en Safety Safety Observe the following safety instructions. General information ¡ Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe for future reference or for the next owner. ¡ Do not connect the appliance if it has been damaged in transit. Intended use Only use this appliance: ¡...
Page 5
Safety en WARNING ‒ Risk of electric shock! ¡ Incorrect installation is dangerous. ▶ Connect and operate the appliance only in accordance with the specifications on the rating plate. ▶ Always use the supplied power cable for the new appliance. ▶ Connect the appliance to a power supply with alternating current only via a properly installed socket with earthing.
en Safety WARNING ‒ Risk of injury! Hinges move when opening and closing the appliance door and can cause injury. ▶ If built-under or integrable appliances are not in a cavity so that one side is accessible, the hinge area must be covered at the side.
Page 7
Safety en WARNING ‒ Risk of injury! ¡ Leaving the appliance door open may result in injury. ▶ Only open the appliance door to load or unload tableware in order to prevent accidents, e.g. through tripping. ▶ Do not sit or stand on the appliance door when open. ¡...
en Safety Damaged appliance WARNING ‒ Risk of electric shock! ¡ If the appliance or the power cord is damaged, this is danger- ous. ▶ Never operate a damaged appliance. ▶ Never operate an appliance with a cracked or fractured sur- face. ▶ Never pull on the power cord to unplug the appliance. Al- ways unplug the appliance at the mains.
Safety en WARNING ‒ Risk of harm to health! Children can lock themselves in the appliance, thereby putting their lives at risk. ▶ With redundant appliances, unplug the power cord. Then cut through the cord and damage the lock on the appliance door beyond repair so that the appliance door will no longer close.
en Preventing material damage Only use the water hoses sup- ▶ Preventing material damage Preventing material dam- plied with the appliance or genu- ine spare hoses. Never re-use water hoses that ▶ have been used before. Preventing material damage Safe installation ¡...
Childproof lock en To prevent corrosion, do not use ▶ Environmental protection and saving energy Environmental protection sponge cloths on dishwashers with a stainless steel front or and saving energy rinse such cloths thoroughly several times before using them Environmental protection and saving energy for the first time.
en Environmental protection and saving energy During the drying phase moisture Sensor setting Description from the interior of the dishwasher is Standard Optimum setting for a stored in the mineral and heat energy mixed load and heavily is released. The heat energy is blown soiled tableware.
Installation and connection en installing it under a continuous work- Installation and connection Installation and connec- top that is securely connected to ad- jacent cabinets. tion "Follow the safety instructions." To ensure proper operation, connect Installation and connection → Page 4 the appliance to the power and water "Follow the instructions for elec- supply correctly.
en Installation and connection Drinking water connection Connect your appliance to a drinking water connection. Installing the drinking water connection Note ¡ If you are replacing the appliance, you must use a new water supply hose. Consult the installation instructions supplied for the steps required here.
Familiarising yourself with your appliance en Familiarising yourself with your appliance Familiarising yourself with your appliance Familiarising yourself with your appliance Appliance You can find an overview of the parts of your appliance here. Rating plate Rating plate with "E number and FD number" → Page 63.
en Familiarising yourself with your appliance "Detergent" → Page 30 is added to the detergent Detergent dispenser dispenser. "Bottom basket" → Page 23 Bottom basket Dispenser for special salt Add special salt to the dispenser for special salt. → "Water softening system", Page 27 Lower spray arm The lower spray arm washes the tableware in the bot- tom basket.
Page 17
Familiarising yourself with your appliance en "Switching on the appliance" → Page 35 ON/OFF button and reset button "Switching off the appliance" → Page 36 "Terminating the programme" → Page 36 "Programmes" → Page 19 Programme buttons Info button If you press , the display shows information about selected programmes, basic settings and additional functions.
Page 18
en Familiarising yourself with your appliance buttons You can use these buttons to scroll between the basic settings. → "Changing basic settings", Page 39 Display The display shows information about pro- grammes, basic settings or additional functions. You can change the basic settings via the display and the setting buttons.
Programmes en Programmes Programmes You can find an overview of the pro- runtime will change if the rinse aid Programmes grammes that can be selected here. system is switched off or rinse aid Different programmes, which can be needs to be added. found on the control panel of your The consumption values can be appliance, are available depending...
