Follett Horizon Elite 1810 Series Installation Instructions Manual
Hide thumbs
Also See for Horizon Elite 1810 Series:
- Quick start manual (8 pages) ,
- Operation and service manual (52 pages) ,
- Installation instructions manual (17 pages)
Table of Contents
Advertisement
Quick Links
HCD/HMD/HCF/HMF1810RBT, HCD/HMD/HCF/HMF2110RBT,
HCD1810NBT, HMD1810NBT, HCD2110NBT, HMD2110NBT
(See model number configurator on page 2 for details.)
Order parts online
www.follettice.com
Horizon Elite
™
for Ice Storage Bin Top-mount Applications
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Ice Machine Installation Instructions
remote condensing
01157908R03
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Follett Horizon Elite 1810 Series
Summary of Contents for Follett Horizon Elite 1810 Series
- Page 1 Horizon Elite Ice Machine Installation Instructions ™ for Ice Storage Bin Top-mount Applications HCD/HMD/HCF/HMF1810RBT, HCD/HMD/HCF/HMF2110RBT, HCD1810NBT, HMD1810NBT, HCD2110NBT, HMD2110NBT (See model number configurator on page 2 for details.) Order parts online www.follettice.com remote condensing 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 •...
- Page 2 Chewblet Ice Machine Model Number Configurations ® 1810 Application Configuration Icemaker Voltage Series Condenser MC Maestro™ C 208-230/60/1 (icemaking head) 425 up to A Air-cooled, self-contained V Vision™ S RIDE™ Self-contained only. 425 lbs Chewblet ® W Water-cooled, self-contained H Harmony™ (RIDE remote D 115/60/1 (icemaking head) (193 kg)
- Page 3 Read and complete the following 8 installation steps Unpack Site preparation Bin preparation Docking assembly Ice transport tube External connection Internal connection Front cover BIN • TOP-MOUNT remote condensing...
-
Page 4: Unpack Ice Machine
Unpack Carefully unpack and inspect the contents of your Follett ice machine. Unpack ice machine ➋ ➌ ➊ ➎ ➍ 7/16" DO NOT TILT ICE MACHINE TO ACCESS BOLTS! COMPRESSOR DAMAGE 7/16" WILL RESULT ➐ ➏ BIN • TOP-MOUNT remote condensing... -
Page 5: Prepare The Installation Site
• 10-70 psi (69-483kpa) • 45-90 F (7-32 C) • Follett recommends the use of an in-line water filtration system (item# 00130286) • This equipment is to be installed with adequate backflow protection to comply with applicable federal, state, and local codes ➌... -
Page 6: Before Proceeding
Bin preparation Prepare the bin. Bin top preparation Bin top preparation — – ˜ – • Remove protective tape from ➊ • Apply gaskets gaskets ➋ • Install shuttle actuator through bin top and secure with locking nut ➌ BEFORE PROCEEDING Prior to installing the docking assembly, ensure that the drain fitting is oriented (right or left) correctly for your installation. - Page 7 Docking assembly Install the docking assembly. Docking assembly 2" (50,8 mm) 1.81" (46 mm) ➋ 3/8˝ ∅ 2" (50,8 mm) high pressure Stub Typ line 3.75" (95.3 mm) 7/8" ∅ low pressure line • Mount docking assembly ➊ • “Rough-in” the refrigerant piping ➋...
-
Page 8: Ice Transport Tube
Ice transport tube Install the ice transport tube. Ice transport tube installation. ➋ Hot Water 160 F (71 C) ➊ ➌ • Slide insulation onto ice transport tube • Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers ➊... -
Page 9: External Connections
External connections Connect utilities to docking assembly. Chassis drain plumbing - required Water and drain ➊ ➋ ➌ Minimum 8" ➏ radius • Plug must be removed from John Guest 2 ft. x 1" OD fitting. silicone tubing • Route 3/8" drain tubing through knockout in back of docking station and insert fully into John Guest fitting connection at the 3/4"... -
Page 10: Internal Connections
Internal connections Connect docking assembly to ice machine. Ice transport tube installation Water line ➋ ➊ ➌ Mount water ➋ solenoid ➊ • Slide ice machine into docking assembly • Mount water solenoid to inside rear of ensuring that drain tube is fully seated on docking assembly using one screw ➊... - Page 11 Power cord TDS switch HIGH CLEAN • Position plate into opening and secure • Set the TDS switch on the electrical box: with supplied screw HIGH: for extended service life LOW: for low-scale water BIN • TOP-MOUNT remote condensing...
-
Page 12: Front Cover
Consult Operation and Service Manual provided with ice machine for sanitizing instructions. Horizon, Horizon Elite, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge and Vision are trademarks of Follett Products LLC. Chewblet, RIDE and Follett are registered trademarks of Follett Products LLC, registered in the US.
Need help?
Do you have a question about the Horizon Elite 1810 Series and is the answer not in the manual?
Questions and answers