Subscribe to Our Youtube Channel
Related Manuals for ITW SIMCO ION SS-50
Summary of Contents for ITW SIMCO ION SS-50
- Page 1 SS-50 Super Service Static Neutralizing Bars & Power Supplies INSTALLATION AND OPERATING INSTRUCTIONS SS-50 Bars 5200210 Rev. A...
- Page 2 (This page intentionally left blank) SS-50 Bars 5200210 Rev. A...
-
Page 3: Table Of Contents
TABLE OF CONTENTS 1. SAFETY WARNINGS ....................1 2. INTRODUCTION ......................2 Receipt of Equipment ......................2 Return Shipments ........................2 3. SPECIFICATIONS .....................3 4. INSTALLATION ......................4 Grounding ..........................4 Mounting Static Neutralizing Bars ..................4 Mounting Power Supplies .....................4 Installing High Voltage Cables .....................4 5. OPERATION ......................5 6. -
Page 4: Safety Warnings
1. SAFETY WARNINGS NOTE! – Statements identified with a NOTE indicate precautions necessary to avoid potential equipment failure. CAUTION! – Statements identified with a CAUTION indicate potential safety hazards. NOTE! – This equipment must be correctly installed and maintained. Adhere to the following notes for safe installation and operation. 1. -
Page 5: Introduction
2. INTRODUCTION The SS-50 Super Service static neutralizing bar features high pin density and Teflon insulation. The high pin density, along with emitter pins being direct coupled to the power supply output provides effective static elimination even at high web speeds. The Teflon insulation allows for easy cleaning of aggressively sticky contaminants. -
Page 6: Specifications
3. SPECIFICATIONS SS-50 Operating Voltage 5 kV AC Humidity 70% RH max, no dewing permissible Dimensions 1/2”W x 19/32”H Mounting Studs 6-32 Enclosure Anodized Aluminum Inner Bar Material Teflon Emitter Point Stainless Steel (Type 303) H164 H264 H254 N164S N264S Input Voltage 120V 230V... -
Page 7: Installation
4. INSTALLATION Grounding 1. It is essential that the machine frame be grounded either through well-grounded electrical conduit or by heavy copper wire connecting the frame to a water pipe. 2. The static neutralizing bar’s metal casing must be grounded to avoid operator shock and to ensure proper operation. -
Page 8: Installing High Voltage Cables
Installing High Voltage Cables 1. Route the high voltage cables attached to each static bar along the machine frame or wall to the power supply. 2. Cable supports are used to guide the cables back to the power supply. All cables must be kept a minimum of 1/4”... -
Page 9: Troubleshooting
6. TROUBLESHOOTING NOTE! – Only qualified service personnel are to perform trouble-shooting tasks. If equipment fails to function properly: 1. De-energize the power supply. 2. Ensure all ground connections are intact. 3. Check that all cable connections are tight. NOTE! – FINGER TIGHTEN ONLY. 4. -
Page 10: Maintenance
7. MAINTENANCE NOTE! – Only qualified service personnel are to perform maintenance tasks. NOTE! – Never use hard or sharp objects to scrape ionization points. CAUTION! – ELECTRICAL SHOCK HAZARD De-energize all power supplies before performing any maintenance tasks. CAUTION! – FIRE HAZARD Never energize a power supply with any trace of alcohol remaining on the equipment. -
Page 11: Replacement Parts
8. REPLACEMENT PARTS 5050252 SS-50 Bar mounting kits (contains 2 brackets and hardware) 5050002 SLCC HV Connector Kit 4800061 Plastic Insulating Tubing 4670204 Cleaning Brush 4050556 Tension Voltage Detector 9. WARRANTY This product has been carefully tested at the factory and is warranted to be free from any defects in materials or workmanship. - Page 12 Simco-Ion 2257 North Penn Road Hatfield, PA 19440 (215) 822-6401 (800) 203-3419 www.simco-ion.com customerservice@simco-ion.com © 2021 Simco-Ion Printed in the U.S.A. SS-50 Bars 5200210 Rev. A...
Need help?
Do you have a question about the SIMCO ION SS-50 and is the answer not in the manual?
Questions and answers