Advertisement
Advertisement
Table of Contents
Related Manuals for New Holland MZ19H
Summary of Contents for New Holland MZ19H
- Page 1 REPAIR MANUAL MZ19H 87045364 2/04...
- Page 2 SECTION 8 - ELECTRICAL SYSTEM The sections used through out all New Holland product Repair manuals may not be used for each product. Each Repair manual will be made up of one or several books. Each book will be labeled as to which sections are in the overall Repair manual and which sections are in the each book.
-
Page 3: Section 1 - General Information
SECTION 1 - GENERAL INFORMATION SECTION 1 - GENERAL INFORMATION CONTENTS Section Description Page General Information ....................1-2 Think Safety First....................... 1-2 Engine Specifications - (MZ19H) ................1-3 Bolt Torques....................... 1-7 Maintenance Schedule - (MZ19H)................1-8 Find manuals at https://best-manuals.com... -
Page 4: Think Safety First
This manual is intended as a service and repair manual only. The safety instructions provided herein are for troubleshooting, service, and repair of the MZ19H zero radius tractor. The MZ19H zero radius tractor and attachment operator's manuals contain safety information and operating tips for safe operating practices. -
Page 5: Specifications
SECTION 1 - GENERAL INFORMATION SPECIFICATIONS MZ19H ENGINE Type............... Kawasaki Model............. FH580V Horsepower ........... 14.2 kw (19)@3600 RPM Cylinders............V-Twin Displacement..........585CC (35.7 cu. in.) Low Idle Speed..........1400 RPM Maximum Speed: High Idle ............ 3400 RPM Oil Capacity ........... - Page 6 SECTION 1 - GENERAL INFORMATION MZ19H TIRES Rear Drive Tires ..........18 x 10.5-10 4 ply with “Multitrac CS” tread Front Castor Tires.......... 410/350 x 4 with “sawtooth” tread Tire Pressure ..........13 psi (90 kPa), rear, 35 psi (241 kPa) front OPERATORS SEAT Type...............
- Page 7 SECTION 1 - GENERAL INFORMATION MZ19H LUBRICATION FITTINGS Front Castor Pivots........2 Fittings Front Castor Wheels........2 Fittings Lift Assembly ..........3 Fittings Deck Idler Pivot ..........1 Fitting Transaxle Idler Pivot........1 Fitting Control Linkage Pivot ........2 Fittings DIMENSIONS Wheel Base ...........
- Page 8 SECTION 1 - GENERAL INFORMATION MZ19H GAUGE WHEELS One on each front corner, one on each rear corner to reduce scalping. Gauge wheels have four height position adjustments. HEIGHT OF CUT Adjusts from 1.5” to 4.5” (38 to 114 mm) (7 positions) UNCUT CIRCLE 0”...
- Page 9 SECTION 1 - GENERAL INFORMATION BOLT TORQUES DESCRIPTION TORQUE Blade to Spindle 80 - 100 ft lb (109 - 136 N·m) Caster Bolts 77 - 95 ft lb (105 - 130 N·m) Clutch Bolt 50 - 60 ft lb (68 - 82 N·m) Engine Mounting Bolts 120 - 180 ft lb (164 - 246 N·m) Spindle Pulley Nuts...
- Page 10 SECTION 1 - GENERAL INFORMATION MAINTENANCE SECHUDLE (MZ19H) MAINTENANCE PROCEDURE SERVICE INTERVAL Check the engine oil After first use Check the engine oil level Check the safety system Each use Clean the air intake screen Clean the mower housing Check the cutting blades...
-
Page 11: Section 2 - Model/Serial Number Location
SECTION 2 - MODEL/SERIAL NUMBER LOCATION SECTION 2 - MODEL/SERIAL NUMBER LOCATION CONTENTS Section Description Page Model/Serial Number Location .................. 2-2... - Page 12 SECTION 2 - MODEL/SERIAL NUMBER LOCATION MODEL/SERIAL NUMBER LOCATION The unit model and serial number plates is on the frame under the seat as shown in the illustration. The engine has its own model and serial number identification. Consult the appropriate engine manufacture’s service literature for the location and translation of the engine model and serial number information.
-
Page 13: Section 3 - Greasing And Lubrication
SECTION 3 - GREASING AND LUBRICATION SECTION 3 - GREASING AND LUBRICATION CONTENTS Section Description Page Service Interval/Specification ..................3-2 Lubrication Points ...................... 3-3... -
Page 14: Service Interval/Specification
The unit should be greased every 25 hours; more often when operating in dirty, dusty, or sandy conditions. A decal located under the seat shows the location of all the grease zerks. Grease Type: New Holland Ambra GR-9 multi- purpose grease (General-purpose lithium base grease). -
Page 15: Lubrication Points
SECTION 3 - GREASING AND LUBRICATION LUBRICATION POINTS There is a grease fitting on the mower for right and left outer spindle. The grease zerk for the center mower spindle. There is a grease fitting for the deck idler arm bushing. - Page 16 SECTION 3 - GREASING AND LUBRICATION There are two grease fittings for the deck raising pivot bushings - one on each side of the unit. The grease zerk for the deck height adjustment lever is on the right side of the machine. There are grease fittings for each front castor bushing,...
- Page 17 SECTION 3 - GREASING AND LUBRICATION as well as the castor wheel bearings. The zerk fitting for the traction belt idler bushing is located under the seat. Also under the seat are the fittings for the motion control lever pivot bushings - one for each lever.
- Page 18 SECTION 3 - GREASING AND LUBRICATION...
-
Page 19: Section 4 - Engine
SECTION 4 - ENGINE SECTION 4 - ENGINE CONTENTS Section Description Page Kawasaki Engine ....................... 4-2 Kawasaki Air Cleaner ....................4-2 Spark Plug ......................... 4-3 Engine Remove and Replace ..................4-4... - Page 20 SECTION 4 - ENGINE KAWASAKI ENGINE Oil Type: New Holland Ambra Super Gold detergent oil (API service SC, SD, SE, SF, SG, or SH). Crankcase Capacity (with filter): 1.6 qt. (1.5 l). Viscosity: See table. Change Oil: • After the first use.
- Page 21 This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...
Need help?
Do you have a question about the MZ19H and is the answer not in the manual?
Questions and answers