Page 20
en Programmes Programme: Programme sequence Additional func- tions Tableware: Particularly gentle: SpeedPerfect+ ¡ Cleaning delicate table- ¡ Pre-Rinse Settings in the Intelligent ware, cutlery, temperat- Home Connect ¡ Cleaning 40 °C ure-sensitive plastics, app are adjustable ¡ Intermediate rinse → "Intelligent glasses and stemware. ", ¡...
Additional functions en flashes. Information for test institutes a The programme and the additional Test institutes are provided with in- function are saved. formation for comparability tests, e.g. Tip: To reset the programme, either according to EN60436. use the Home Connect app or reset These are the conditions for conduct- your appliance back to the factory ing the tests, however they are not...
en Features Additional func- Additional func- tion tion gramme and at any ¡ For a better drying res- time when the pro- ult the final rinse tem- ExtraDry gramme is running. perature is increased ¡ Energy and water con- and the drying phase sumption are increased.
Features en Adjusting top basket with side Bottom basket levers Arrange pans and plates in the bot- To wash large items of tableware in tom basket. the baskets, adjust the shelf position of the top basket. Pull out the top basket. To prevent the basket from sud- denly dropping down, hold the side of the basket by the top edge.
en Features Arrange cutlery with the points and sharp edges downwards. You can reorganise the cutlery drawer to make more space for longer/wider items of cutlery. Reorganising cutlery drawer You can fold down the side shelves and front prongs to make more space for longer/wider items of cut- lery.
Features en Folding prongs Extra Clean Zone Use the folding prongs to position Use the Extra Clean Zone in the top tableware securely, e.g. plates. basket to clean soiled tableware thor- oughly, e.g. muesli bowls. You can fold the prongs down to po- sition pans, bowls and glasses Selecting Extra Clean Zone better.
en Before using for the first time Pull the tab on the Extra Clean Place the Extra Clean Zone in the Zone up and forwards . top basket and lock in place . Check that the mounts are in the Set the slider to ON.
Water softening system en Note: If you select Initial start-up To remove any marks from water Home Connect here, make further or other residues, we recommend settings using the Home Connect you operate the appliance without app on your mobile device. tableware before using it for the You can change the settings for first time.
en Water softening system to the dispenser for special salt Setting the water softening immediately before the pro- system gramme starts. Set the water hardness on your appli- Unscrew the lid of the dispenser ance. for special salt and remove. Determine the water hardness and On initial start-up: Fill the dispenser the appropriate setting value.
Rinse aid system en stances. According to manufactur- Additional run time in minutes ers, combined detergents with salt Additional water consumption in replacement substances can gen- litres erally only be used up to a water Additional power consumption in 0.05 hardness of 26 °E without adding special salt.
en Detergent Add rinse aid up to the max mark. Switching the rinse aid sys- tem off If you find the rinse aid refill indicator irritating, e.g. when using combined detergents with a rinse aid compon- ent, you can switch the rinse aid sys- tem off.
Detergent en With powder and liquid detergent the Detergent Description dosage can be individually adjusted Tabs Tabs are suitable for all to the level of soiling of the table- cleaning functions and do ware. not need to be measured For better washing and drying results out.
en Detergent Add the detergent to the dry deter- Detergent Description gent dispenser. Detergent con- Chlorine residue on table- taining chlorine ware may present a risk to 50 ml health. 25 ml 15 ml Information on detergents Follow the instructions on detergents in everyday use.
Tableware en Close the lid of the detergent dis- Damage to glass and table- penser. ware Only put glasses and china in the dishwasher if it is marked as dish- washer-safe by the manufacturer. Avoid damage to glass and table- ware. Cause Recommendation The following table-...
en Tableware To save resources, do not pre- Cause Recommendation rinse tableware under running wa- The water temperat- Select a programme ter. ure of the programme with lower temperat- Observe the following when arran- is too high. ures. ging tableware: After the programme –...
Basic operation en for the combination of energy/wa- Removing tableware ter consumption for this type of tableware and evidences conform- WARNING ity with the EU Ecodesign Direct- Risk of injury! ive. Hot tableware can cause burns to the If you do not perform any actions skin.
en Basic operation "Finish at" (e.g. 15:20 hours). You Press to resume the pro- can change this setting in the "Ba- gramme. sic settings" → Page 37. Close the appliance door. To activate timer programming, press . Terminate programme Note: To deactivate timer program- To end a programme early or to ming, press for approx.
