Contents 1.General Introduction 1.1 Welcome ..............................1.2 Use of Manual ............................1.3 Service and Technical Support ......................... 1.4 Bike Components ............................1.5 Technical Data ............................2.Installation and Adjustment 2.1 Handlebar and Stem Assembly ........................ 2.2 Front Wheel Installation ..........................2.3 Pedal Installation ............................2.4 Seat Position ..............................
You should keep this manual along with any other documents that were included with your bicycle. All content in this manual is subject to change without notice. Magnum Bikes makes every effort to ensure accuracy of its documentation and assumes no responsibility of liability if any errors or inaccuracies appear within.
General 1.General Introduction 1.5 Technical Data Component Peak T5 Motor 48V, 500W Bafang Rear Geared Hub Motor Battery 48V 15Ah Lithium Ion Display Magnum LCD Display Throttle/PAS Thumb Throttle, Torque Sensor Front Fork SR Suntour XSM34 Boost with Lockout & Preload Adjustment...
Installation & Adjustment 2.Installation and Adjustment 2.1 Handlebar and Stem Assembly Remove the faceplate from the stem with a 4mm Remove the display for easy installation. Lift the allen key. handlebars (attached to the cables and display) and center them with the head tube. Attach the faceplate using a 4mm allen key.
Installation & Adjustment 2.Installation and Adjustment 2.2 Front Wheel Installation Place the front wheel between the fork. Insert axle into non-drivetrain side. Use a 6mm allen key to tighetn the axle. 2.3 Pedal Installation Identify your pedals: check the letters on the pedals, “L” or “R”. The “R”...
Installation & Adjustment 2.Installation and Adjustment 2.4 Seat Position To enable comfortable, fatigue-free and safe riding, the saddle and handlebar height should be adjusted to the body size of the rider. The saddle height is correct if the leg is near full extension while the foot is resting flat on the pedal in the bottom position of the crank cycle.
Installation & Adjustment 2.Installation and Adjustment 2.5 Saddle Height & Adjustment The quick-release lever must require noticeable effort to put into fully closed position to prevent any unde- sired movement while riding. WARNING An improperly closed quick release lever can open again or have limited ability to keep the saddle in place. This may cause the saddle to suddenly drop into the seat tube, potentially leading to serious falls and injury.
Installation & Adjustment 2. Installation and Adjustment 2.6 Fork Adjustment Rotate the lever (1) to lock the suspension. 2.7 Brakes The front and rear brakes operate independently of each other. When stopping or slowing down, use both brakes at the same time. The left brake lever (1) controls the front brake.
Spokes (1) can loosen over time. It is important to maintain proper spoke tension to prevent breaking spokes. Broken spokes should be replaced immediately and the wheel must be trued. Replacing, re-tensioning, and truing of the wheel or spokes should be done by a Magnum dealer or bike specialist.
Battery & Charger 3.Battery and Charger 3.1 Overview Battery Lock Power Button Battery Level WARNING Please ensure that the battery is locked in place before use AC Plug¹ Charger Charging Indicator Battery Plug ¹Type will vary 3.2 General Remarks Stop charging the battery immediately if you notice anything unusual, such as smoke or a strange smell; take out the battery and store it outside of the house, then take the battery to an authorized dealer or experi- enced technician for service or replacement.
Display 4. Display 4.1 Appearance Powering ON/OFF Press and hold the power button to turn ON the display. A start-up screen (see image below) will display for approximately 2 seconds before entering the main interface showing real-time information. To turn the display OFF press and hold the power button until the screen goes blank. The display will turn off automatically if no operations are performed within the set sleep time, while the speed is 0, and current is less than 1A.
Page 14
Display 4. Display 4.2 Indicators & Buttons Walk Assist Indicator Service Tool Connection Error Code Bluetooth Battery Level Indicator Light Indicator Power Output Speed Mph Trip Information & Indicators PAS Levels Adjust Up Mode Function Adjust Down Power On Button Functions Power ON: Turns the display ON/OFF Adjust Up/Down: Changes the level of pedal assist during riding and switches functions in display settings Mode Function: Switches interface functions and enters into the display settings...
Page 15
Display 4.Display Pedal Assist Level Short press the arrow buttons to adjust the pedal assist level up or down. There are 5 PAS levels: ECO, TOUR, SPORT, TURBO, BOOST, and BOOST+. BOOST+ is indicated by a blinking BOOST icon. When PAS level is empty it means pedal assist is off.
Page 16
Display 4.Display Trip, Odometer, & Range Short press the M button to switch from TRIP, ODO, & RANGE on the display. The cycle order is TRIP/AVG, ODO/MAX, then RANGE/AVG. After 5 seconds with no operation preformed on the M button and the bike speed greater than 0 the display screen will switch back to the main interface.
Page 17
Display Battery Power Battery power is shown by a battery bar indicator and percentage. The battery bar divides the power level into 5 bars. After battery capacity is lower than 5% the display enters low voltage mode. In this mode the battery level shows 0 bars.
Page 18
Display Display Settings The following description explains how users can access the settings options in their display. Within 10 seconds of turning on the display, long press the M button to enter the settings interface. Short press the arrow buttons to switch between settings. Short press the M button to enter a specific setting.
Page 20
Display Data Clearance Within 10 seconds of turning on the display, when the display shows the TRIP interface, long press the M button to show TRIP data. While the TRIP icon is blinking short press the M button to confirm data clearance. To exit long press the M button.
Page 21
Error Code Table Each error code corresponds to a specific fault in the system. The table below is intended for the e-bike own- er to use as reference when working with Magnum Bikes technical support or a certified Magnum dealer. Error Code...
Recommendations & Maintenance 5. Recommendations and Maintenance 5.1 General Requirements E-bikes use metal shells to cover the electric components, so we strongly advise against the use of exces- sive water to wash the shells and parts around them. Use a soft cloth with a neutral solution to wipe the dirt off the shells.
Recommendations & Maintenance 5.3 Definition of Tampering and Recommendations Category 1 Components which can only be replaced after approval from the bicycle manufacturer/ electronic system provider Motor Controller Electric Cables Battery Sensors Display Controls Display Battery Charger Category 2 Components which can only be replaced after approval from the bicycle manufacturer Frame Hub-motor Wheel Brake Pads...
Warranty 6. Warranty Your Magnum E-bike comes with a limited warranty. Please visit www.magnumbikes.com or your local Mag- num dealer for details. Bike must be registered at www.magnumbikes.com/warranty in order to be covered by the one year warranty. Stay Connected...