Advertisement
Quick Links
ALGO 5 Installation and Assembly Instructions
1. Preparation
Examine the shipping containers carefully upon receipt. If any of the boxex are damaged or
the packing materials show signs of stress, notify the carrier and keep the shipping materials
for the carrier's inspection.
The ALGO 5 includes these items packaged and shipped separately in 4 boxes::
•
Cart base with Isolation Transformer
•
Cart column (with cable guide protective covers included but not installed)
•
Panel PC with Panel PC power supply
•
Accessories box: keyboard, DSP Box, Preamp 5, ATA 5 cable, Sample Pack, label
printer, and accessories pack: Equipment Check Kit, USB Cable, two PCA 5 cables,
CD, power cord, and documentation package
•
Optional items packaged separately: Barcode scanner, LAN Isolator, and page
printer.
Note: Save shipping boxes and packing foam in the event that the screening module
must be returned to the manufacturer.
Required Tools
•
T-handle allen wrench, 3/16" (supplied, in Cart Base packaging)
•
90 degree allen wrench, 1/8" and 5/32" (supplied, in Cart Column packaging)
•
7/16" standard wrench or adjustable crescent wrench (not supplied)
•
Phillips screwdriver (not supplied)
Hardware Supplied
•
Socket head screws (#1/4-20 x 1 1/4") with lock washers & flat washers (4, in Cart
Base packaging)
•
KEP nuts (#1/4-20) – (2, in Cart Base packaging)
•
Socket head cap screws (#10-32 x 1/2" SHCS) - (4, in Cart Column packaging)
•
Pan head screws (#10-32 x 3/8" PHMS) - (4, packaged separately, taped to DSP
bracket on Cart Column)
•
Post cap plate – (1, in Cart Column packaging)
•
Button head socket cap screws (#1/4-20 x 3/8" BHSCS) – (4, packaged with post cap
plate)
ALGO® 5 Newborn Hearing Screener Service Manual
P/N 000995 Rev.A
1
Advertisement
Related Manuals for natus ALGO 5
Summary of Contents for natus ALGO 5
- Page 1 Examine the shipping containers carefully upon receipt. If any of the boxex are damaged or the packing materials show signs of stress, notify the carrier and keep the shipping materials for the carrier’s inspection. The ALGO 5 includes these items packaged and shipped separately in 4 boxes:: • Cart base with Isolation Transformer •...
- Page 2 Below is a view of the assembled ALGO 5: Panel PC DSP Box Keyboard Drawer for Disposables Cart Column with Integrated Label Printer Cable Management Shelf Space Page Printer (optional) Isolation Transformer FIGURE 1: ALGO 5— front view ALGO® 5 Newborn Hearing Screener Service Manual...
- Page 3 & PCA 5 Cables column Power Supply for Label Printer mounted in the column Optional Power Supply for Inkjet Page Printer Main Switch FIGURE 2: ALGO 5 — rear view ALGO® 5 Newborn Hearing Screener Service Manual P/N 000995 Rev.A...
- Page 4 ATA 5 PCA 5 Preamp 5 Figure 3: ALGO 5 Accessories 2. Mount the ALGO 5 Cart Column onto the Base • Open shipping carton. • Lift the cart base from its packaging. Set the cart base on the floor. Note the opening in the cart base that allows the column to be mounted to the base (FIGURE 4).
- Page 5 FIGURE 4: Mount Column onto the Base FIGURE 5: Hardware used to secure the Column to the base • Place protective cardboard or plastic on the floor, and carefully lay the cart column on the floor next to the base, with the flat side of the column (shelf side) facing down and the main switch facing up (see FIGURE 6 for orientation): ALGO®...
- Page 6 FIGURE 6: Cart from the back • With the shelves facing down, align the base opening with the column. Carefully route the six cables hanging from the bottom of the cart column one at a time through the opening in the cart base. The opening allows the column to be fitted in only one way (see FIGURE 4).
- Page 7 • Hand-tighten the plastic nut at the base of the main switch if it is loose (FIGURE 7). Insert nuts with integrated lock washers onto each of the two threaded studs with the lock washer towards the column, and then tighten the nuts using the 7/16” wrench. Tighten until snug, and then tighten at least an additional half turn so that lock washer bites into base metal.
