Solas SEVENTY2 LGS-72 Installation Manual
Direct vent log set kit for 72n-ssl, 72p-ssr, 72n-st, 72p-ssl, 72p-ssr, 72p-st
Hide thumbs
Also See for SEVENTY2 LGS-72:
- Installation manual (9 pages) ,
- Installation manual (10 pages)
Table of Contents
Advertisement
Quick Links
SEVENTY2
DIRECT VENT LOG SET KIT
PART #: LGS-72
INSTALLATION MANUAL
ONLY FOR USE ON SÓLAS MODELS: 72N-SSL, 72P-SSR, 72N-ST, 72P-SSL, 72P-SSR, 72P-ST
WARNING
This log set kit shall be installed by a qualified service agency in accordance with
the manufacturer's instructions and all applicable codes and requirements of the
Authority Having Jurisdiction. If the information in these instructions is not
followed exactly, a fire, explosion or production of carbon monoxide may result
causing property damage, personal injury or loss of life. The qualified service
agency is responsible for the proper installation of this kit. The installation is not
proper and complete until the operation of the converted appliance is checked as
specified in the manufacturer's instructions supplied with the kit.
NOT FOR USE WITH VENT FREE OR OUTDOOR FIREPLACES
0
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Solas SEVENTY2 LGS-72
Summary of Contents for Solas SEVENTY2 LGS-72
- Page 1 SEVENTY2 DIRECT VENT LOG SET KIT PART #: LGS-72 INSTALLATION MANUAL ONLY FOR USE ON SÓLAS MODELS: 72N-SSL, 72P-SSR, 72N-ST, 72P-SSL, 72P-SSR, 72P-ST WARNING This log set kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the Authority Having Jurisdiction.
- Page 2 LOG SET INSTALLATION Kit Contents: • 2lb 0oz Lava Rock • (5) Ceramic Logs • (6) Ceramic Rocks • Metal Logset burner set Figure 01 - Burner Support locations Step #1 Your fireplace will have shipped from the factory with the Glass Media burners in place, before installing the logset burners, we need to remove the glass burners.
- Page 3 LOG SET INSTALLATION Step #3 To remove the right burner, remove the 6 sheet metal screws securing the right burner, these screws are identified by the 6 arrows below. Once all hardware has been removed, slide the burner to the right and lift the burner out of the fireplace. Figure 04 Figure 05 Step #5...
- Page 4 LOG SET INSTALLATION Step #8 FIGURE 11 Install the 3-rock cluster on the 2 pins located at the far left of the firebox as shown in figure 8. Step #9 FIGURE 12 Install the right-hand birch log by placing the left side of the log on the 3-rock cluster installed in step #10.
- Page 5 LOG SET INSTALLATION Step #13 FIGURE 14 Between the rock installed during step #12 and the center birch log are 4 pins located in close proximity to each other. Place the first of the 2 individual rocks on the left set of pins. Look for a gap between the front of the rock and the leading edge of the burner, if the rock overhangs the front of the burner the incorrect...
- Page 6 LOG SET INSTALLATION Step #16 FIGURE 17 Evenly distribute the included 1lb and 3oz of lava rock on the exposed burner top. Cover the burner top completely but do not compress or “pack” the lava rock tightly. Pay special attention to tight and hard to reach areas when placing the media on the burner.
- Page 7 LOG SET INSTALLATION Installation is now complete, refer to the FORTY6 owner’s manual for instructions on final assembly and lighting of the appliance.
Need help?
Do you have a question about the SEVENTY2 LGS-72 and is the answer not in the manual?
Questions and answers