Basic settings en Basic settings Basic settings You can configure the basic settings for your appliance to meet your needs. Basic settings Overview of basic settings The basic settings depend on the features of your appliance. Basic setting Selection Description Time setting 00:00 - 24:00 Set the current time.
Page 38
en Basic settings Basic setting Selection Description Eco forecast Switch EcoCheck on or off. When selecting the programme, the average wa- ter consumption and energy consumption is briefly shown on the display. Emotion Light Switch the interior lighting of the appliance on or On via main switch off.
Home Connect en Basic setting Selection Description Efficient Dry Activate or deactivate automatic opening of the On in all programmes appliance door during the drying phase. On with Eco 50° If the function has been activated, the running time may increase. → "Efficient Dry", Page 12 Wi-Fi Switch the wireless network connection on or off.
en Home Connect Home Connect services in your coun- Connecting the appliance to WLAN try. You can find information about home network (Wi-Fi) this at: www.home-connect.com. Requirements To be able to use Home Connect, ¡ Home Connect app is installed on you must first set up the connection your mobile device.
Home Connect en Activating Remote Start Data protection When you have selected "Manual" in Please see the information on data the basic settings of this function, ac- protection. tivate the function on your appliance. The first time your appliance is Requirements registered on a home network ¡...
en Cleaning and servicing Cleaning products Cleaning and servicing Cleaning and servicing Only use suitable cleaning products To keep your appliance working effi- Cleaning and servicing to clean your appliance. ciently for a long time, it is important → "Safe use", Page 10 to clean and maintain it carefully.
Cleaning and servicing en To ensure optimum cleaning perform- Only use machine care products ance, the programme doses the de- specially designed for dishwash- tergents independently of each an- ers. other during the relevant cleaning Pour the machine cleaner into the phase.
en Cleaning and servicing Turn the coarse filter anticlockwise Carefully clean the rim of dirt and remove the filter system . between the coarse and the fine fil- ter. Check that no foreign objects ‒ Re-assemble the filter system. fall into the sump. Make sure that the locking catches on the coarse filter click into posi- tion.
Page 45
Cleaning and servicing en Pull up the lower spray arm to re- move. Check the outlet nozzles on the spray arms for blockages under running water and remove any for- eign bodies. Insert the lower spray arm. a The spray arm clicks into position. Insert the upper spray arm and screw it firmly in place.
en Troubleshooting Troubleshooting Troubleshooting You can rectify minor faults on your appliance yourself. Read the troubleshoot- Troubleshooting ing information before contacting after-sales service. This will avoid unneces- sary costs. WARNING Risk of electric shock! Incorrect repairs are dangerous. Repairs to the appliance should only be carried out by trained specialist ▶...
Page 47
Troubleshooting en Fault Cause Troubleshooting Appliance door does not Appliance door brushes Install the appliance correctly as de- ▶ open at the end of the pro- against the appliance or kit- scribed in the installation instruc- gramme. chen cabinets tions and align. Appliance door opens too Door is not correctly adjus- Adjust the appliance door as de-...
en Troubleshooting Fault Cause Troubleshooting Appliance door opens too Door is not correctly adjus- Adjust the appliance door as de- ▶ wide when activated. ted. scribed in the installation instruc- tions. Error code / Fault display / Signal Fault Cause Troubleshooting E:2060 lights up.
Page 49
Troubleshooting en Fault Cause Troubleshooting E:3200 or indicator for wa- Remove the filter from the supply ter supply lights up. hose Clean the filter. Re-insert the filter in the supply hose. Screw the water connection back Check the water connection for leaks.
en Troubleshooting Fault Cause Troubleshooting E:9001 lights up. Mains voltage is too low. This is not a fault on the appliance. Contact an electrician. Have the mains voltage and elec- trical installation checked by an electrician. E:9240 lights up. Filters are soiled or blocked. Clean the filters.
Page 51
Troubleshooting en Fault Cause Troubleshooting Tableware is not dry. Water collects in recesses of Position tableware at an angle ▶ the tableware or cutlery. where possible. The combined detergent Use rinse aid to improve drying per- used has a poor drying per- formance.
