Table of Contents
Advertisement
Referencing Setup
Referencing Setup
Referencing Setup
Referencing Setup
Referencing Setup
The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection
The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection
The connectors on the Test Jumper and loopback should be cleaned to appropriate standards. Use
The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection
REFERENCING SETUP
scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP 460 and DLS 350.
The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection
scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP 460 and DLS 355.
an inspection scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP
scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP 460 and DLS 355.
The RP 460 should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm
The connectors on the Test Jumper should be cleaned to appropriate standards. Use an inspection scope to
scope to verify fiber cleanliness. Plug the connectors on the Test Jumper into the RP 460 and DLS 350.
The RP 460 should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm
460 and DLS 350. Plug the loopback adapter on to the paired LC side of the Test Jumper. The RP 460
The RP 460 should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm
button once to put it into the dBm mode.
verify fiber cleanliness. Plug the connectors on the Test Jumper into the OPM1 and LSMM. The OPM1 should
The RP 460 should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm
button once to put it into the dBm mode.
button once to put it into the dBm mode.
should be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm button
be in the dBm measurement mode. If it is not in the dBm mode, press the dB/dBm button once to put it into the
button once to put it into the dBm mode.
once to put it into the dBm mode.
dBm mode.
Test Jumper
Setting Reference
Setting Reference
Setting Reference
Setting Reference
SETTING REFERENCE
Setting Reference
The DLS 350 output power is calibrated to -22dBm. If the RP 460 screen displays between -22.00dBm
The DLS 355 output power is calibrated to -5dBm. If the RP 460 screen displays between -5.00dBm
The DLS 355 output power is calibrated to -5dBm. If the RP 460 screen displays between -5.00dBm
The DLS 350 output power is calibrated to -22dBm. If the RP 460 screen displays between -22.00dBm
The LSMM output power is calibrated to -22dBm. If the OPM1 screen displays between -22.00dBm and
and -25.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the
The DLS 350 output power is calibrated to -22dBm. If the RP 460 screen displays between -22.00dBm
and -7.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the
and -25.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the
and -7.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the
-25.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the dB/dBm button. The
dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the
and -25.00dBm, press and HOLD the dB/dBm button for 5 seconds. After 5 seconds, release the
dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the
dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the
dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the
OPM1 screen will display 0.00dB, with some minor variation. DO NOT switch the OPM1 back to the dBm mode.
RP 460 back to the dBm mode.
dB/dBm button. The RP 460 screen will display 0.00dB, with some minor variation. DO NOT switch the
RP 460 back to the dBm mode.
RP 460 back to the dBm mode.
RP 460 back to the dBm mode.
RP 460 back to the dBm mode.
Between -22 and -25dBm
Between -5.00 and -7.00dBm
Between -5.00 and -7.00dBm
Between -22 and -25dBm
Between -22 and -25dBm
Between -22 and -25dBm
Loss Test
Loss Test
Loss Test
Loss Test
LOSS TEST
Loss Test
The Test Jumper MUST remain attached to the DLS 350. Do not remove the Test Jumper from the
The Test Jumper MUST remain attached to the DLS 355. Do not remove the Test Jumper from the
The paired Test Jumper MUST remain attached to the DLS 350 and RP 460. Do not remove the Test
The Test Jumper MUST remain attached to the DLS 355. Do not remove the Test Jumper from the
optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be cleaned to
The Test Jumper MUST remain attached to the LSMM. Do not remove the Test Jumper from the optical link.
The Test Jumper MUST remain attached to the DLS 350. Do not remove the Test Jumper from the
optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be cleaned to
optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be cleaned to
Jumper from the optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be
The connectors on the Test Jumper and the fiber-under-test should be cleaned to appropriate standards. Use
appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the Test Jumper
optical link. The connectors on the Test Jumper and the Fiber-Under-Test should be cleaned to
appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the Test Jumper
appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the Test Jumper
cleaned to appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the clipped
an inspection scope to verify fiber cleanliness. Plug the Test Jumper into one end of the fiber-under-test using
into one end of the Fiber-Under-Test using a bulkhead adapter as shown. Plug the other end of the
appropriate standards. Use an inspection scope to verify fiber cleanliness. Plug the Test Jumper
into one end of the Fiber-Under-Test using a bulkhead adapter as shown. Plug the other end of the
into one end of the Fiber-Under-Test using a bulkhead adapter as shown. Plug the other end of the
LC end of the Test Jumper into one end of the Fiber-Under-Test using the bulkhead as shown. Plug
a bulkhead adapter as shown. Plug the other end of the fiber-under-test into the LC adapter on the OPM1. The
Fiber-Under-Test into the LC adapter on the RP 460. The Insertion Loss of the Fiber-Under-Test will be
into one end of the Fiber-Under-Test using a bulkhead adapter as shown. Plug the other end of the
Fiber-Under-Test into the LC adapter on the RP 460. The Insertion Loss of the Fiber-Under-Test will be
Fiber-Under-Test into the LC adapter on the RP 460. The Insertion Loss of the Fiber-Under-Test will be
the loopback on to the other end of the Fiber-Under-Test. The Insertion Loss of the Fiber-Under-Test
Insertion Loss of the fiber-under-test will be shown on the OPM1 screen.
shown on the RP 460 screen.
Fiber-Under-Test into the LC adapter on the RP 460. The Insertion Loss of the Fiber-Under-Test will be
shown on the RP 460 screen.
shown on the RP 460 screen.
will be shown on the RP 460 screen.
shown on the RP 460 screen.
Test
Jumper
DMT
DMT
DMT
DMT
3330 Earhart Drive, Suite 208
DMT
Hold for 5 seconds
Hold for 5 seconds
Hold for 5 seconds
Hold for 5 seconds
Hold for 5 seconds
Hold for 5 seconds
Fiber-Under-Test
|
|
Carrollton, TX 75006
Office: 972.556.0916
Reference is set
Reference is set
Reference is set
Reference is set
Reference is set
Reference is set
M-UM038-01 RP 460 Reference and Test
M-UM038-01 RP 460 Reference and Test
M-UM038-01 RP 460 Reference and Test
|
M-UM038-01 RP 460 Reference and Test
Fax: 972.910.8384
M-UM038-01 RP 460 Reference and Test
OPM1
Page 10
Page 4
Page 4
Page 12
PAGE 9
Page 10
Advertisement
Table of Contents
