Table of Contents
Related Manuals for Kendon Stand-Up TRIKE/SPYDER/SIDECAR Ride-Up SRL
Summary of Contents for Kendon Stand-Up TRIKE/SPYDER/SIDECAR Ride-Up SRL
- Page 1 KENDON TRIKE/SPYDER/SIDECAR RIDE-UP SRL* STAND-UP™ TRAILER *Suspension Reactive Loading OWNER’S MANUAL KENDON INDUSTRIES, LLC. 2990 E Miraloma Ave. Anaheim, CA 92806 USA Tel 714-630-7144 • Fax 714-630-7132 www.KendonUSA.com Rev. 171115...
-
Page 2: Table Of Contents
BEFORE loading. Kendon Industries, LLC is not responsible for damage to motorcycles or other vehicles caused by interference with trailer frame or components. -
Page 3: General Information
Trailer owner is responsible for complying with all the recommended procedures in this instruction manual. Use at your own risk. Kendon is not responsible for injury, liability, property damage and/or any consequential damage(s) caused by the misuse of this product. -
Page 4: Trailer Layout
Serious injury, death and/or property damage can result to operator and/or others through improper use of this product If you have any questions or need additional help or instructions, please see your local Kendon dealer or contact us directly at 714- 630-7144 or info@KendonUSA.com If you lost or need additional copies of any of the instructions manual referenced here, please visit our web site at www.KendonUSA.com... - Page 5 Loading ramps fold shut and slide onto the angled slide brackets below the rear section 3.2 Rear Section Your Kendon Stand-Up™ Trailer is designed to fold up and stand up to save storage space The Rear Section of your trailer folds onto the Front Section for...
- Page 6 3.6 Tie-Down Loops and Anchor Points Please refer to Section 8.0 for more information about proper tie- down procedures Tie-downs can be attached in several places on your Kendon trailer: o Front Raised Rail o On-Axle Tie-Down Loops – look for a bent steel loop...
- Page 7 Rear Section or vehicle components 3.8 Coupler and Hitch Ball Your Kendon trailer is equipped with a 2-inch* coupler designed to work with a standard 2-inch trailer hitch ball Make sure your tow vehicle’s hitch is equipped with a 2-inch* hitch...
-
Page 8: Assembly
4.0 ASSEMBLY If your Kendon trailer was delivered to you still packaged on a shipping crate, you will need to perform some easy assembly procedures. IF YOU DO NOT FEEL QUALIFIED TO PERFORM THESE ASSEMBLY PROCEDURES OR DO NOT FEEL COMFORTABLE PERFORMING... - Page 9 4.3 Install the Wheels Place the wheels onto the wheel hubs It may be necessary to remove extra crating or tip the trailer backward for full access to the wheel hubs (see the video for tips) Secure the wheels to the hubs using the lug nuts enclosed in the spare parts box It is not necessary to completely tighten the lug nuts yet 4.4 Remove the Trailer from the Crate...
- Page 10 Rear Section and vehicles. Please follow the included installation instructions. 4.9 Tighten Lug Nuts & Final Inspection Connect your Kendon trailer to your tow vehicle as indicated in Section 5.0 Using your lug wrench, torque the lug nuts to 60 ft-lbs. using a star-...
-
Page 11: Coupler, Safety Cables, And Lights
Rear section is latched closed (unless trailer is loaded) o There are no loose parts or tools on the trailer Your Kendon Stand-Up™ Trailer is ready for use. Register your trailer and install a license plate as required by the laws of your state. -
Page 12: Loading Ramps
Test both turn signals and brake lights prior to towing 6.0 LOADING RAMPS Your Kendon Ride-Up SRL Trike/Spyder/Sidecar Stand-Up™ Trailer is equipped with a two-piece, full-width, slide-out loading ramp designed to let you easily and safely load your vehicles onto the trailer. - Page 13 6.2 Loading Ramp Configuration The loading ramp sections will be marked left and right when you receive your trailer from Kendon; please be sure to understand which section is which before removing the marking tag The left loading ramp section will feature the small 12” fold-out side...
-
Page 14: Loading And Unloading
7.0 LOADING AND UNLOADING When properly performed, the loading/unloading procedures should be very safe and easy on your Kendon Ride-Up SRL Trike/Spyder/ Sidecar Trailer. Loading and unloading a vehicle requires certain skills and techniques. Kendon recommends using two spotters while practicing the loading and unloading technique with your bike. - Page 15 Your license plate will swing open to eliminate clearance issues Align your vehicle so the vehicle’s centerline is near the centerline of your Kendon trailer Gently and slowly ride or push your vehicle onto the trailer Guide the vehicle onto the trailer between the Raised Front Rail on...
-
Page 16: Tie-Down Procedure
Close the Swing Out License Plate Holder, secure with retaining pin 8.0 TIE-DOWN PROCEDURE KENDON USES A FOUR (4) POINT TIE-DOWN SYSTEM. IT IS NOT SAFE TO TOW YOUR MOTORCYCLE WITHOUT TYING IT DOWN OR BY ONLY USING THE FRONT OR REAR TIE-DOWNS. KENDON RECOMMENDS USING TOP-QUALITY RATCHET-STYLE TIE- DOWNS TO APPLY ADEQUATE PRESSURE WHEN TYING DOWN. -
Page 17: Trailer Storage
Suggested tie-down configuration for a trike-style vehicle: Suggested tie-down configuration for Can-Am Spyder or similar vehicle: 9.0 TRAILER STORAGE Your Kendon Stand-Up™ Trailer is designed to fold up and stand up to minimize storage space. Kendon recommends using help for at least the -17-... - Page 18 first few times you stand up and lower your trailer to be sure you do not injure yourself or cause property damage. The procedures listed below are recommendations only. Practice and technique refinement will result in the easiest operation of your trailer. 9.1 Standing your trailer up for storage Before folding the Rear Section closed, open the Swing Out License Plate Holder by unscrewing the retaining pin on the top right...
-
Page 19: Hazards And Maintenance
Improper tongue weight: Your Kendon trailer requires 10%-15% of total GVWR on the tongue for proper handling in tow. Please ensure you have adequate tongue weight prior to towing. Contact Kendon at 714.630.7144 if you need assistance measuring tongue weight. If your Kendon trailer begins to sway side to side while towing, immediately. -
Page 20: Parts And Accessories
Bearings and seals: https://www.kendonusa.com/kendon-technical- insight-series-wheel-bearings-seals-lubrication/ 11.0 PARTS AND ACCESSORIES Kendon offers a variety of replacement parts and accessories for your new trailer. Please visit www.kendonusa.com or call 714.630.7144 to order any one of these great accessories. And check back often for the latest ways to make your Kendon trailer your own.