is displayed, indicating that the boiler
is OFF but is protected when the temperature falls below 5 °C.
To cancel the holiday function:
▶ Press the menu key for more than three seconds to enter
user menus and select Holiday, ON will be displayed.
▶ Press the knob and ON flashes, turn the knob to select OFF
▶ Press the knob to confirm OFF
▶ Press the return button
5.1.4 Info
Turn the knob to select Info and press the knob, two menus are
available:
1. DHW
2. Signal strength
DHW
1. Turn the knob to select DHW and press to enter. The
current temperature of the DHW is displayed:
a. Actual temp
▶ Press the Return button to go back to DHW
Signal strength
Turn the knob to select Signal strength and press the knob to
enter the function.
The signal strength is displayed as a number from 0 to 10 in the
area where the temperature is normally displayed.
0
= no signal
1 - 3
= weak signal
4 - 6
= acceptable signal
7 - 10 = very good signal
5.1.5 Setting
▶ Turn the knob to select Settings and press to enter the
function. Three sub programs are displayed:
1. Language
2. Time/date
3. Format
4. Reset all
1. Language
This function allows you to choose the language used by the
Programmer, by default is set to English (EN).
▶ Turn the knob to select language, EN flashes, select either:
– EN (English)
– NL (Dutch)
– dE (German)
▶ Press the knob to confirm the desired language
12
to go back to the normal display
2. Time/Date
This function allows the current time and date to be set, this
would be used on initial set up of the Programmer or if the time
and date were lost due to the boiler being switched off for an
extended period of time.
Turn the knob to select Time/date and press to enter the
function:
▶ Press the knob to select clock time
▶ Press the knob and the hours flash
▶ Turn the knob to select the correct hour
▶ Press the knob to confirm the selection and minutes flash
▶ Turn the knob to select the correct minutes
▶ Press the knob to confirm the selection
▶ Turn the knob to display the date set up
▶ Press the knob to select the function, the day flashes
▶ Turn the knob to select the correct day
▶ Press the knob to confirm the correct day and the month
flashes
▶ Turn the knob to select the correct month
▶ Press the knob to confirm and the year flashes
▶ Turn the knob to select the correct year
▶ Press the knob to confirm to set the year
▶ Turn the knob to display the DST (Daylight savings time)
▶ Press the knob and ON flashes
▶ Turn the knob to select ON or OFF
▶ Press the knob to confirm the selection
▶ Press the return button
turn the knob to select Format
3. Format
Press the knob to enter the format function and the following
sub menus are available:
1. Date format
2. Time format
3. Sensor calib.
4. Contrast
Date format
This function allows you to change the way the date is
displayed, by default the format is DD.MM.YYYY. Once the date
and time have been set the date format can be set:
▶ Turn the knob to select the Date format function
▶ Press the knob to show the date format flashing
▶ Turn the knob to select either:
▶ DD.MM.YYYY
▶ MM/DD/YYYY
▶ When the desired format for the date has been selected,
press the knob to confirm and wait a few seconds for the
display to return to Date format
to go back to Time/date and
Comfort II– 6720810965 (2017/02)
Advertisement
Table of Contents
