LW MEASUREMENTS CSS220 Instruction Manual

Function Specification
Specification
9.2 Press "[UNIT]" key to select auto-on(BALIAt), Backlight on(BALIon) and
1. Weighing
Backlight off(BALIoF) Compact Shipping Scale
Press and hold key to turn on the scale, LCD display shown "5095" and
9.3 Press "[HOLD/TARE]" key to confirm.
Model number
return to "0.00". Place an object onto the platform, once weighing is stable,
CSS220
LCD display will show the weight and the stable symbol "◎".
10. One Point Calibration
L C D d s i p a l y
2. Kg/Lb/Lb:oz Conversion
10.1 Once the scale is on, press and hold "PCS" and "UNIT" for 2s to access
Instruction Manual
N e / t G o r s s w e g i t h
turn on the Scale, press "[UNIT]" key to switch KG, LB and LB:OZ.
into the calibration selection.
Package
Press and hold "[UNIT]" key for 20seconds, unit symbol on the display will
10.2 LCD display shown "C-kg".
2 Units in one box:50.8x0.75x33.5 (cm
be flashing for 3times, current unit locked. Press and hold "[UNIT]" key for
10.3 Press "[UNIT]" key to select between "C-kg" and "C-lb" and press
Operating/Storage
20seconds to release.
"[HOLD/TARE]" to confirm.
Temperature
3. Auto/Non-Automatic Power-Off Function
10.4 LCD display shown "C-XX" (remind user to place an equivalent weight
P o w r e s o u c r e
Press and hold "[UNIT]" key, and turn on the Scale, the display will show
on the scale).
"An-OF", then back to "0.00", Non-automatic power-off function is active
10.5 KG: "C-50" and "C-100", LB: "C-100" and "C-200".
now.
10.6 Press "[HOLD/TARE]" to confirm and turn off the scale.
Auto power-off will be restored once the Scale restarted, and auto turning
10.7 Press "[HOLD/TARE]" and "[UNIT]", and press ""[ON/OFF]" to turn on
off time is 2minutes.
the scale.
4. Low Power Detection
10.8 LCD display shown "CAL" and shown "r-200".
If the voltage is lower than 3.7v(Temporary), LCD will show "LobAtt" to
10.9 Press "[UNIT]" to select the correct capacity of the scale and press
remind user to change batteries, and Scale will turn off automatically after 2
"[HOLD/TARE]" to confirm. (CSS440 refer to "r-200")
seconds.
10.10 LCD display shown the internal code (5000-15000) and press
5 HOLD function
"[HOLD/TARE]" to confirm.
Once reading is stable, press "[HOLD/TARE]" key, current reading has
10.11 LCD display shown "C-XX" (according to the setting set on 10.5).
been locked. Removed the object from the platform, Scale will back to "0.00"
10.12 Place an equivalent weight as display shown and pressing
after 5seconds.
"[HOLD/TARE]" to confirm once reading is stable.
Turn on the Scale, press and hold "[HOLD/TARE]" key for 2seconds to
10.13 LCD display shown "END" = completed or "Err1" = failed and turn off
access into the Manual hold mode (Hn-Ao). Press and hold "[HOLD/TARE]" key
the scale automatically.
for 2seconds again to switch to Auto hold mode (H-Ao).
Capacity Division
440lb 0.1lb
0 8 . n i c h L C , D 6 d g i s t i
8 9 . 9 / 3 . k g
3
Standard carton: 53x16.3x35.5(cm )
5-35 (41 -95 ) / 0 -60 (32 -140 )
℃ ℉ ℃ ℉
6 X A A r o A C A d a t p r o
3 5 7 1
296*210mm
6 PCS count function

Description

6.1 Once the scale is on, press and hold "[PCS]" key for 2seconds to
Saftety Precautions
access into the sampling setting. LCD display will show the number and "Lo"
repeatedly.
6.2 Press "[UNIT]" key to select "5 pieces", "10 pieces", "20 pieces", "25
pieces", "50 pieces", "75 peices" and "100 pieces" sampling size.
6.3 Place the numbers of object on the platform which LCD display shown.
Avoid installing the scale in direct sunlight, this may cause discoloration or
6.4 If there is appropriate weight on the platform, scale will stop flashing
malfunctions.
after 3seconds
3
)x
6.5 If the weight on the platform is not appropriate the setting size, LCD
Do not mix the type of batteries. Replace all other batteries at the same
display will the number and "LO" for 10second, then automatically return to
time.
normal weighing mode.
6.6 Once the scale is on, press "[PCS]" key to access into the previous
If the scale is not to be used for a long period of time, remove all batteries setting.
from the battery compartment to avoid leakage which may cause damage
7 Tare function
to the instrument.
Place an object on the platform, once reading is stable, press and hold
"[HOLD/TARE]" key for 2seconds, LCD shows "0.00", Tare function is on. "
Avoid overloading, it could cause damage to the scale.
Place another object on the platform, display shows only the weight after
Tare. The maximum capacity Is the summary of the weights before and
Do not drop water onto the scale as it's not a water-resistant unit. If inside of
after Tare. If Scale over loaded, display will show "oooooo" and turn off
the scale is wet, it may damaged.
automatically after 10seconds.
8 Overload indication
One loading is over, LCD shows "oooooo" and turn off automatically after
10seconds.
9 Backlight selection
9.1 Once the scale is on, press and hold "[HOLD/TARE]" and "[UNIT]" key
for 2second to access into the backlight selection.
Caution
6 4 2