Page 52
en Troubleshooting Fault Cause Troubleshooting Appliance interior still wet Not a fault. The condensa- No action required. after wash cycle. tion drying principle causes water droplets in the tub – they are indeed desirable here. The moisture in the air condenses on the inside walls, runs off and is pumped out.
Page 53
Troubleshooting en Fault Cause Troubleshooting Detergent residue in the ap- Lid of the detergent dis- Arrange tableware in the top basket pliance penser is blocked by items tableware so the tab collecting tray of tableware parts and will is not obstructed by tableware. → "Arrange tableware", Page 34 not open.
Page 54
en Troubleshooting Fault Cause Troubleshooting Stubborn white coatings are Detergent substances are Change your "detergent" ▶ → Page 30. present on tableware, inside deposited there. These coat- the appliance or the door. ings cannot generally be re- Clean the appliance mechanically. ▶ moved with chemicals. The hardness range is set in- Set the Water softening system to ▶...
Page 55
Troubleshooting en Fault Cause Troubleshooting Coloured coatings (blue, yel- You can remove deposits with "Mechanical cleaning" → Page 42 low, brown) that are difficult or impossible to remove are or a machine cleaning product. It present inside the appliance may not always be possible to com- or on stainless steel table- pletely remove deposits but they ware.
Page 56
en Troubleshooting Fault Cause Troubleshooting Removable streaks are Tableware has been pre- Only remove large remnants of food ▶ present on glasses, glass- cleaned too intensely. The and do not prerinse tableware. ware with a metallic appear- sensors chose a weaker pro- Adjust the sensitivity of the sensors.
Troubleshooting en Fault Cause Troubleshooting Excessive formation of foam Detergent or appliance care Change the brand of detergent. ▶ occurs. product used causes excess- ive foaming. Home Connect problem Fault Cause Troubleshooting Connection to home net- WLAN on router is not act- Check the wireless network con- ▶...
Page 58
en Troubleshooting Fault Cause Troubleshooting → "Terminate programme", Water is left in the appliance ▶ at the end of the pro- Page 36 gramme. Appliance cannot be Software update is taking Wait until the software update has ▶ switched on or operated. place. finished.
Troubleshooting en Fault Cause Troubleshooting All LEDs lit up or flashing. Electronics have detected a Press the main switch button for ap- fault. prox. 4 seconds. → "Controls", Page 16 The appliance is reset and restar- ted. If the problem occurs again: Switch off the appliance. ‒...
Page 60
en Troubleshooting Fault Cause Troubleshooting Knocking or rattling noise. Spray arm is striking table- Arrange tableware so that the spray ▶ ware. arms do not strike tableware. With a small load the water Distribute the tableware evenly. ▶ jets directly strike against Load the appliance with more table- ▶...
Transportation, storage and disposal en Insert the pump cover and press Clean wastewater pump down . Large remnants of food or foreign bodies can block the waste water pump. As soon as the rinsing water no longer drains properly, the waste water pump must be cleaned.
en Customer Service Protect appliance from frost Disposing of old appliance If there is a risk of frost where the ap- Valuable raw materials can be re- pliance will be standing, e.g. in a holi- used by recycling. day home, empty the appliance com- pletely.
Technical specifications en least 10 years from the date on from water damage, the appliance which your appliance was placed on must be connected to the power the market within the European Eco- supply. nomic Area. ¡ The liability guarantee is valid for the service life of the appliance.
en Declaration of Conformity This product contains light sources The source code will be made avail- from energy efficiency class G. These able to you on request. light sources are available as a spare Please send your request to oss- part and should only be replaced by request@bshg.com or BSH Hausger- trained specialist staff.
Page 65
Declaration of Conformity en 2.4 GHz band (2400–2483.5 MHz): Max. 100 mW 5 GHz band (5150–5350 MHz + Only applies to Great Britain 5470–5725 MHz): Max. 100 mW UK (NI) 5 GHz WLAN (Wi-Fi): For indoor use only. 5 GHz WLAN (Wi-Fi): For indoor use only.
Page 68
Thank you for buying a Bosch Home Appliance! Register your new device on MyBosch now and profit directly from: • Expert tips & tricks for your appliance • Warranty extension options • Discounts for accessories & spare-parts • Digital manual and all appliance data at hand •...