Using Your Steam Pocket Mop; Intelligent Steam Control; Mop - Shark KLIK N' FLIP S6003EUDB Owner's Manual

Using Your Steam Pocket

Mop

®
IMPORTANT: Make sure you do not use the Steam Mop without attaching a Dirt Grip pad and adding water to the water tank first. When you are
using the Steam Mop for the first time, it might take longer than the normal 30 seconds to start steaming.
IMPORTANT: Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with wax and on some no-wax floors, the
sheen may be removed by the heat and steam action. Test an isolated area of the surface to be cleaned before proceeding. Check the use and care
instructions from the floor manufacturer.
fig. 9 fig. 10
NOTE: To prolong the life of your Steam Mop, we recommend
using distilled water.
NOTE: Sweep or vacuum your floors prior to cleaning with your
Steam Mop.
1
Twist the Quick-Release Cord Holder to unwrap the power cord
completely. (fig. 9) Plug into an electrical outlet.
2 When it' s first plugged in, the unit will be in Standby mode. The 3 lights
below the Steam Control Button will blink to indicate Standby mode.
3 To select the steam mode, press the Steam Control Button once
for LOW (1 blue light) twice for MED (2 blue lights) or three times
for HI (3 blue lights).
4 Clean your floors with a forward and backward motion.
5 When you need an extra burst of steam to clean a stuck-on stain,
you can use the Steam Blaster feature. Flip the head over so that
it is behind the mop body, then tilt the mop handle down. This
will cause the the Steam Blaster (fig. 10) to emit a concentrated
blast of steam onto the stain.
CAUTION: While in Steam Blaster mode, do not leave stationary
for more than one minute.
CAUTION: Do not scrub any one area for an extended period of time.
6 To stop the Steam Blaster spray, simply raise the handle. You can then
flip the mop head back into its original position and continue cleaning.
7 When finished mopping, press the Steam Control Button. The
three blue lights will blink, indicating that the unit is in Standby
36
fig. 11a
fig. 11b
mode. Once in Standby mode, unplug the unit.
8 To remove the Dirt Grip pad, simply lift the Steam Mop straight
up by the handle until the Klik n' Flip® Mop Head is hanging
straight down. Press the Release button on the back of the Steam
Mop body (fig 11a), and both sides of the head will drop open,
releasing the pad. (fig 11b)
9 Once the Dirt Grip pad has been released, close the Klik n' Flip® Mop
Head. To close, gently press one side of the Klik n' Flip® Mop Head to
the floor until that side clicks into place. Repeat on the other side.
10 When the water tank is empty, the Steam Mop will stop
producing steam. You can refill the water tank at any time as
long as the Steam Mop is unplugged. Follow the water tank filling
instructions on page 35.
NOTE: Please wait 2 to 3 minutes for the Steam Mop to cool off before
switching the mop head. Never leave the Steam Mop with a damp/
wet Dirt Grip pad on any floor for an extended period of time.

Intelligent Steam Control

The Shark ® Klik n' Flip® Steam Pocket ® Mop has 3 unique Intelligent Steam Control settings so you can use the right amount of steam for the
cleaning task at hand. See below for tips on when to use each setting.
SETTING IDEAL FOR THESE SEALED SURFACES
LOW
Laminate
Hardwood
Marble
MED
Hardwood
Marble
Tile
Stone
HI
Hardwood
Marble
Tile
Stone
For an extra burst of steam, you can use the Steam Blaster feature in LOW, MED and HI. Follow the instructions
Steam Blaster
found on the "Using your Steam Pocket
TO SANITIZE* WITH THE STEAM MOP USING THE KLIK N' FLIP® MOP HEAD AND THE DIRT GRIP
1
Attach a clean Dirt Grip pad to the Klik n' Flip® Mop Head.
2 Plug in the unit and press the Steam Control Button to select the HI Setting.
3 Wait 30 seconds for the unit to begin producing steam.
4 Start mopping on an appropriate sealed hard-floor surface with a forward and backward motion. After three minutes, your unit is ready to be
used to sanitize.
5 Using a forward and backward motion, move the unit over the area you seek to sanitize. Repeat at least 5 times.
* Sanitization studies were conducted under controlled test conditions. Household conditions and results may vary. With Klik n' Flip® Mop in HI
mode only when used with Steam Mop. Not in Steam Blaster mode.
RECOMMENDED USAGE
Cleaning delicate surfaces
Light cleaning and dusting
Loosening and lifting light dirt
Cleaning sealed surfaces and large areas
Basic, everyday cleaning
Removing spots and smaller messes
Cleaning moderate and heavy traffic areas
Deep cleaning and cleaning hard-to-clean surfaces
Tough cleaning and removing stuck-on messes and stains
Deep cleaning heavy traffic areas
Cutting through heavy dirt and grime
Mop" page.
®
PAD:
™
s h a r kc l e a n . e u 37