Related Manuals for Ricoh PJ Interactive Kit Type 3
Summary of Contents for Ricoh PJ Interactive Kit Type 3
- Page 1 Operating Before Using RICOH PJ Interactive Kit Type3 Instructions Troubleshooting Appendix For safe and correct use, be sure to read Safety Information before using the machine.
-
Page 3: Table Of Contents
How to Read This Manual..........................3 Symbols................................3 Disclaimer................................3 Notes................................3 1. Before Using RICOH PJ Interactive Kit Type3 RICOH PJ Interactive Kit Type3 Overview....................... 5 Checking the Contents of the Product....................... 7 Preparations for Using the Interactive Function....................9 Attaching the Interactive Sensor to the Projector..................10 Installing the Supplied Software on a Computer.................. -
Page 4: Introduction
Introduction This manual contains detailed instructions and notes on the operation and use of this product. For your safety and benefit, read this manual carefully before using the product. Keep this manual in a handy place for quick reference. -
Page 5: How To Read This Manual
How to Read This Manual Symbols This manual uses the following symbols: Indicates points to pay attention to when using functions. This symbol indicates points that may result in the product or service becoming unusable or result in the loss of data if the instructions are not obeyed. Be sure to read these explanations. -
Page 7: Before Using Ricoh Pj Interactive Kit Type3
1. Before Using RICOH PJ Interactive Kit Type3 This chapter provides an overview of RICOH PJ Interactive Kit Type3 and describes its basic operations. RICOH PJ Interactive Kit Type3 Overview With this product, you can operate a computer screen projected on the screen. With "RICOH Interactive Whiteboard Lt", the software that comes with this product, you can write information and perform... - Page 8 1. Before Using RICOH PJ Interactive Kit Type3 Visual overview of using the product with the RICOH PJ WUC4650/WXC4660 series Y0E5IX0062...
-
Page 9: Checking The Contents Of The Product
22 "Replacing the Pen Nib". Y0E5IX0073 Cable clip for the RICOH PJ WX4153 Attach this to the RICOH PJ WX4153 series and secure series × 2 the USB cable. For details about how to attach the cable clip, see page 11 "Attaching the interactive sensor to the... - Page 10 1. Before Using RICOH PJ Interactive Kit Type3 Accessories Usage Attachment for the RICOH PJ WUC4650/ Used when attaching the interactive sensor to the WXC4660 series RICOH PJ WUC4650/WXC4660 series. For details about how to attach the interactive sensor to the RICOH PJ WUC4650/WXC4660 series, see page 13 "Attaching the interactive sensor to the...
-
Page 11: Preparations For Using The Interactive Function
The interactive function allows you to operate a computer connected to the projector directly on the projection screen. Writing and drawing on a projected screen You can also write and draw on a projected screen using the included software "RICOH Interactive Whiteboard Lt". To use the interactive function, the following settings are required:... -
Page 12: Attaching The Interactive Sensor To The Projector
1. Before Using RICOH PJ Interactive Kit Type3 To use the interactive function with the RICOH PJ WUC4650/WXC4660 series Y0E5IX0063 Step Setting Contents Reference Attach the interactive sensor to the projector. See page 10 "Attaching the Interactive Sensor to the Projector". - Page 13 Preparations for Using the Interactive Function Attaching the interactive sensor to the RICOH PJ WX4153 series Remove the top cover of the projector. Loosen the screws by using the hexagon wrench, and then hold the screws and lift them upward together.
- Page 14 1. Before Using RICOH PJ Interactive Kit Type3 Hook the cords onto the protrusion. Y0E5IX0031 Screw in the interactive sensor. Fasten the two locations by using the hexagon wrench. Y0E5IX0030 Attach the cable clips to the projector. Attach the cable clips to the top and bottom of the intake vents on the right side of the projector, avoiding the intake vents.
- Page 15 Preparations for Using the Interactive Function Attaching the interactive sensor to the RICOH PJ WUC4650/WXC4660 series • Highly adhesive double-sided tape is used to secure the attachment. • Be careful not to touch the adhesive surface of the tape. • Be careful of the position and orientation when attaching the attachment.
- Page 16 1. Before Using RICOH PJ Interactive Kit Type3 1. Attachment reference 1 2. Attachment reference 2 Gently wipe away any dirt from where the attachment is to be secured. Y0E5IX0087 See the orientation of the attachment and the references for securing it.
