Calling Up Information About The System - Bosch Compress 7001i AW User Manual

Menu item Description
Warning sound If a buzzer has been installed a warning sound is
blocked emitted as soon as an alarm occurs. The warning
sound can be suppressed at a settable time interval.
Reduced DHW Setting for the reduced DHW mode. If [Yes] is set,
temp. the DHW temperature is reduced if there are a
compressor fault. The function is used to reduce the
use of the auxiliary heater.
DHW temp. Correction of the DHW temperature displayed by
correction the user interface by up to ± 10 °C.
Time correction Time correction of the internal clock of the user
interface in s/week.
Standard display Settings for the display of additional temperatures in
the standard display.
Internet Reset the personal password for the Internet
password connection (only available if a communication
module is installed). The next time you log in, e.g.
using an App, you will automatically be prompted to
assign a new password.
Internet Make settings for the Internet connection (only
available if a communication module is installed).
• [Establish connection]
– [Pairing-Status]
– [Activate hotspot]
– [Activate WPS]
• [Terminate connection]
– [Connected network]
– [Terminate connection]
Low-noise If activated the heat pump will run in reduced sound
operation operation during the set time period.
• [Low-noise operation of]: set the start time for
the low noise operation.
• [Low-noise operation until]: set the stop time for
the low noise operation.
• [Min. outside temp.]: Below this outdoor
temperature the heat pump switches over to
normal operation.
Reset Reset all settings to the values set at commissioning.
Table 19 General Settings
3.4

Calling up information about the system

The current system values and the active operating conditions can be
displayed easily via the info menu. No changes can be made in this menu.
To open the info menu:
▶ Press the info key in the standard display.
Menu: Sum./winter changeover
Menu item Description
Heating/cooling Currently valid operating mode in the selected
mode heating circuit.
Set room temp. The desired room temperature that is currently valid
in the selected heating circuit:
• In automatic mode, this can change several times
a day, if necessary.
• In normal operation, it is always constant.
Measured room Currently measured room temperature in the
temp. selected heating circuit
Measured flow Currently measured flow temperature in the
temp. selected heating circuit
Table 20 Information about the heating
Compress 7001i/7400i AW AWE – 6721835320 (2021/09)
Menu: DHW
Menu item Description
Set temp. Desired DHW temperature.
Measured temp. Currently measured DHW temperature.
Table 21 Information about DHW
Menu: Ventilation
Menu item Description
Op. mode Currently selected operating mode and ventilation level
Outside temperature Display of Outside temperature
Supply air temp. Display of supply air temperature
Ex.air temp. Display of extract air temperature
Exhaust air temp. Display of exhaust air temperature
Reheat supp.air temp. Display of supply air temperature from the re-heater
Ex.air humid. Display of exhaust air humidity
Ex.air quality Display of exhaust air quality
Humidity remote ctrl Display of humidity in the installation room of the
remote control
Amb. air humid. Display of ambient air humidity
Amb. air quality Display of ambient air quality
Bypass Display of bypass-settings
Rem. filter elapsed Display of duration in days until the next filter change
time
Table 22 Information about the ventilation unit
Menu: Pool
Menu item Description
Set pool Desired pool temperature.
temperature
Current pool Currently measured pool temperature.
temperature
Table 23 Information about pool
Menu: Operating data
Menu item Description
Control Hours run by the control since the heat pump was
operating hours commissioned or since the last reset.
Aux. heater Output of the electric booster heater since
energy cons. commissioning or since the last reset.
Op. hours for Hours run by the compressor in heating mode since
comp. heat. commissioning or since the last reset.
Op. hours for Hours run by the compressor in cooling mode since
comp. cool. commissioning or since the last reset.
Op. hours for Hours run by the compressor in DHW operation
comp. DHW since commissioning or since the last reset.
Op. hours for Hours run by the compressor in pool operation since
comp. pool commissioning or since the last reset.
Number of Number of compressor starts in heating mode since
heating starts commissioning or since the last reset.
Number of Number of compressor starts in cooling mode since
cooling starts commissioning or since the last reset.
Number of DHW Number of compressor starts in DHW operation
starts since commissioning or since the last reset.
Number of pool Number of compressor starts in pool operation since
starts commissioning or since the last reset.
Table 24 Operation data
Operation
17