Raider RD-EBV04 User Manual page 12

12 www.raider.bg
Keep extension cords away from moving
hazardous parts to avoid damages to the cords
which can lead to contact with live parts.
Use a separate electrical circuit for your tools.
Before connecting the motor to the power line,
make sure the switch is in the OFF position
and the electric current is rated the same as
the current stamped on the motor nameplate.
Running at a lower voltage will damage the
motor.
3.ASSEMBLY AND ADJUSTMENTS
This blower only need to assembly collection
bag when you take out from packing box .
Reference Fig2.
1. Put the hook of collection bag on the down
tube (like arrow 1).
2. Put the frame on the housing (like arrow 2).
3. Stretch the tube , keep both tube in longest
state .
4. Tight the knob .
Reference Fig3.
5. Adjust front handle , make it in suitable
situation.
WARNING: IF ANY PART IS MISSING OR
DAMAGED, DO NOT PLUG IN THE MACHINE
UNTIL YOU HAVE REPLACED THE MISSING
OR DAMAGED PART.
4.OPERATION
WARNING: IF THE CORD HAS BEEN
DAMAGED, HAVE IT REPLACED BEFORE
USING THE BLOWER.
TO OPERATE THE BLOWER:
1. Take the belt on your shoulder.
2. Grab the big handle with your right hand and
grip the small handle with your left hand as Fig.1
illustration.
3. Turn the knob to "mark for vac." Position
when you need the vac. Function. Turn the
knob to "mark for blow" position when you need
blowing function.
Please refer Fig.3 .
4.Connect the plug to main power supply, and
depress the on-off switch.
5.Wheels can roll on the ground to let user easy
push the machine forward and back.
6.When the bag is full, zip the bag to open it
directly and discharge the leaves which have
been shredded or uninstall the bag from the
machine to discharge the leaves.
4. When using teeth to rake the leaf, adjust teeth
in correct situation .(like Fig4)
5. When something block the fan , unscrew the
knob and open the transparent window ,can
easily clean fan .
5.MAINTENANCE
WARNING: ALWAYS TURN OFF THE
BLOWER&VAC. AND UNPLUG THE POWER
CORD FROM THE OUTLET BEFORE
MAINTAINING THE BLOWER&VAC.
GENERAL MAITENANCE
Keep your blower&vac. clean and in good
repair for maximum performance and machine
longevity. Before each use, inspect the
blower&vac., switch and cord for damage.
Check for damaged, missing or worn parts.
Check for any conditions that may affect the
operation. If abnormal vibration or noise occurs,
turn off the tool immediately and have the
problem corrected before further use. Do not
use the blower&vac. until it is properly repaired
or replaced.
Always replace a damaged switch, cord or have
it repaired by the manufacturer or its service
agent or a qualified delectrician before using it ,
which is in order to avoid a hazard.
Cleaning
Use only mild soap and a damp cloth to clean
your tools. Certain cleaning agents and solvents
are harmful to plastic and other insulated
parts. DO NOT use brake fluids, gasoline,
penetrating oils, turpentine, lacquer thinner,
paint thinner, chlorinated cleaning solvents,
ammonia, or household cleaning detergents
containing ammonia, The contain chemicals that
can weaken or destroy plastic and will cause
damage to the blower&vac.
WARNING:TO AVOID FIRE OR TOXIC
REACTION, DO NOT USE GASOLINE,
NAPHTHA, ACETONE, LACQUER THINNER,
OR SIMILAR HIGHLY VOLATILE SOLVENTS
TO CLEAN THE TOOL.
WARNING:TO AVOID ANY INJURY, ELECTRIC
SHOCK, OR DAMAGE TO THE TOOL NEVER
IMMERSE THE TOOL IN A LIQUID OR ALLOW
A LIQUID TO FLOW INSIDE THE TOOL.
Lubrication
All the bearings in this tool are lubricated with
a sufficient amount of lubricant for the life of
the unit under normal operating conditions. No
further lubrication is required.
6. Replacing the power cable
If the power cable for this equipment is
damaged, it must be replaced by the
manufacturer or its aftersales service or similarly
trained personnel to avoid danger.
7. Environmental protection.
In view of environmental protection