3M Liqui-Cel EXF-10x28 Series Assembly And Disassembly Instructions

3M Liqui-Cel EXF-10x28 Series Assembly And Disassembly Instructions

Membrane contactor

Advertisement

Quick Links

3M
Liqui-Cel
EXF-10x28
Series Membrane Contactor
Assembly and Disassembly Instructions
3M.com/Liqui-Cel

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Liqui-Cel EXF-10x28 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for 3M Liqui-Cel EXF-10x28 Series

  • Page 1 Liqui-Cel EXF-10x28 ™ ™ Series Membrane Contactor Assembly and Disassembly Instructions 3M.com/Liqui-Cel...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Safety and Warning Assembly Parts III. Part Orientation IV. Assembly Tools End Cap Removal VI. Cartridge Insertion VII. End Cap Preparation / Installation Manual Insertion Vacuum Insertion IX. Center Seal Tightening Pressure Test...
  • Page 3: Safety And Warning

    • The membrane contactor(s) should not be stored where they are exposed to Use in any other application may not have been evaluated by 3M and may direct sunlight. Membrane contactors should always be stored in sealed bags or shrink wrap material and in the original box or other opaque box.
  • Page 4: Assembly Parts

    ASSEMBLY PARTS O-rings (4) Inner O-ring To seal the cartridge into the housing, this 7.5 mm O-ring is the shellside or liquid side O-ring. Outer O-ring To seal the cartridge into the end cap, this 6.9 mm O-ring is the lumenside or gas side O-ring. Lock ring (2) An elastomeric ring used to position the inner shellside O-ring.
  • Page 5: Assembly Tools

    Assembly Clips Dark machined parts that slide over the Assembly Rods. Assembly Chips The equipment illustrated above is required for the assembly or disassembly of a 3M Liqui-Cel EXF-10x28 Series ™ ™ Membrane Contactor that will be assembled in a 316L SS Housing.
  • Page 6: End Cap Removal

    END CAP REMOVAL WARNING To reduce the risks associated with crush or impact related injuries: • Always ensure the membrane contactor is properly secured. Be sure the membrane contactor cannot tip, roll, fall, slide or make any movement that may cause injury or damage to other system components.
  • Page 7: Cartridge Insertion

    WARNING To reduce the risks associated with explosion: • Only use replacement parts supplied by 3M for this product. To reduce the risks associated with crush or impact related injuries: • Always ensure the membrane contactor is properly secured. Be sure the membrane contactor cannot tip, roll, fall, slide or make any movement that may cause injury or damage to other system components.
  • Page 8 • (E) Use the T-Handle insertion tool to press in the remaining O-ring sections. When inserting the O-rings, it is best to always divide each section of un-inserted O-ring in half and press in the middle section. See the photograph to the right, for an example. •...
  • Page 9: End Cap Preparation/Installation

    To reduce the risks associated with explosion: • Only use replacement parts supplied by 3M for this product. To reduce the risks associated with crush or impact related injuries: • Always ensure the membrane contactor is properly secured. Be sure the membrane...
  • Page 10: Vacuum Insertion

    • (D) It is necessary to tighten in a pattern similar to the one shown on this picture. This will ensure that the end cap is inserted evenly. • While the end cap is pulled tight against the housing, place the V-Band clamps on the ridges of housing and the end caps and tighten the clamps.
  • Page 11: Center Seal Tightening

    • (G) Turn the vacuum pump on. Press the end caps against the O-rings. • (H) While the end cap is pulled tight against the housing, place the V-Band clamp on the ridge of the housing and the end cap and tighten the clamp.
  • Page 12 3M’s option, replacement of the 3M product or refund of the purchase price. Limitation of Liability: Except for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss or damage arising from or related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or business opportunity), regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability.

Table of Contents