- Page 8 • Route the Cables o Install the inlet power cord from the Power Inlet to the Isolation Transformer (FIGURE 9 and FIGURE 10). Inlet Power Cord FIGURE 9: Inlet Power Cord Location Inlet Power Cord FIGURE 10: Route the cables o Insert remaining five cables in such a way that (1) the thinnest cable is inserted in the uppermost outlet and (2) for the remaining four cables, the shortest cable lengths are inserted into the nearest plugs (FIGURE 10).
- Page 9 3. Install the Panel PC power supply Note: The Cart Column has two pre-installed power supplies, one for the DSP Box and one for the label printer. • Unpack the power supply for the Panel PC (included in the Panel PC box). •...
- Page 10 Stand the assembled cart column upright on the cart base. Unpack the Panel PC and lay it face down on a flat surface. CAUTION: To avoid scratching the screen surface, DO NOT remove the protective film until the ALGO 5 is completely assembled.
- Page 11 • Be certain that the tilt tension screws that hold the PC mount to the cart column (the top two – FIGURE 16) are tightened securely to hold the pivot in place. Hang the Panel PC on the PC mount by sliding the two screws inserted in the previous step onto the slotted screw holes (FIGURE 15).
- Page 12 5. Install the Keyboard • Unpack the keyboard and set aside. Pull the top drawer all the way out from beneath the writing surface to reveal the front of the cart column. • The DSP mounting bracket must be temporarily moved to provide access for routing the printer cable to the Panel PC (see FIGURE 17).
- Page 13 NOTE: To facilitate routing the keyboard USB cable, the sliding keyboard tray may optionally be removed. To remove the tray, pull it out fully. Press the tabs on both sides simultaneously while pulling on the tray (FIGURE 19). The rails that hold the tray are greased, so clean-up may be required.
- Page 14 Power Connection DSP Box – COM Port 1 Scanner Keyboard Full Size Printer Label Printer FIGURE 20: Panel PC Interface • Return the keyboard tray and the top drawer to their original positions. Loosen the screws that secure the DSP mounting bracket, slide the bracket back down to its original position, and tighten BOTH screws to ensure ground contact (FIGURE 17).
- Page 15 FIGURE 21: DSP Box to the mounting bracket • After the DSP Box is installed, tighten the grounding screw (10x32) as shown in FIGURE 22 until the screw breaks the outer coating of the DSP box to come into contact with the aluminum. This will provide an electrical connection between the DSP mounting bracket and the DSP Box.
- Page 16 FIGURE 23: Back with open Column • The communications cable that is attached to the DSP Box must be plugged into COM Port 1 of the Panel PC (FIGURE 20). 7. Connect the Preamp 5 to the DSP Box • Unpack the Preamp 5 (see FIGURE 3).
- Page 17 9. Install the Label Printer • Unpack the Label Printer. Unpack the USB cable for the printer from the accessories box. Attach the USB cable into the Panel PC (FIGURE 20). Route the cable down to the middle cart shelf, using the front or back U-channel of the cart column. •...
- Page 18 10. Add Optional Equipment if Provided (If no optional equipment was ordered, skip to Section 11, “Closing the Cart Column”) Barcode Scanner 10.1. • Unpack the scanner. Insert the USB cord from the scanner into the Panel PC (see FIGURE 20). Place the scanner onto the scanner holder (see FIGURE Barcodes for the LS2208 Barcode Scanner The following barcodes need to be scanned into the scanner to produce the appropriate line feed, remove sound after good decode, and reduce its volume...
- Page 19 • This barcode disables the scanner of any sound after a successful decode. • This barcode reduces the volume of the barcode scanner upon start-up. Full Size Printer – Inkjet (external Power Supply required) 10.2. • Unpack the Inkjet Printer. Unpack the external power supply. Set the printer on the bottom shelf of the cart.
- Page 20 After the cover is in place, install the Column Cap with the four button head cap screws ((#1/4-20 x 3/8” BHSCS) using the 5/32” allen wrench. FIGURE 27 shows the fully assembled ALGO 5 with protective covers in place. FIGURE 27: ALGO 5 —rear view with column cover snapped in ALGO®...