Advertisement
Quick Links
1. IntroductIon...............................................................3
2. MaIn parts and controls.......................................4
3. How to use: MaIn steps.............................................5
4. How to use: step by step............................................6
Step 1: Mounting the book block.....................................6
Step 2: trimming.............................................................14
Step 3: Mounting the cover............................................15
5. copyrIgHt, tradeMarks and warranty.............18
Advertisement
Related Manuals for Fastbind Pureva XT
Summary of Contents for Fastbind Pureva XT
- Page 1 1. IntroductIon...............3 2. MaIn parts and controls........4 3. How to use: MaIn steps..........5 4. How to use: step by step..........6 Step 1: Mounting the book block........6 Step 2: trimming.............14 Step 3: Mounting the cover..........15 5. copyrIgHt, tradeMarks and warranty.....18...
- Page 3 * output rate depends on operator, selected cover and glue type ** depending on material properties. product information as of July 2014 and is subject to change without prior notice. DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
- Page 4 Hex key 4 mm soft cover nipping tool back Hex key 2,5 mm (for nipping bar adjustment) hard cover nipping tool front power cord hard cover nipping tool back DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
- Page 5 3d turn table front plate 3e Fastening holes for paper guide 4 temperature control panel 4a Indicator lights 4b temperature selection button 5 Front heat shield DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
-
Page 6: Machine Installation
• the storage locker has two compartments and it is intended only for storing glue head grippers. o warnIng! ▪ The storage locker is not permanently fixed to the machine. ▪ remove the locker before moving the machine. DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014... - Page 7 • drain the glue cartridge by applying glue using a chip board (gray board) or other thick paper substrate. DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
- Page 8 • when the auto-off has turned the heaters off, the red standby – light is lit. • when the temperature selection button is pressed, the machine starts heating again. DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
- Page 9 • the bypass vent is opened to improve fume extraction from the glue cartridge when adding pur glue or checking glue level. For details, please, please see glue cartridge Handling -section DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
- Page 10 ▪ always keep the gripper in upright position. ▪ store the gripper in the locker. the locker must be properly installed (see the locker installation instructions) DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
- Page 11 - the externally connected fume extractor is on and operating - and the glue cartridge is securely connected in the heating dock, positioned under the bypass vent, which must be in the open position. DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
- Page 12 ▪ keep the gripper always in upright position. ▪ store the gripper in the locker, making sure it is properly installed (see locker installation instructions). • Install new cartridge as in section 7.3 DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
- Page 13 • Move the heating dock back to home position • replace thermal casing covers • close the vent • wait a minimum 10 minutes before resuming normal operations DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
-
Page 14: Heat Shield
DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014... - Page 15 DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
- Page 16 • when closing the clamp, press the support rod down to hold the table in position when locking. DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
- Page 17 • side gluing for hard cover books ▪ After gluing, flip the spine stick on the glued book spine to get a professional finish. DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
- Page 18 • leave a small amount of eVa glue in the cartridge. DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
- Page 19 Tel. +358 9 562 6022 Fax: +358 9 562 6215 Tel. +358 9 562 6022 Fax: +358 9 562 6215 Espoo, 25.6.2014 _______________________ Helsinki, 2006-01-05 Lauri Huotari, Managing Director DRAFT Fastbind PUREVa Xt UsER manUal | v 1.0 | © maping Co 2014...
- Page 20 X, y, Z are trademarks of Maping co. Fastbind pureva Xt is invention tradeMarks and patents of the Maping co (patent pending).
Need help?
Do you have a question about the Pureva XT and is the answer not in the manual?
Questions and answers