Table of Contents
Advertisement
Quick Links
ERGODESK
AUTO SERIES
USER MANUAL
PRODUCT MAY VARY SLIGHTLY FROM THE ITEM PICTURED DUE TO MODEL UPGRADES.
READ ALL INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT.
RETAIN THIS OWNER'S MANUAL FOR FUTURE REFERENCE.
NOTE:
THIS MANUAL MAY BE SUBJECT TO UPDATES OR CHANGES. UP TO DATE MANUALS ARE AVAILABLE THROUGH OUR
WEBSITE AT WWW.LIFESPANFITNESS.COM.AU
Advertisement
Table of Contents
Related Manuals for LifeSpan ERGODESK AUTO Series
Summary of Contents for LifeSpan ERGODESK AUTO Series
- Page 1 ERGODESK AUTO SERIES USER MANUAL PRODUCT MAY VARY SLIGHTLY FROM THE ITEM PICTURED DUE TO MODEL UPGRADES. READ ALL INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT. RETAIN THIS OWNER’S MANUAL FOR FUTURE REFERENCE. NOTE: THIS MANUAL MAY BE SUBJECT TO UPDATES OR CHANGES. UP TO DATE MANUALS ARE AVAILABLE THROUGH OUR WEBSITE AT WWW.LIFESPANFITNESS.COM.AU...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Important Safety Instructions ....... 03 II. Product Technical Data ........05 III. -
Page 3: Important Safety Instructions
I. IMPORTANT SAFETY INSTRUCTIONS WARNING: Please read this manual before operating this equipment. NOTE Please use this equipment according to the instructions in this brochure to avoid accidents. • Keep children and pets away from the electric height-adjustable desk during the operation. Unplug the power cord during a thunderstorm or if you do not intend to use the desk for a long time. - Page 4 • DO NOT use this equipment in case of failure! • Before checking or wiping this equipment, please turn off the power! • Please DO NOT use water or alcohol to clean the equipment! • The company does not bear any warranty or liability for damage and human injury caused by any abnormal operation.
-
Page 5: Product Technical Data
II. PRODUCT TECHNICAL DATA ITEM Data Input 220~240VAC / 100~130VAC 50~60Hz Output 29VDC Max Loading 220 lbs / 100 kg Height Range (Without Desktop) 27.6"~47.3"/70CM~120CM Working Ability 2 Min / 20 Min IMPORTANT ELECTRICAL INFORMATION |... -
Page 6: Parts List
III. PARTS LIST Name Qty. Name Qty. Foot M6*30 Bolt Column ST4.8*16 Screw Side Bracket ST2.9*15 Screw Right Tube Power Cord Left Tube Power Adapter Extension Tube Control Box M6*8 Bolt Extension Cable M6*10 Bolt Cable Clip | PARTS LIST... -
Page 7: Assembly Instructions
IV. ASSEMBLY INSTRUCTIONS NOTE: This step has been pre-installed before shipment, please check for missing spare parts and adjust the frame expansion tube to the appropriate length. M6*8 bolts Left Tube Right Tube Extension Tube Extension Tube Avoid excessive tightening of bolts. STEP 1 1. -
Page 8: M6*10 Bolt
Fasten the bolts M6*10 bolts Avoid excessive tightening of bolts. STEP 2 1. Insert the columns into the space which is between the left and right tubes respectively, line up the holes on the frame and column. 2. Tighten the bolts. Side bracket Fasten the bolts M6*10 bolt... -
Page 9: M6*30 Bolt
M6*30 Bolts Fasten the bolts Foot Avoid excessive tightening of bolts. STEP 4 1. Line up the screw holes with the feet and columns. 2. Fasten the bolts. ST4.8x16 Tapping Screw ST2.9x15 Tapping Screw The frame width is adjustable: 42-70 inch is suitable for desktop. STEP 5 1. -
Page 10: Cable Clip
STEP 6 1. Insert the handset and adjust to a suitable position of desktop edge to avoid any obstacles. 2. Tidy up all the power cables and fasten with cable clip. | ASSEMBLY INSTRUCTIONS... -
Page 11: Usage Instructions
V. USAGE INSTRUCTION MANUAL RESET It is necessary to be reset manually after the initial installation and power switched off. Press down key until the display shows "E-1" and "RES" alternately then release the key. Press down key again, the desktop will move slowly down and return until the display shows "70 (27.6") /60 (23.7")". - Page 12 SAVING POSITION Adjust the desktop to the desired height. Press "S" key, until the display will show "S --". Press "1" and the display will show as "S-1" and the desktop height Press "S" key, the first position is set successfully. Repeat for Button 2 and 3 height setting.
- Page 13 CHANGE THE DISPLAYED UNIT (CM / INCH) Press "S" key until the display show "S--" to enter the setup menu. Press up key until the display shows "UNT". Press "1", and the display will show alternately as "Unt" and the desktop current height value in "cm".
- Page 14 RESET TO FACTORY SETTING With this function, you can make the control unit to factory setting. Press "S" until the display shows "FAC". Press "S" again to confirm. CODE MEANING & TROUBLE SHOOTING CODE Information Operating Manual Resetting Refer to the progress of Manual Reset. Remove the load on desktop until it is less than 1000N (220 Overload lbs) before further operation...
-
Page 15: Exercise Guide
VI. EXERCISE GUIDE PLEASE NOTE: Before beginning any exercise program, consult your physician. This is important especially if you are over the age of 45 or individuals with pre-existing health problems. The pulse sensors are not medical devices. Various factors, including the user’s movement, may affect the accuracy of heart rate readings. - Page 16 COOL DOWN Finish each workout with a light jog or walk for at least 1 minute. Then complete 5 to 10 minutes of stretching to cool down. This will increase the flexibility of your muscles and will help prevent post- exercise problems.
-
Page 17: Warranty
Any claim against this warranty must be made through your original place of purchase. Proof of purchase is required before a warranty claim may be processed. If you have purchased this product from the Official Lifespan Fitness website, please visit https://lifespanfitness.com.au/warranty-form For support outside of warranty, if you wish to purchase replacement parts or request a repair or service, please visit https://lifespanfitness.com.au/warranty-form and fill in our Repair/Service... - Page 20 WWW.L IF ESPAN F ITNE S S . COM . A U...