-
Page 17: Installing The Supplied Software On A Computer
Y0E5IX0036 Installing the Supplied Software on a Computer To write and draw on a projection screen, install the RICOH PJ Interactive Setup Software and RICOH Interactive Whiteboard Lt on a computer. For details about how to use the RICOH PJ Interactive Setup Software, see page 17 "Aligning Pen Recognition Positions". -
Page 18: Connecting The Projector And A Computer
1. Before Using RICOH PJ Interactive Kit Type3 Connecting the Projector and a Computer This section explains how to connect the projector and a computer. Connect the computer to the projector using RGB cables or an HDMI cable. For the connection procedure, see the operating instructions provided with the projector. -
Page 19: Aligning Pen Recognition Positions
Project the computer screen on the projector screen. For the projecting procedure, see the operating instructions provided with the projector. Start the RICOH PJ Interactive Setup Software. When the images are projected in "Rear" or "Ceiling" mode, select the appropriate projection mode under "Options"... - Page 20 1. Before Using RICOH PJ Interactive Kit Type3 Adjust the angle of the sensor so the projected image fits within the blue frame. Adjust brightness of the sensor when the projected image is blurred. Adjust the camera angle by using the hexagon wrench to make the bottom of the projected image as close to the bottom of the blue frame as possible.
- Page 21 Whiteboard Lt will start. Then, you can directly operate the computer display on the projected screen with the interactive pen. • You cannot operate the computer display with the interactive pen when RICOH PJ Interactive Setup Software is still running.
-
Page 22: Using The Interactive Pen
You may also touch the pen nib twice on the same position of the screen, much like the double-click of a mouse. • You cannot operate the computer display with the interactive pen when the RICOH PJ Interactive Setup Software is still running. Upon the completion of aligning pen recognition positions, click [Start IWB Lt] under "STEP 3 Start Handwriting Software"... -
Page 23: Installing Batteries Into The Interactive Pen
Using the Interactive Pen Installing Batteries into the Interactive Pen • For safe operation, follow the warnings below regarding the batteries. If you use the batteries incorrectly, it may result in fire or injury due to batteries leaking or exploding. •... -
Page 24: Replacing The Pen Nib
1. Before Using RICOH PJ Interactive Kit Type3 Unscrew the battery cover. Y0E5IX0040 Install the batteries. Check that the batteries have been installed in the right direction. Y0E5IX0041 Re-install the battery cover. Y0E5IX0042 Replacing the Pen Nib Replace the pen nib whenever it becomes worn out and shorter. - Page 25 Using the Interactive Pen Remove the pen nib. Y0E5IX0085 Attach a new pen nib. Push it in until it clicks. Y0E5IX0086...
- Page 26 1. Before Using RICOH PJ Interactive Kit Type3...
-
Page 27: Troubleshooting
This chapter describes what to do when a message is displayed or when the product cannot be operated as wanted. What to Do When a Message Is Displayed The following table lists the main messages and their recommended actions. RICOH PJ Interactive Setup Software Message Message Causes Solutions Cannot use the sensor. - Page 28 It is already running. You have attempted to start the You cannot start another RICOH PJ Interactive Setup instance of the RICOH PJ Software when it is already Interactive Setup Software when running. one instance is already running. Use the RICOH PJ Interactive Setup Software instance that is already running.
-
Page 29: When The Projected Screen Cannot Be Operated
RICOH PJ Interactive Setup interactive pen when the RICOH PJ Interactive Setup Software is running. Software is running. Close the RICOH PJ Interactive Setup Software instance when it is still running until after completing the alignment of pen recognition positions. For details about closing the RICOH PJ Interactive Setup Software, see page 17 "Aligning Pen Recognition Positions". - Page 30 Check to see whether the If it is not correct, align the pen recognition positions again pen recognition positions using the RICOH PJ Interactive Setup Software. For details are correctly aligned. about aligning pen recognition positions, see page 17 "Aligning Pen Recognition Positions".
-
Page 31: When The Projected Screen Cannot Be Operated As Wanted
When the Projected Screen Cannot Be Operated As Wanted When the Projected Screen Cannot Be Operated As Wanted This section explains what to do when the projected screen cannot be operated as wanted. Problem Solutions Cannot be operated with the Use the interactive pen so as not to block the area between the interactive pen. - Page 32 2. Troubleshooting...
-
Page 33: Appendix
3. Appendix Trademarks Intel and Core are trademarks of Intel Corporation in the U.S. and/or other countries. Microsoft, Windows, Windows Vista, and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. The proper names of the Windows operating systems are as follows: •... - Page 34 MEMO Y0E5-7521...
- Page 35 © 2020 Ricoh Co., Ltd.
- Page 36 Y0E5-7521...